Pandora DXL-0070L User manual

Pandora would like to thank you for choosing
our DXL-0070L service and security system
Pandora is a brand of Russian Experimental Engineering Factory, a full production cycle
electronics R&D facility. We design and produce car service-security systems for more than 10 years
and have reached a considerable success on Russian and post-communist markets – biggest security
system markets in the world. Our systems are made to withstand severe weather conditions and
criminal situation of northern Eurasia.
Pandora DXL-0070L is a premium car service-security system, built for cars with on-board
voltage of 12V. It is a complex engineering solution which includes car security system, telemetry,
remote and automatic engine start and various service options, all accessible via RF control remote
that can replace your factory remote. This system is designed to be all-in-one car service and security
solution and requires no additional modules: it includes algorithmic keyless bypass that works with
many popular car models. For even more convenience, it allows remote control over Webasto or
Eberspaecher preheaters – and even sequential use for automatic engine start.
WARNING!
IT IS STRONGLY ADVISED TO HAVE PROFESSIONAL CAR MECHANIC INSTALLING
THE SYSTEM. CERTIFIED INSTALLERS ARE RARE OUTSIDE RUSSIA, BUT ANY CAR
ELECTRONICS INSTALLER SHOULD BE ABLE TO INSTALL PANDORA DXL0070L
USING INSTALLATION SCHEME IN THIS MANUAL AND ALARMSTUDIO SOFTWARE.
MOST FEATURES ARE HIGHLY DEPENDENT ON COMPETENT INSTALLATION.
OUR SYSTEMS ARE THOROUGHLY TESTED FOR QUALITY, SO IF A FEATURE FAILS
TO PRODUCE EXPECTED RESULTS, MOST LIKELY THE PROBLEM IS IN IMPROPER
INSTALLATION.
It is essential for systems functioning that you read and understand instructions in this manual.
Note that all radio devices are subject to interference, which could affect proper performance.
This device has limited external factors resistance. It should not be subjected to water beyond occasional splatter, or operated in
temperatures outside -40 to +80 oC range.
IMPORTANT! Note that this manual describes remote and manual functions for the
most part. Functionality of the system is vast and would require a book-sized manual to
fully describe. Instead we use a handy software named AlarmStudio that functions as both
programming tool and an extended installation & functionality manual. It requires Windows
and can be downloaded at pandorainfo.com
Product is in conformity with Electromagnetic Compatibility
Directive EMC 2004/108/EC and R&TTE Directive 1999/5/EC

3
2User manualPandora DXL-0070L service-security system
System features
2-way LCD remote
• Arming and disarming security system using separate buttons.
• Controls status of 10 independent security zones.
• Vibrating alert.
• 16 notification ringtones.
• Automatic LED lighting of the LCD.
• Vibration confirmation of the button press.
• AAA battery (1,5V).
• Battery level indicator.
• Current time indication, alarm clock.
• Time synchronizes with the base unit for exact time stamp in the event history.
• Engine* and interior temperature, voltage indication.
• Prompt remote access to the settings of shock sensor.
• Prompt remote access to the settings of motion sensor.
• View event history with time and event stamps.
• Automatic control of RF coverage zone.
Base unit
• Dialog coding of control commands sent at a frequency of 868 MHz.
• Individual 128-bit encryption key.
• Event history with exact time stamps is stored in the base unit and is transferred to the remote
when it is in range.
• Can be complemented with BM-103/105 single-wire digital block relay.
• Built-in integral accelerometer for determining motion and shocks with adaptive processing
algorithm and sensitivity controls via the remote.
• Monitoring of on-board voltage.
• Separate inputs for hood and trunk sensors.
• Advanced processing of sensor data, eliminating false alarm possibilities.
• Precision measurement of interior and engine* temperature, displayed on the remote.
• Sequential unlocking of the doors.
• Arming when the engine is running.
• Automatic arming.
• Registers delay for interior lighting when arming.
• Software updates via built-in micro-USB socket.
Table of contents
. System features 3
. System set 4
. Control remotes 5
. LED indicator signals 5
. Quick access functions of the main control remote 6
. Icons of remote 7
. Arming procedure 10
. Disarming procedure 10
. Unlocking the trunk 11
. Timer channels 12
. Locking/unlocking doors when the engine is running 12
. Car search function 13
. Delayed arming (Hands Free mode) 13
. PANIC mode 14
. CHECK mode, monitoring car parameters 14
. Event history 15
. Remote and automatic engine start 15
. Engine preheater 19
. Maintenance/valet mode 19
. System settings menu 20
. Wiring diagram 22
. Wiring description 24
. Remote sensor settings 26
. Leaving connection zone notification settings 28
. Siren signal settings 29
. Silent mode of the remote 29
. Time and alarm clock settings 30
. Checking the number of recorded remotes 30
. Replacing a battery in the remote 30
. Emergency disarming 31
. Changing the factory preset service PIN-code 31
. Changing core settings 32
. Siren sounds and turn light signals 40
. Meaning of indicator LED colors 40
. Glossary of terms 41
. Warranty obligations 42
. Installation certificate 43
. Acceptance certificate 44
. Warranty card 44 * Engine temperature indication is available only if temperature sensor is connected. The sensor availability depends
on the system set.

