Pandora Pandect X1100 User manual
1User manual
2Motorcycle service and security system Pandect X-1100
Pandora thanks you for choosing Pandect X1100 security system
Pandect X-1100 is a premium-class service and security system, designed for motorcycles. It
was developed and produced in Russia, in a cozy industrial city of Kaluga in the west of Russia, on
a privately owned “Experimental Engineering Factory” (“Pandect” is a registered trade mark, reg no.
311323).
This device was developed by a group of Russian engineers with the highest qualification. It in-
cludes a number of highly advanced and unique technological, software and design solutions.
When building Pandect X-1100 we were using the most up-to-date electronics from world’s best
manufacturers. The device is built using high-precision mounting and control machinery, thus we
guarantee highest possible quality, reliability and stable technical characteristics for the whole opera-
tion period.
Pandect X-1100 has a cryptographically strong authorization code with unique dialog algorithm
and individual 128 bit encryption key on every device. Experimental Engineering Factory guarantees
100% protection form electronic hacking for the whole operation period.
The system is built for your convenience: it’s ergonomic, reliable, has the highest security and
service characteristics, 3 years unconditional warranty and free service and support on the territory of
European Union. We are happy to provide any support we can – feel free to use our online or phone
support.
Our website: www.pandora-moto.gr
Support hotline: +302105814441
3User manual
Table of contents
General information 5
System features 6
Security zones 7
System set 7
Controlling security using radio tag button (arming/disarming) 8
Hands free mode 8
Slave mode 8
Disabling Immobilizer and AntiHiJack in case of emergency 9
Owner’s personal safety – immobilizer 10
Immobilizer mode 11
AntiHiJack mode 11
Replacing immobilizer tag battery 12
Control over system in case of emergency, entering individual PIN code 13
Pandora and a cell phone 14
Control over system via phone 15
Voice information 15
Repeating last message 15
Arming/disarming 16
Event history 16
Enabling microphone 16
Requesting system’s account balance 16
Requesting system’s coordinates 16
Enabling/disabling additional channel 17
Enabling/disabling automatic engine starts 17
Blocking/unlocking the engine 17
Changing settings via phone 18
4Motorcycle service and security system Pandect X-1100
System installation and set up 19
Installation requirements 20
Connection of the base unit 21
Wiring diagram 22
Programming the systems, entering PIN code 25
Changing setting via 2,4GHz wireless interface 26
Programming menu using VALET button 26
Changing settings using VALET button 27
Additional devices 31
Blockage Radio Relay 31
Connecting RR 100 radio relay 32
Programming the radio relay 32
Supplementary module RHM-02 32
Programming supplementary module RHM-02 34
GSM/GLONASS - receiver NAV-03 34
Programming GSM/GLONASS - receiver NAV-03 34
Important information 35
Any problem can be solved 36
Buzzer sounds and winkers light signals 37
Meaning of the status indicator lights 37
Useful websites 39
Warranty obligations 40
Installation certificate 41
Acceptance certificate 42
Warranty card 42
5User manual
General information
1
6Motorcycle service and security system Pandect X-1100
System features
Base unit
•Dialogencryptionofcommands.•Individual128-bitencryptionkeythatcanbechangedbytheuser.•IndividualdisarmingPINcode.•RCblockagerelay(2,4GHz,frequency,upto3unitscanbeconnected).•Built-inintegralaccelerometerfordeterminingmotionandshockswithadaptiveprocessingalgorithm.
•Built-in2.4GHzaerial.•Advancedprocessofsensordatareading,eliminatingfalsealarmpossibilities.•Automaticarming.•Registersdelayforinteriorlightingwhenarming.•Hands-freemodeforarming/disarmingwithoutusingaremote.•Softwareupdatesviabuilt-inmini-USBsocket.Immobilizer tag
•Dialogencryptionofcommands.•Arm/disarmbutton•Individual128-bitencryptionkeythatcanbechangedbytheuser.•Built-inLEDindicator•CR2032battery.
7User manual
* - Availability of this function depends on car model
Security zones
•Triggeringoftheshocksensor(warninglevel•Triggeringoftheshocksensor(alarmlevel)•Triggeringofthemotionsensor•Triggeringofthetilitsensor•Ignitiontrigger•Brakepedalpressing•TopCase•SideCases•Seat•Criticallylowon-boardvoltage.System set
1. Base unit 1
2. Immobilizer tags 2
3. Leather case for immobilizer tags 1
4. Main cable 1
5. Cable with VALET button and three-colored light indicator 1
6. Fastening set 1
7. User manual 1
8. Plastic card with individual secret code 1
9. Packaging 1
10. Beeper (compact sound emitter) 1
11. Microphone 1
12. Turn signals relay 1
13. Blocking relay 1
Manufacturer reserves the right to change configuration and construction of the product to improve its technological and
operational parameters without notification.
8Motorcycle service and security system Pandect X-1100
Controlling security mode
To arm or disarm a security system while in the range of radio
channel (about 5 meters from the motorcycle) push a button on the
immobilizer tag. The system will communicate dialog security codes
(AES-128 encryption) in 2.4 GHz range on one of 125 channels and
your security system will be armed or disarmed. Special arming/
disarming algorithm is available for motorcycles. Arming is performed
by pressing the clutch lever when ignition is switched off; disarming
is performed by pressing the clutch lever when the system is armed.
The presence of the tag in radio the zone is controlled when arming/
disarming is performed. Arming/disarming using the clutch lever is
not allowed when the tag is not in the radio zone.
Hands free mode
System allows for programmable HANDS FREE arming/disarming. To arm the system when the
engine is running, simply move immobilizer tag away from the motorcycle outside of the 2.4 GHz
radio channel radius (more than 10 meters). To disarm the system move the tag back into the radius.
Slave mode
In this mode original motorcycle security system can be controlled via CAN or analog inputs. When
arming and disarming motorcycle’s original security system, Pandect X-1100 will arm and disarm too.
This does not require an immobilizer tag to be present in range, however, the engine will be blocked if
there will be an attempt to drive away without a tag present.
LED indicator
Control button
9User manual
Disabling Immobilizer and AntiHiJack in case of emergency
In case immobilizer tag is lost or broken, the system allows for emergency disabling of immobilizer
functions and ANTIHIJACK mode. To disable those call system’s phone number, wait for answer and
dial a DTMF command 998*.
To re-enable Immobilizer functions and AntiHiJack mode call the system’s phone number, wait
for answer and dial 888*.
VALET button can also be used to enter service PIN code and enter 15th programming level
(instructions at page 20).
Enter the first digit of the service code by Valet button (press the button a number of times equal
to the initial number, pauses between presses of the button should not exceed 1 second). The system
will confirm entry with red flash of the indicator. Enter the second, the third and the fourth digits the
same way. The system will confirm the correct code with red and green .ashes of the indicator. If the
code is entered incorrectly, a long red indicator’s flash will indicate it.
To switch on the immobilizer and AntiHiJack, enter the 15th programming level, LED will flash red
color. Press Valet button one time, LED will light with green color, the siren will sound one short beep.
Arming/disarming via a phone
To control the security system via a phone, call the system’s phone number, wait for response and
dial 1* to arm the system or 0* to disarm it.
ATTENTION! AFTER DIALING THIS COMMAND YOU WILL NEED TO ENTER A SECRET
PIN CODE FROM THE INDIVIDUAL OWNER’S PLASTIC CARD.
10 Motorcycle service and security system Pandect X-1100
Owner’s personal safety –
immbilizer
2
11User manual
Service-security system Pandect X-1100 is a highly effective antitheft and anti-hi-jack
security mean. System set has 2 immobilizer tags. For additional security 1 to 3 radio relays can
be installed on a motorcycle.
Immobilizer mode
When ignition is being switched on, Pandect X-1100 moto base unit performs a search for
immobilizer tags in radio range. If when the ignition is switched on no radio tags were detected, the
system will lock the engine with all radio relays that were programmed into the system. If analog relay
blockage is installed, it will lock immediately, before the motorcycle starts moving. If additional radio
relays blockages were installed, engine lock will only occur when radio relay motion sensor detects
movement of the motorcycle.