5
4User manualPandora DXL-0070L service-security system
Ae
rial
LCD
Sound
emitter
Button 1 Button 2 Button 3
SOS alarm button
Send
indicato
r
A
larm
indicato
r
L
ock
indicato
r
Unlock
indicato
r
exact time the event happened. Event history can be read using a remote.
System set
1. Base unit ..................................................................................................................................................... 1
2. Main control remote with LCD ............................................................................................................ 1
3. Supplementary control remote without LCD ................................................................................ 1
4. Main cable .................................................................................................................................................. 1
5. Cable with three-colored light indicator ........................................................................................ 1
6. Cable with VALET button ....................................................................................................................... 1
7. Siren................................................................................................................................................................1
8. LIN interface wire .................................................................................................................................... 1
9. Fastening kit ............................................................................................................................................... 1
10. User installation manual with wiring diagram ............................................................................. 1
11. Relay automatic start module ............................................................................................................ 1
12. Temperature sensor ................................................................................................................................ 1
13. Packaging .................................................................................................................................................... 1
Manufacturer reserves the right to change set and construction of the product to improve its technological
and operational parameters without notification.
Car security zones
Pandora DXL-0070L service-security system guards following independent zones with
corresponding zone notifications on the remote and recording alarms into the event history:
• car doors perimeter (separate for every door)
• front hood triggers
• trunk triggers
• ignition trigger
• brake pedal button
• triggering of the shock sensor (warning level)*
• triggering of the shock sensor (alarm level)
• triggering of the motion sensor
• triggering of the tilt sensor
• critically low on-board voltage
All* alarm events are recorded into system’s non-volatile memory with coordinates, date and
* Triggering of the warning level of shock sensor is not saved in the event history.
Control remotes
WARNING!
ALL CONTROL COMMANDS ARE TRANSMITTED VIA RADIO CHANNEL, FOR MAXI
MUM EFFECTIVENESS AND RANGE IT IS RECOMMENDED NOT TO SHIELD AERIAL
AREA SEE PICTURE WITH FINGERS WHEN USING A REMOTE.
WARNING!
REMOTE IS A UNIFIED CONTROL DEVICE. REMOTE CONTROL FUNCTIONS DEPEND
ON SECURITY SYSTEM MODEL.
LED indicator signals
Red Alarm indicator
• Flashes frequently when any notification.
• Flashes when any alarm notification.
Green Lock indicator
• Flashes occasionally if system is armed.
Red Unlock indicator
• Flashes occasionally if system is not armed.
Red Send indicator
• Flashes occasionally if there is no connection.
Two-way remote is the main mean of
control over the system.
For easily distinguishable notifications
the remote uses 16 ringtones. Each ringtone
matches particular event.
Remote has flashing LED indicators for
additional information.
The remote is fully operational when
shipped. To switch the remote on, press
and hold button for 3 seconds.
‘REMOTE ON’ ringtone will play. Pressing
and holding this button again for 3 seconds
will cause the remote to switch off.

7
6User manualPandora DXL-0070L service-security system
Icons of remote
1 2 3 4 5 6 7 8 9 10 11 12 13 14
282726252423222120
19
18
17
16
15
1. Flashes if there is no connection to the base unit.
2. GSM connection indicator (for systems that are equipped with GSM-modem).
3. Sending command indicator.
4. Handbrake/neutral indicator, Brake pedal security zone.
5. Door security zone. Separate for each door (if there is separate control via digital
bus).
6. Original security system status.
Quick access functions of the main control remote
System disarmed System armed
Engine is running Engine is stopped
(short press) Lock doors without arming Arming with sound
conrmation
Search mode – car will
ash turn signals and
sound horn for 5 seconds
(1 sec.) Arming without sound
conrmation
Search mode – car will
ash turn signals without
any sounds for 5 seconds
(2 sec.) Switch on ignition support
(3 sec.) Switch on programmed
neutral Remote engine start
(short press) Unlock doors Unlock doors Disarming with sound
conrmation
(1 sec.) Unlock doors Disarming without sound
conrmation
(>2 sec.) Switch o ignition support
Switch o ignition when
turbo timer, remote or
automatic engine start
is active
(short press) Switch on LCD lighting (available only on the remote with LCD)
(1 sec.) Unlock trunk (CH1)
(2 sec.) Switch on/o timer channel (CH2)
(3 sec.) Switch on/o remote (available only on the remote with LCD)
+
(short press) PANIC mode
+
(short press)
Arming when the engine
is running with sound
conrmation
Arming in 30 seconds
(Hands Free mode) with
sound notication
+
(1 sec.)
Arming when the engine
is running without sound
conrmation
Arming in 30 seconds
(Hands Free mode) without
sound notication

9
8User manualPandora DXL-0070L service-security system
7. Security mode status (armed/disarmed).
8.
Shock sensor security zone.
- Warning level of the sensor.
- Alarm level of the sensor.
- Warning level zone monitoring disabled.
- Shock sensor monitoring disabled.
9. Trunk security zone.
10. Alarm clock.
11. Fuel left.
12. Car battery voltage, voltage security zone.
13. Interior, engine and exterior air temperature.
14. Numeric indicator. Displays current time.
15. Light signalization (using marker lights, turn signals).
16. Engine operation icon.
17. Motion sensor security zone.
18. Front hood security zone.
19. Locking of the engine enabled.
20. Remote battery level.
21. Engine preheater.
22. Ignition, ignition security zone.
23. Tilt sensor security zone.
24.
Silent mode of the system.
- Warning signals of the system disabled.
- All sound signals disabled.
25. Check current state and access event history.
26. System settings.
27. Silent mode of the remote (MUTE).
28. Car maintenance mode.

11
10 User manualPandora DXL-0070L service-security system
Arming procedure
Arming the system allows monitoring of all security zones, locks the doors and blocks the engine.
To arm the system when the engine is stopped, shortly press button on the remote. The
siren will sound and turn signals will flash once. The remote will play ‘ARMING’ ringtone and security
mode status icon (the lock) will change to:
~~
short
press
doors locking
system arming 1 ash
1 ash
1x
press
and hold
1 sec.
For arming without sound confirmation press for more than 1 second.
If when arming doors, hood or trunk were open, the siren will sound 4 short signals instead of 1,
turn signals will flash 4 times, remote will play ‘WARNING!’ ringtone (after ‘ARMING’ ringtone) and
will show troubled zone.This zone sensor will be disabled at that moment. Sensor will be armed again
in 15 seconds after the zone was set right.
For emergency arming when engine is running, press and hold VALET button for 3 seconds until
the system confirms with red LED indicator flash. A car will be armed in 30 seconds.
Disarming procedure
~~
short
press
press
and hold
1 sec.
doors unlocking
system disarming 2 ashes
2 ashes
2x
To disarm the system, shortly press button on the remote.You will hear 2 short siren sounds
and will see 2 flashes of turn signals. The remote will play ‘DISARMING’ ringtone and security mode
status icon will change to:
For disarming without sound confirmation press button for more than 1 second.
If there were new alarming events during the time system was armed, siren will sound 4 times,
and turn signals will flash 4 times, the remote will sound ‘WARNING!’ ringtone (after ‘DISARMING’
ringtone) and will indicate zones triggered. All recent alarm events can be viewed in the event history.
Unlocking the trunk
~~
press
and hold
1 sec.
To independently unlock the trunk, no matter if the system is armed or not, press button
and hold it for 1 second.
If the system is armed when this action is performed, the trunk will be disarmed, shock and
supplementary sensors of the trunk will be disabled. All the other security zones will remain armed.
If the trunk was not opened in 15 seconds after using‘unlock trunk’command, the system will lock
it again, enable sensors and arm trunk security zone. This will be indicated with 1 flash of turn signals.