AntiHiJack mode
ANTIHIJACK mode helps to prevent aggressive stealing of the motorcycle when engine is running
and to protect the driver by using delayed engine blockage.
Every time when the engine is running and the brake pedal is pressed, immobilizer requests
response from the RF tag, using unique algorithm. After brake pedal was pressed while the engine
is running and the system cannot detect a radio tag, the engine will be stopped after 60 seconds
(Requirement to ensure driver safety). From the 30th second,“engine blockage warning“ ringtone will
play for the remaining 30 seconds.
If engine blockage is done via radio relay, when warning signals will end, or new attempts to start
the engine will commence, immobilizer will only allow it to start when the motorcycle is not moving,
and will block it again if will start movement. Immobilizer will be activated in 2 seconds after the
ignition is switched on. If the motorcycle starts moving, the immobilizer will block the engine for 15
seconds.
When the tag is returned into radio range the blockage will be canceled.
If engine blockage is done using analog relays, then when the sound signals end the engine will
be forced to stop until a tag will be detected again.
12 Motorcycle service and security system Pandect X-1100
Replacing immobilizer tag battery
Carefully open the cover of the tag’s battery compartment. Extract discharged battery and insert
a new one keeping in mind the correct polarity. Replacing a battery will not cause a loss of tag code
information, as authorization data is stored in the nonvolatile memory of the MCU.
Carefully close the cover of the tag’s battery compartment. All elements of construction should be
rigidly locked in places. If it is so, the tag can be operated as usually.
13User manual
Control over system in case of emergency, entering individual PIN code
In case you cannot disarm the system using a tag, owner’s individual PIN code can be used.
Individual PIN code is written on the owner’s plastic card under protective layer. Erase the protective
layer and use VALET button to input the PIN code.
1. Using VALET button, input the first digit of the code (press the button a number of times,
equal to the first digit; pauses between presses should not exceed 1 seconds). The system will confirm
with red LED indicator flash.
2. Similarly input second, third and fourth digit. Every input will be confirmed with red LED flash.
3. The system will confirm correct PIN with red and green flashes of LED indicator.
If the input was incorrect, it will be indicated with long red flash. New input can be attempted after
5 seconds.
4. If the system was armed, after entering the correct PIN code it will be disarmed.
ATTENTION! MAKE SURE THAT PROTECTIVE LAYER ON THE OWNER’S PLASTIC
CARD IS INTACT AFTER THE INSTALLATION OF THE SYSTEM. PLASTIC CARD HOLDS
INDIVIDUAL PIN CODE AND ONLINE SERVICE ACCESS INFORMATION.
For emergency arming when the engine is stopped, press and hold VALET button for 3 seconds.
The system will confirm with buzzer signal and will be armed in 30 seconds.
While there is a countdown, the LED will be lit red.
14 Motorcycle service and security system Pandect X-1100
Pandora and a cell phone
3
15User manual
Control over system via phone
Call the system’s phone number. When it answers, enter command code.
#
#
1
1*
*
0
0
9
9*
*
*
*
9
9
0
0*
*
7
7
0
00
0*
*
1
10
00
0*
*
1
12
23
3*
*
0
0
0
0*
*
1
1*
*
0
0*
*
3
32
21
1*
*
5
50
00
0*
*
4
45
56
6*
*
6
65
54
4*
*
7
78
89
9*
*
9
98
87
7*
*
6
66
66
6*
*
9
99
99
9*
*
2
25
58
8*
*
1
1
5
5
6
6*
*
6
65
51
1*
*
9
99
98
8*
*Disable immobilizer and AntiHiJack
8
88
88
8*
*Enable immobilizer and AntiHiJack
2
22
22
2*
*Disable Hands Free mode
2
22
23
3*
*Enable HandsFree arming
2
22
24
4*
*Enable Hands Free disarming
2
22
25
5*
*Enable HF disarming only with automatic start
7
78
89
9*
*
9
98
87
7*
*
Return to previous menu/state
Repeat the last message
Silent arming
Help
Silent disarming
Arming
Disarming
Event history
Switch on interior microphone
Request GSM account balance
Start the engine/prolong heating
Request current coordinates
Stop the engine
Switch on additional channel
Switch off additional channel
Switch on engine preheater
Switch off engine preheater
Enable automatic engine start
Disable automatic engine start
Enable engine blockage
Disable engine blockage
System information
Enable automatic engine start
Disable automatic engine start
ATTENTION! IF THE CALL IS NOT MADE FROM THE OWNER’S NUMBER, GUEST PIN
CODE SHOULD BE ENTERED. FACTORY SET GUEST PIN CODE IS 1234.