13
12 User manualPandora DXL-0070L service-security system
Timer channels
Timer channels (see glossary) control additional or original devices in automatic mode (on
particular events) or directly from the remote.
To activate any timer channel, select icon with short presses of button, then press
shortly. Select channel’s number with short presses of . To switch on any channel, shortly press
or press to switch off.
Press and hold button for 2 seconds to get quick access to Timer channel 2 (CH2).
WARNING!
TIMER CHANNELS CAN BE SWITCHED ON FROM REMOTE ONLY IF SYSTEM SET
TINGS ALLOW IT. TIMER CHANNELS CANNOT BE SWITCHED ON USING QUICK AC
CESS IF ENGINE PREHEATER IS CONNECTED.
Locking/unlocking doors when the engine is running
The system controls doors locking when the engine is running. To lock doors, shortly press
arming button, to unlock doors, press disarming button.
OFF
ON
ACC
doors locking
short
press
doors unlocking
There is an automatic movement lock mode that will lock the doors at the car movement and will
unlock them when the ignition is being switched off. In no less than 5 seconds after the ignition was
switched on, the doors will be locked automatically when the car starts moving, and unlocked when
the ignition will be switched off (programmable). If any door was opened after the ignition had been
switched on, automatic locking will be disabled to prevent locking the keys inside the car.
Car search function
~~
short
press
5 ashes
5 ashes
1x
press
and hold
1 sec.
To easily find your car on a massive parking, shortly press when the car is armed. The system
will sound the siren and flash turn signals 5 times in a row.
To search for car without sound confirmation, press and hold button for more than 1 second.
Delayed arming (Hands Free mode)
~~
short press
Doors locking,
system arming
1 ash
1x
press
and hold 1 sec. 1 ash
30 sec.
+
If when leaving the car you cannot arm it using a remote (you have your hands full), you can use
delayed arming.
To activate this mode, shortly press and simultaneously. LED indicator will turn red,
the system will lock doors and will arm in 30 seconds, the siren will sound and turn signals will flash
once, indicating that the mode is triggered.
To activate this mode without sound confirmation, press and hold both and for
more than 1 second until the sound and vibration signal.
To cancel delayed arming when it is triggered, simply press .

15
14 User manualPandora DXL-0070L service-security system
PANIC mode
+ lights 30 sec.
~~
short press
+
If your car or you are in danger and you want to draw attention to your car, you can use PANIC
mode. In this mode the siren will sound and turn signals will flash repeatedly for 30 seconds. To trigger
PANIC mode, press and simultaneously. To switch it off, press either or .
CHECK mode, monitoring car parameters
short press
~~
select
with presses
Interior temperature
Battery voltage
Engine temperature
Outside temperature
Fuel level
To receive information about engine temperature, interior temperature and on-board voltage,
press button, select icon and shortly press button.
For 10 seconds, numeric indicator will be sequentially showing interior temperature ( ),
engine temperature ( ), outside temperature ( ) and battery voltage ( ). To exit
this mode, shortly press button otherwise it will end automatically in 10 seconds.
NOTE:Temperature will only be shown if temperature sensor is connected. The sensor availability depends
on the system set. Fuel level will only be shown if it can be read from CAN-bus.
Event history Event 1
Event 48
short press
~~
select
with presses
To view event history in the system’s memory, press button and select icon, then
shortly press button.
Navigate several last events using (forward) and (back). Events are displayed by show-
ing time of the event and flashing corresponding trigger zone indicators. To exit this mode, press and
hold for 1 second.
Remote and automatic engine start
The system allows for remote engine start using remote engine start command or automatic
engine start using preconfigured automatic engine start function. Remote start can be used to heat
engine and interior, charge battery or to cool the interior with air conditioning.
Remote and automatic start can only be used when the system is armed.
If the car has manual transmission, remote or automatic start will only occur if programmed
neutral procedure was followed when the car was arming.
Remote and automatic engine start on automatic transmission cars will only occur, if transmission
selector lever was left in a ‘P’position.
When using remote and automatic engine start functions, make sure that the car is secured with
handbrake or some other means of fixating the car on a parking position.
While system is in remote and automatic start mode, it keeps performing all security functions
save for shock sensor, which will have lower sensitivity during engine start and for a short time after
while algorithm adjusts to the new normal. To compensate, motion sensor sensitivity, responsiveness
and range will be increased. If any security zone will be triggered, the engine will be immediately
stopped and alarm mode will be entered. Herewith all immobilizer functions will be activated.