AFTER THE SYSTEM IS INSTALLED, PLEASE CHANGE FACTORY SET PIN.
Voice help
The system has voice help menu. During voice call to the system, press 9*(“STAR“) and listen to
the information about system control commands.
To end session hang up the phone.
Repeating the last message
To repeat any message press “STAR“during a voice call to the system.
16 Motorcycle service and security system Pandect X-1100
Arming/disarming
1. Call the system’s number and wait for answer.
2. Dial 1* to arm the system or 0* to disarm it. For silent arming dial 10*, for silent disarming 00*.
3. The system will confirm:“Arming/disarming“.
To end session hang up the phone.
Event history
1. Call the system’s number and wait for answer.
2. Dial 09*
3. Listen to the information about the latest event registered by the system.
To navigate event history press 4(listen to the previous/earlier event), or 6(listen to the next/
later event).
To end session hang up the phone.
Switching on interior microphone
1. Call the system’s number and wait for answer.
2. Dial 007*
3. The system will confirm execution and will switch interior microphone on.
To increase volume press 2, to decrease volume press 8.
To end session hang up the phone.
Request GSM account balance
1. Call the system’s number and wait for answer.
2. Dial 100*
3. The system will confirm:“Balance information sent via text message“ and will send text message
with account balance information to your phone.
To end session hang up the phone.
Request current coordinates
1. Call the system’s number and wait for answer.
2. Dial 500*
17User manual
3. The system will confirm:“Current coordinate sent via text message“ and will send text message
with coordinates and a web link to a map to your phone.
To end session hang up the phone.
Switching on/o additional channel
Pandora system can control additional timer channel:
1. Call the system’s number and wait for answer.
2. Dial 456* to switch the channel on or 654* to switch it off.
3. The system will confirm execution.
To end session hang up the phone.
Switching on/o engine preheater
Pandora system has additional control channel for engine preheater control:
1. Call the system’s number and wait for answer.
2. Dial 156* to switch the channel on or 651* to switch it off.
3. The system will confirm execution.
To end session hang up the phone.
Enabling/disabling automatic engine start
Pandora system has function of promptly disabling automatic engine start:
1. Call the system’s number and wait for answer.
2. Dial 987* to disable all automatic engine starts or 789* to enable all automatic engine starts.
3. The system will confirm execution.
To end session hang up the phone.
Blocking/unlocking the engine
You can lock motorcycle’s engine using any phone. The engine will remain blocked until phone
command “unlock engine“ will be sent. This blockage cannot be disabled using a remote.
1. Call the system’s number and wait for answer.
2. Dial 666* to enable engine blockage or 999* to disable engine blockage (after dialing 999*
you will need to enter individual PIN-code that is located on the owner’s plastic card).