17
16 User manualPandora DXL-0070L service-security system
Programmable neutral procedure (for cars with manual transmission)
xate the car using
a handbrakeleave the car, close the doors
OFF
ON
ACC
short press
in 3 sec. the engine will be
stopped, the system is ready
to perform remote start
‘engine stop’
ringtone
~~
If you are planning to use remote and automatic engine start on a car with manual transmission, before
arming you will need to perform following actions:
1. While the engine is running, fixate the car with the handbrake and put manual transmission lever
(shift-stick) to the neutral position.
2. Turn the key in the ignition lock to the OFF position (the engine should still be running) and take
it out of the lock.
3. Leave the car, close the doors.
4. Press button to arm the car and lock the doors. On LCD remote the engine operation icon
will be spinning and security mode status icon will light.
5. The engine will be stopped. Now the system is ready to perform remote and automatic engine
start.
Remote engine start
If the system is prepared for remote start, to execute it, press and hold for 3 seconds. Sound
signal will confirm the command, LCD will show crossed out shock sensor icon and flashing
engine operation icon signifying preparation to the engine start. In a few seconds the engine
will be started, the remote will play ‘ENGINE START’ ringtone and show spinning engine operation
icon .
Engine operation duration depends on system settings – either heating time or threshold temperature
for engine stop.
3 ashes
‘engine start’
ringtone
press
and hold
3 sec. preparing
to start
engine start ~~
To remotely stop the engine while it performs heating, press and hold for 2 or more seconds.
The engine will be immediately stopped and it will be confirmed by remote playing ‘ENGINE STOP’
ringtone and engine operation icon fading.
‘engine stop’
ringtone
press
and hold
2 sec. engine stop
~~
‘engine start’
ringtone ~~
The remote will give notification 1 minute before designated engine stop: icon will flash and
‘ENGINE STOP IN 1 MINUTE’ ringtone will play every 10 seconds. If the engine was started using
remote or automatic start, remote engine start command will extend its operation period by 10
minutes.
This procedure can be repeated multiple times.

19
18 User manualPandora DXL-0070L service-security system
Automatic engine start
The system allows setting up modes of automatic engine start and stop. Synchronized real-time
clock on the remote and base unit and other autonomous system settings allow many engine start
options without needing to have the remote in command radio range.
2
5
8
4
7
3
6
1
select
with presses
on
o
set autostart
hours minutes
set temperature
increase decrease
set heating time
on
o
on
o
daily timer
autostart by temperature
periodic heating
increase decrease
set stop temperature
on
o
engine stop by temperature
increase decrease
If you have not conrmed with this button press,
remote start settings will remain the same as before.
Automatic start and engine work conditions programming is done using LCD remote. Select
icon by pressing button and press button to enter remote start functions menu. This
menu has 8 sub-levels that can be rotated by pressing . Sub-level values are changed using
and .
When changing settings are done, the values should be saved. To do this, press button. The
changes will be sent to the base unit, confirmed by the double sounding of short sound signal.
NOTE: If you have not saved new settings, remote and automatic engine start settings will remain the same
as before.
- To proceed to the following engine setting level, shortly press button.
- To exit setting mode, press and hold button for 1 second (or it will end automatically in 10 seconds),
herewith changed settings will not be saved.
NOTE: Engine start via temperature is available only if temperature sensor is connected. The sensor
availability depends on the system set.
Engine preheater
To switch on engine preheater, select icon by pressing button and then shortly press
button. Sound notification will confirm reception of the command. If preheater monitoring is
connected and enabled, LCD will display icon during engine preheater operation.
short press
~~
select
with presses Engine preheater started
To switch off engine preheater using a remote, select icon by pressing button and
confirm by shortly pressing button. Sound notification will confirm reception of command. LCD
will display icon.
NOTE: To start/stop the engine preheater immediately, press and hold button for 2 seconds.
Available for the current base unit software.
WARNING!
ONLY ENABLE REMOTE START IF YOUR LOCAL LEGISLATION ALLOWS DRIVERLESS
CARS TO HAVE WORKING ENGINE.

21
20 User manualPandora DXL-0070L service-security system
Maintenance/valet mode
short press Maintenance/valet
mode enabled
~~
select
with presses
1
It is recommended to put system into maintenance mode before handing it to the car service or
valet parking. When this mode is switched on, security system stops interfering with built-in electron-
ics and disables all functions to ease maintenance or parking. Moreover, you will not have to leave the
remote to the valet or the mechanic. Disabling valet mode is not possible without using the remote.
This feature is implemented to prevent recording additional remotes during maintenance without
the owner knowing.
To activate maintenance mode while the engine is running, select icon by pressing
button and confirm by shortly pressing button. The system will confirm enabled valet mode
with green flash of LED indicator when engine is running. To exit maintenance mode, select icon
by pressing button and confirm by shortly pressing button.
* Additional sensors control and GSM interface are not supported by this model.
System settings menu
Main system parameters and settings can be changed using LCD remote. To enter the settings
menu, select icon by pressing button and confirm by pressing button for 1 second. To
cycle between sub-levels of settings, use button, to enter sub-level of settings, press and hold
for 1 second.
If there is no connection to the base unit, LCD will display ‘Err’.
select
with presses press and hold 1 sec.
short press
Shock sensor settings
short press
Additional sensor settings*
short press
Motion sensor sensitivity
settings
short press
Tilt sensor sensitivity settings
Switch On/O GSM-interface*
short press
Leaving connection zone
notication settings
short press
Siren operation settings

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
White
Red/Black
Orange/Black
Yellow/White
Grey
Green
White/Blue
Black
Blue
Brown/White
Orange/Black
Yellow/Black
Blue/Black
Yellow
Purple
Red
3..100V min 8Hz
(–) 200mA
(–) 150mA
(–)
(–) 200mA
(+)
(–)
(–)
(–)
(–) 150mA
(–) 200mA
(+)
(+) 2A
(+) Fuse 3A
TACHOMETER
OUT-5 • OPEN TRUNK
CAN1-HIGH
CAN2-HIGH • OPEN DOORS
INP-2 • DOOR TRIGGERS
OUT-3 • TURN SIGNALS
INP-5 • BRAKES
GROUND
INP-4 • HANDBRAKE/NEUTRAL
INP-3/IMO** • HOOD PIN
CAN1-LOW
CAN2-LOW • LOCK DOORS
OUT-1/INP-1/IMI** • TRUNK TRIGGER
INP-6 • IGNITION SWITCH
OUT-11 • SIREN
POWER +12V
(–)
(–)
(–)
(–)
(–)
+ 12V
OUT-7 • ENGINE BLOCK
OUT-6 • ACCESSORIES
OUT-9 • IGNITION
OUT-8 • KEYLESS BYPASS
OUT-10 • STARTER
POWER +12V
1
2
3
4
5
6
Blue
Orange
Brown
Green
Yellow
Red
Blue/Black
Green/Black
Blue/Red
Blue
Green/Red
Green
Orange
Yellow
Brown
Red Fuse 40A
RELEY MODULE
RMD-5
TEMPERATURE SENSOR
DS1820*
X-4 Main socket
1
2
White
Black
LIN IN
LIN OUT
X-1 Engine Preheater
X-6 LED indicator
X-7 VALET button
X-3 Temperature sensor
X-2 micro-USB
X-5 Relay module
R3
R2
R1
R5
R4 20A
20A
20A
20A
20A
VALET
BUTTON
LED
INDICATOR
VALET
BUTTON
WARNING!!!
For proper installation a connected laptop with AlarmStudio
software is required. Switch the system to programming mode
(see page 33) and select your car model in AlarmStudio for
detailed installation instructions. AlarmStudio can be
downloaded from pandorainfo.com
WARNING!!!
Total current relay R1 + R2 + R3 should not exceed 40A!
ANTENNA
868 MHz
!
Pandora
MODEL: DXL-OO7OL
WARNING!
Do not accidentally
shield the antenna!
* See ‘System set’on page 4
** Connect when keyless start function in Toyota, Lexus is
enabled