1
1
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
6
6
*
*
7
7
*
*
8
8
*
*
9
9
*
*
0
0
1
1
*
*
2
2
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
6
6
*
*
7
7
*
*
8
8
*
*
6
6
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
7
7
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
6
6
*
*
7
7
*
*
8
8
*
*
9
9
*
*
0
0
1
1
*
*
3
3
*
*
1
1
*
*
2
2
*
*
4
4
*
*
1
1
*
*
2
2
*
*
3
3
*
*
4
4
*
*
5
5
*
*
5
5
*
*
1
1
*
*
2
2
*
*
3
3
*
*
8
8
*
*
9
9
*
*
Phone number
settings
Settings of the
voice calls
Automatic
engine start
settings
Settings of the
text messages
Immobilizer
settings
Additional
settings
Sensor
sensitivity
settings
Settings
of saving mode
Current time and
date settings
Owner's number -> «#»
Additional owner's
number -> «#»
Second additional owner's
number -> «#»
Account balance inquiry
number -> «#»
Voice calls on alarm
Voice calls on triggering warning
level of the sensors
Voice calls on engine start
Voice calls on engine stop
Voice calls on restoring GSM
connection
Voice calls on disarming
Voice calls on entering programming
mode
Voice calls when radio relay
connection is lost
Voice calls when on-board voltage
is low
Voice calls on accident
Text messages on alarm
Text messages on triggering warning
level of the sensors
Text messages on engine start
Text messages on engine stop
Text messages on restoring GSM
connection
Text messages on disarming
Text messages on entering
programming mode
Text messages when radio relay
connection is lost
Text messages when on-board
voltage is low
Text messages on accident
Immobilizer (on/off)
Anti-Hi-Jack
Changing guest PIN code
Entering as guest
Remote blockage
Switch on interior microphone
Set threshold voltage for sending text
message
By time
Set up time for automatic launch
By voltage
Set up voltage for automatic launch
By temperature
Set up temperature for automatic
launch
By period
Set up period for automatic launch
Settings of the warning level of the
shock sensor sensitivity
Settings of the alarm level of the
shock sensor sensitivity
Settings of the motion sensor
sensitivity
Settings of the warning level of the
supplementary sensor sensitivity
Settings of the alarm level of the
supplementary sensor sensitivity
GSM connection
Money saving mode of the GSM
connection
Voice calls in roaming service
Changing settings via phone
To enter programming mode, call the system’s number, wait for answer, switch the ignition on,
and in no more than 5 seconds switch it off. The system will switch into settings programming mode.
Using voice help, program main settings.
19User manual
System installation
and set up
4
20 Motorcycle service and security system Pandect X-1100
General installation requirements
•Rigidlysecureeveryelementofthesystem, as regular usage of the motorcycle can
create conditions that may damage not only the
functionality of motorcycle alarm, but also the
standard systems of the motorcycle, including
the in-movement security elements.
•Thesysteminstallationisbettertobedonewith disabled connectors and disconnected
battery minus clamp.
•TheinstallationofCAN-buswiresshouldbeconducted only when the power of the base unit
is switched off.
•Theinstallationofthemotorcyclealarmcan be conducted by twisting the wires together
or soldering with lead-tin solder and subsequent
isolation of the attachment area.
•Whenconnectingthewirestogether,payattention to the diameter and the materials of
the wires. When they are different, bring the
electrochemical potentials to the minimum
difference. Thoroughly isolate such combination.
Moisture should not be entering the area of
contact, as it will increase the electrochemical
corrosion of the conductors (important for
circuits with heavy current flows).
•Itisrecommendedtoplacecommutableconnections as high as possible in chambers so
that the water condensate that forms on the wire
does not form water drops on the connection
area. •Whencommutatingthewires,leavealittle slack, allowing sufficient sag to prevent the
destruction of the compounds from vibration
when driving.
•Donotinstallthewiresinplaceswheretheir isolation can be damaged by attrition.
•Placetheelectroniccomponentsofthesystem higher and sockets down, to avoid the
condensate leaking in the PCB and electronic
components through the sockets gaps.
•Mountingthebaseunitofthealarm,ensureits rigid attachment to the motorcycle body for
the proper operation of the shock sensor.
•Itisrecommendedtoshortenallunusedoutputs of the system during the installation,
reliably insulate and fixate them in order to avoid
the occasional touch with the motorcycle body
or any the other conductors.
Table of contents
Other Pandora Security System manuals
Pandora
Pandora DXL-0070L User manual
Pandora
Pandora Smart Moto User manual
Pandora
Pandora dlx5000 User manual
Pandora
Pandora Camper User manual
Pandora
Pandora 397O User manual
Pandora
Pandora Mini v3 User manual
Pandora
Pandora SMART PRO V3 User manual
Pandora
Pandora Camper Mini User manual
Pandora
Pandora Camper Pro v2 User manual
Pandora
Pandora Camper Pro User manual