25
24 User manualPandora DXL-0070L service-security system
Wiring description
X-4 socket (main)
Wire 1 (White) (tachometer input) It is analog input that should be connected to wire of
tachometer or signal wire of injector, a wire with stable impulses of any polarity that correspond with
motor shaft rotation frequency.
Wire 2 (Red-black) (OUT-5) Factory setting is ‘Open trunk’. Negative output of additional channel
with maximum load capacity 200mA. This output is multipurpose, it can operate in accordance with
selected logic.
Wire 3 (Orange-black) (‘CAN-High’) It connects to appropriate CAN-High wire of the car.
Wire 4 (Yellow-white) (OUT-4) Factory setting is ‘Open central lock’. A negative impulse of 0,8
seconds is formed on the wire to open central lock. Channel operation logic can be set in the output
table. The channel OUT-4 will stop working as output when car code that supports CAN2 is selected.
Wire 5 (Grey) (INP-2) Factory setting is ‘Door switches’. This wire connects to a wire that becomes
grounded when the door opens. This input is multipurpose, it can operate in accordance with
selected logic.
Wire 6 (Green) (OUT-3) Factory setting is ‘Control turn indicators’. This wire connects to the hazard
flashers button. Negative output of additional channel with maximum load capacity 200mA. This
output is multipurpose, it can operate in accordance with selected logic.
Wire 7 (White-blue) (INP-5) Factory setting is‘Brake On/Off switch’. This wire connects to the brake
pedal button where 12V voltage appears when the pedal is pressed (stop lights wire). Brake pedal
signal is one of the system’s security zones. This input is multipurpose, it can operate in accordance
with selected logic.
Wire 8 (Black) (ground) It should be connected to the car body in a grounding spot. This wire
should be connected FIRST during installation.
Wire 9 (Blue) (INP-4) Factory setting is ‘Neutral/Handbrake’. This wire connects to appropriate wire
of the car (preferably handbrake button).This input is multipurpose, it can operate in accordance with
selected logic.
Wire 10 (Brown-white) (INP-3) Factory setting is ‘Front hood limit switch’. This wire connects to
appropriate wire that becomes grounded when the front hood opens. This input is multipurpose, it
can operate in accordance with selected logic.
Wire 11 (Orange-black) (‘CAN-Low’) It connects to appropriate CAN-Low wire of the car.
Wire 12 (Yellow-black) (OUT-2) Factory setting is ‘Close central lock’. A negative impulse of 0,8
seconds is formed on the wire to close central lock. Channel operation logic can be set in the output
table. The channel OUT-4 will stop working as output when car code that supports CAN2 is selected.
Wire 13 (Blue-black) (OUT-1/INP-1) Factory setting is ‘Trunk limit switch’. This wire connects to
appropriate wire that becomes grounded when trunk opens. This output is multipurpose, it can
operate as input or output in accordance with selected logic. The channel can be assigned as IMI
output for keyless bypass of immobilizer (connects according to installation map).
Wire 14 (Yellow) (INP-6) Factory setting is ‘Ignition’. This wire connects to ignition switch or to
appropriate wire where 12V voltage appears when ignition is enabled and doesn’t disappear until the
moment ignition is disabled. This input is multipurpose, it can operate in accordance with selected
logic.
Wire 15 (Purple) (‘siren’) It connects to siren control wire (+) (maximum load current is 2A). This
channel is multipurpose, it can operate as input or output in accordance with selected logic.
Wire 16 (Red) (‘Power supply’ 12V) It should be connected to reliable conductor with constant
voltage of 12V.
X-5 socket (start relay module)
Wire 1 (Blue) (OUT-7) Factory setting is ‘N.O. blocking’. The channel is used to control blocking
relay with normally open logic (it becomes grounded when switching on the ignition and security
system is not armed). A negative output of additional channel with maximum load capacity 200mA.
This output is multipurpose, it can operate as input or output in accordance with selected logic.
Wire 2 (Orange) (OUT-6) Factory setting is ‘Accessories’. The channel is used to control accessories.
If ‘Car with START/STOP button’setting is enabled, the channel will control brake pedal during remote
or automatic engine start. A negative output of additional channel with maximum load capacity

27
26 User manualPandora DXL-0070L service-security system
Remote sensor settings
Shock sensor control and sensitivity settings
For prompt remote adjustment of alarm and warning levels of the shock sensor enter the settings
menu, select icon with button presses and press button for 1 second. Press
button to cycle between control and sensitivity settings of warning and alarm sensor levels.
icon and left part of the numeric indicator will flash indicating that alarm level of shock
sensor is being adjusted. Short presses of button will increase the sensitivity of the alarm
level (i.e. sensor will trigger from smaller impacts), short presses of button will decrease the
sensitivity of the alarm level of the shock sensor.
200mA. This output is multipurpose, it can operate as input or output in accordance with selected
logic.
Wire 3 (Brown) (OUT-9) Factory setting is ‘Ignition’. This output is used to switch on ignition. It
allows for automatic engine start, turbo timer, ignition support and connecting to ignition in the
break. If ‘Car with START/STOP button’setting is enabled, the channel will operate in impulse mode to
control the button. A negative output of additional channel with maximum load capacity 200mA. This
output is multipurpose, it can operate as input or output in accordance with selected logic.
Wire 4 (Green) (OUT-8) Factory setting is ‘Bypass’. Output activates during remote or automatic
engine start. A negative output of additional channel with maximum load capacity 200mA. This
output is multipurpose, it can operate as input or output in accordance with selected logic.
Wire 5 (Yellow) (OUT-10) Factory setting is ‘Starter’. This output is used to switch on starter of
the car. A negative output of additional channel with maximum load capacity 200mA. This output is
multipurpose, it can operate as input or output in accordance with selected logic.
Wire 6 (Red) It is relay module power supply 12V.
Shock sensor settings
Control settings
press
and hold
1 sec.
or
Shock sensor
enable
Shock sensor
disable
Control over warning
area of the shock
sensor disabled
increase
decrease
Save
setting
s
short
press short press
Warning levelAlarm level
increase
decreaseshort
press
Sensitivity settings
Short presses of button will switch between sensitivity settings of warning and alarm levels
of the shock sensor. To save the new sensitivity values of the shock sensor, shortly press . To exit this
mode without saving, press and hold button for 1 second, otherwise it will end automatically in
10 seconds.
Max sensitivity value of warning and alarm level of sensors is 50.
Motion/tilt sensor sensitivity settings
Sensitivity settings
increase
decrease
Save
setting
s
Alarm level
short
press
press
and hold
1 sec.
or
For prompt remote adjustment of alarm and warning levels of the motion/tilt sensor enter the
settings menu, select icon with button presses and press button for 1 second.

29
28 User manualPandora DXL-0070L service-security system
Siren signal settings
To configure siren sounds, enter the settings menu, select icon by pressing button.
Select one of three siren sound options using or .
To exit this mode and save, shortly press button, to exit without saving, press and hold
button for 1 second or it will end automatically in 10 seconds.
All sound signals are enabled
Warning notifications are disabled
All sound signals are disabled
select
with presses
~~
select
with presses all signals disabled
3
Silent mode of the remote
This function disables all sound signals of the remote, this mode does not apply to alarm clock
and main zones triggering. LED indication and vibration remain enabled.
To set silent mode of the remote, select icon by pressing button.
This function can be set using button (all sound signals are disabled) and button (all
sound signals are enabled).
icon ashing,
sound notications disable
d
icon faded,
sound notications enabled
select
with presses
short
press
~~
~~
1
To save the new sensitivity values of the tilt sensor, shortly press . To exit this mode without
saving, press and hold button for 1 second, otherwise it will end automatically in 10 seconds.
Max sensitivity value of motion and tilt sensors is 50.
Leaving connection zone notification settings
When the owner with the remote leaves the range of system’s radio connection, there are three
possible notification options. To set up one of the options, enter the settings menu, select icon
by pressing button and confirm by pressing for 1 second. With short presses of or
select one of three notification options:
1. disable notifications;
2. enable notification with ‘SIGNAL LOST’ ringtone;
3. enable notification with alarm signals.
To exit and save the new settings, press button.To exit this mode without saving, press and hold
, otherwise the menu will be exited automatically in 10 seconds.
Leaving connection zone
notication settings Mode settings Save
settings
press
and hold
1 sec.
or
Notications
disable
Notication
with alarm signals
Notication
with ‘signal lost’
ringtone
short
press

31
30 User manualPandora DXL-0070L service-security system
• take the battery out and place a new one on its place;
• the remote is ready for use (switch it on by pressing and holding for 3 seconds).
It is recommended to keep an extra AAA battery in the car.
Emergency disarming
In case you cannot disarm the system using a remote, use special service PIN-code:
Factory preset PIN-code is 1-1-1-1. Use VALET button to input PIN-code.
Entering PIN-code is available only if the ignition is switched off.
1. Using VALET button, input the first digit of the code
(press the button a number of times, equal to the first digit;
pauses between presses should not exceed 1 second). The
system will confirm with red LED indicator flash.
2. Similarly input second, third and fourth digit. Every input
will be confirmed with red LED flash.
3. The system will confirm correct PIN-code with red and green flashes of LED indicator. If the input
was incorrect, it will be indicated with long red flash. New input can be attempted after 5 seconds.
4. If the system was armed, it will be disarmed after entering the correct PIN-code.
If the system is disarmed and the engine is stopped, after entering PIN-code the system will enter
programming mode.
WARNING!
FACTORY PRESET PINCODE IS 1111. PLEASE REMEMBER TO CHANGE PINCODE,
SEE PAGE 31.
Changing the factory preset service PIN-code
To improve the protection of the system, we recommend you to change service PIN-code.
1. Disarm the system, switch off the ignition.
2. Using VALET button, input service PIN-code. Factory preset PIN-code is 1-1-1-1.
3. Using VALET button, input the first digit of the service code (press the button a number of times,
VALET
button LED
indicator
Time and alarm clock settings
Time settings
To set up time, select clock icon with button presses. With short presses of set hours,
with short presses of set minutes. Longer presses of buttons and will cause numbers
to rotate faster.
To proceed to setting alarm clock, shortly press button, to exit this mode, press and hold
button for 1 second, otherwise it will be exited automatically in 10 seconds.
Alarm clock settings
To set up the alarm clock, select icon with button presses, this icon will start flashing.
or will be displayed on the numeric indicator. With short presses of and set alarm
clock mode: (enabled) or (disabled). To proceed to setting alarm clock time, shortly press
button.
Checking the number of recorded remotes
Number of recorded remotes can be checked every time the ignition is switched on when
disarmed. Number of orange LED flashes will indicate the number of recorded remotes.
Number of recorded remotes can also be checked by taking off and putting back on battery
terminal. The system will sound the siren several times, equal to the number of recorded remotes.
Replacing a battery in the remote
1
Battery ААА
2012
MN2400
LR03 1.5V
If high quality batteries are used, service-security
system remote can function up to 4 months without
needing a replacement. Battery needs to be replaced
if the remote is not turning on or the icon has
only one bar left and starts flashing.
To replace the battery:
• move battery cover lock in the direction shown
with arrow;

33
32 User manualPandora DXL-0070L service-security system
If base unit has not yet been installed in the vehicle, it should be powered via micro-USB cable while
programming. To program using a computer connected via cable, you need a standard micro-USB
cable, a computer with Windows and a special piece of software – Pandora AlarmStudio.
AlarmStudio can be downloaded from the official company web-site pandorainfo.com
In preparation to the programming, following stages should be followed:
– connect micro-USB cable to any free USB socket of the computer;
– start Pandora AlarmStudio (can be downloaded from the web-site);
– enter the programming settings mode by entering the service PIN-code on the base unit using
VALET button. Factory preset PIN-code is 1-1-1-1.
Entering programming menu, PIN-code input:
1. Disarm the system, switch off the ignition.
2. Connect the base unit of the system to a computer via micro-USB cable (X-2 socket).
3. Using VALET button, input service PIN-code. Factory preset PIN-code is 1-1-1-1.
4. Using VALET button, input the first digit of the service code (press the button a number of times,
equal to the first digit; pauses between presses should not exceed 1 second). The system will confirm
entering of the first digit with red LED indicator flash.
5. Similarly input second, third and fourth digit. Every input will be confirmed with red LED flash.
6. The system will confirm correct PIN-code with red and green LED flashes and proceed to the
programming mode. If the input was incorrect, it will be indicated with long red flash and the system
will proceed to previous mode. New input can be attempted after 5 seconds.
Changing core settings using VALET button
1. Using VALET button, input the desired level number (press the button a number of times, equal
to this number; pauses between presses should not exceed 1 second).
The system will confirm correct input with red LED flashes and short siren signals and proceed to
the desired level. If the input was incorrect, the system will not confirm input and will await a new level
input after a series of green and red flashes.
2. While changing the settings of levels 6 – 21, move from selected level to the next one by shortly
pressing VALET button. The system will confirm moving to the next level with short siren signals. The
number of signals corresponds with selected level number.
3. When one of levels 6 – 21 is selected, indicator LED will display current state of the selected level
with red or green light. Setting is changed with or :
equal to the first digit; pauses between presses should not exceed 1 second). The system will confirm
entering of the first digit with red LED indicator flash.
4. Similarly input second, third and fourth digit. Every input will be confirmed with red LED flash.
5. The system will confirm correct PIN-code with red and green LED flashes and proceed to the
programming mode. If the input was incorrect, it will be indicated with long red flash and the system
will proceed to previous mode. New input can be attempted after 5 seconds.
6. To proceed to setting service PIN-code press VALET button twice. The system will confirm with
double siren signal and double LED red flashes.
• LED indicator is not lit. Press VALET button a number of times, equal to the first digit. LED will
flash orange for every press. Pauses between presses should not exceed 1 second;
• the system will confirm input of the first digit with red LED flash;
• similarly input other digits of PIN-code;
• the system will confirm with red and green LED flashes;
• input PIN-code again;
• if the double input of new service PIN-code was correct, the system will confirm it with LED
indicator red and green flashes, new code will be recorded, the system will enter programming mode;
• if the input was incorrect, it will be indicated with red flash and the system will enter programming
mode.
When you finished inputting PIN-code, LED indicator will be faded and the system will wait for
new level input.
WARNING!
PLEASE WRITE DOWN YOUR NEW PINCODE ON PAGE 31.
Changing core settings
Changing core settings via computer
The system allows programming all settings and updating software of the base unit via the
interface micro-USB cable or via radio channel using a computer. It does not matter, whether base
unit is installed into a vehicle or not. Software reads the current setting and allows changing them.

35
34 User manualPandora DXL-0070L service-security system
Most of the times button is ‘enable’ (LED lights green), button is ‘disable’ (LED lights red).
To exit programming mode and save the settings, switch on the ignition at any stage of programming
(except stages that require you to switch on ignition during programming process).
Level 1– Recording remotes into the system’s memory
Enter the first level of programming. Remotes are recorded (paired) one by one. To pair the
remote, press three buttons simultaneously (on the remote) and hold them for 1 second (until a short
beep for the LCD remote; until the LED fades for the additional remote), then release the buttons. If
the recording was successful, LCD remote will emit 2 short beeps and the base unit will emit 1 beep,
after that you can move to recording the next remote. The pause between recordings of remotes
should not exceed 20 seconds.
To finish the recording of the remote units into the system, VALET button should be pressed again,
the status LED will produce series of red and green flashes; then switch on and off the ignition to leave
the programming mode.
Level 2 – Changing the factory preset service PIN-code
• Indicator LED is not lit. Press VALET button the number of times equal to the first digit of the
security code. Each pressing of VALET button is followed by orange flash of the indicator. The interval
between presses should not exceed 1 second.
• The input will be confirmed by red flash of indicator.
• Enter the other numbers in the same manner.
• The fourth number input will be confirmed by series of red and green LED indicator flashes.
• Enter all four numbers again.
• If you were able to correctly enter code twice, the indicator will produce series of red and green
flashes and a new PIN-code will be recorded, the system will return to the programming mode.
• In case of the incorrect code input the indicator will flash red and the system will return to the
programming mode.
After the input is complete, the indicator goes out, the system awaits a new programming level
input.
Level 3 – Recording the idle speed to the system’s memory
At this programming level the idle turns speed of the engine is recorded (into non-volatile
memory). Upon entering this level you need to switch the ignition on and start the engine (it should
be warmed-up and the idle speed should match a normal rate for the pre-heated engine). Wait until
Name of function
LED indicator
Red • Button 2 Green • Button 1
Level 1 Recording remotes into the system’s memory
See description of levels
Level 2 Changing the factory preset service PIN-code
Level 3 Recording the idle speed to the system’s memory
Level 4 Resetting to factory settings
Level 5 Selecting car model
Level 6 Transmission type (manual or automatic) Manual transmission Automatic
transmission
Level 7 Engine operation control Tachometer Dashboard indicator
Level 8 Tachometer signal source CAN Tachometer Analog tachometer
Level 9 Ignition connection type In series Parallel
Level 10 Turbo timer Disabled 120 sec.
Level 11 Delay before starter is enabled Gas (2 sec.) Diesel (15 sec.)
Level 12 Switching on N.C., N.O. blocks Disabled Enabled
Level 13 Locking doors when on movement start and unlocking
doors when ignition is switched off Disabled Enabled
Level 14 Re-arming Disabled Enabled
Level 15 Delay of doors triggers arming (for interior lighting) 0 sec. 45 sec.
Level 16 Additional locking command after ignition
is switched off when armed Disabled Enabled
Level 17 Turn signals control Direct Button
Level 18 Control over hazard lights Potential Impulse
Level 19 Control over original security system Disabled Enabled
Level 20 Disarming original security system before remote start Disabled Enabled
Level 21 Setting up keyless bypass of built-in immobilizer See description of levels

37
36 User manualPandora DXL-0070L service-security system
the stable idle speed is reached (it takes about 30 seconds). Then press VALET button once. Successful
recording of the idle speed will be confirmed with 1 beep. The ignition should be switched off after
recording. While on this programming level, you can start and stop the engine many times – it will
only be exited on VALET button press.
Level 4 – Resetting to factory settings
To reset to the factory settings, you need to enter fourth programming level, then press and hold
VALET button for 3 seconds until siren sound. Once VALET button is released, the status indicator will
confirm a successful reset to factory settings with a long red flash.
Level 5 – Selecting car model
On this level car model can be selected from a pre-programmed list in the built-in multisystem
CAN adapter.
Car model is represented here as four digits 1 to 9, the first two digits indicate car makes, the next
two digits indicate models.
Enter this level (to enter level 5, press VALET button 5 times after moving to the programming
mode) to select car model:
• Status LED is not lit. Press VALET button the number of times equal to the first digit of the
car model. Each pressing of VALET button is followed by orange flash of the indicator. The interval
between the presses should not exceed 1 second;
• Enter the other numbers in the same manner.
When finished selecting of a car model, the system will return to the programming mode. LED
indicator will confirm CAN-bus activity by series red and green flashes.
The list of supported car models and additional information is on the official company web-site
pandorainfo.com
Level 6 – Transmission type (manual or automatic)
The factory preset is manual transmission. To enable remote (or automatic) start, perform
the programmable neutral procedure (see page 16), which normally means activating handbrake
while engine is still running. If automatic transmission is selected, automatic start will be enabled
whenever the system is armed. Herewith neutral/handbrake limit switch will be checked while
attempting to start engine.
Level 7 – Engine operation control
The factory preset is tachometer. The system monitors if there are tachometric signals by
analog input or by digital CAN-bus, depending on level 8 settings. To monitor engine operation by
tachometer, it is necessary to register idle turns speed on the level 3. ‘Dashboard indicator’ option
disables monitoring of tachometric signal and enables the control of engine operation by analog
dashboard indicator input. Starter operation will be stopped when selected dashboard indicator
(e.g. battery or oil pressure) fades during remote start.
Level 8 – Tachometer signal source
The factory preset is tachometer CAN. This setting allows the system to read tachometer signals
from digital CAN-bus. For analog input it is necessary to change this setting to tachometer analog.
Level 9 – Ignition connection type
The factory preset is parallel. The setting determines logic of ‘Ignition’ channel (wire) operation.
If the setting is changed to in series, the system will block switching ignition on when armed. When
ignition is connected in series (by incut), control is performed via analog input; control by CAN will
be disabled.
WARNING!
IF LED INDICATOR DOES NOT CONFIRM CANBUS ACTIVITY BY GREEN FLASHES
AFTER CAR MODEL WAS SELECTED, LOCK AND UNLOCK DOORS TO WAKE THE
BUS. DO NOT SWITCH ON IGNITION! IT CAN MAKE SYSTEM EXIT A PROGRAMMING
MODE. IF LED INDICATOR DOES NOT CONFIRM CANBUS ACTIVITY BY GREEN
FLASHES AFTER WAKING THE BUS, CAR MODEL SELECTION WAS DONE INCOR
RECTLY  THE SYSTEM DOES NOT RECOGNISE DIGITAL BUS. TRY TO REPEAT INPUT
OF CAR MODEL CODE.
WARNING!
IN CASE CAR MODEL DIGITAL CODE YOU ENTERED DOES NOT EXIST, LED INDICA
TORWILL PRODUCE SERIES OF RED AND GREEN FLASHES SAME AS IF CAR MODEL
SELECTION WAS CORRECT AFTER INPUT WAS DONE, BUT DEFAULT CAR MODEL
11 11 WILL BE SELECTED. BE WARNED, THERE IS NO WAY OF TELLING IF INPUT
WAS INCORRECT.

39
38 User manualPandora DXL-0070L service-security system
Level 10 – Turbo timer
The factory preset is disabled. This level determines time the engine will keep running after the
ignition lock was turned to OFF with a key. Turbo timer will be activated only if engine was running
with a key for more than 1 minute and neutral/handbrake input registered a change (i.e. only after
actually riding a car).
Level 11 – Delay before starter is enabled
The factory preset is 2 seconds. Using this setting, period of switching electronics on before
engine start can be extended to heat spark or glow plugs.
Level 12 – Switching on N.C., N.O. blocks on movement start
The factory preset is disabled. If this level is enabled, channels, which are set as Normally Closed
and Normally Open engine blocks, will only be activated when car movement is registered by the
base unit.
Level 13 – Locking doors on movement start and unlocking doors when ignition
is switched off
The factory preset is disabled. If this level is enabled, the system will close the central lock of the
car on movement start and will open it when ignition is switched off.
Level 14 – Re-arming
The factory preset is disabled. When enabled, re-arming will commence in 30 seconds, if doors
were not opened or ignition was not switched on (i.e. the system was disarmed accidentally). When
the system is re-arming, closing impulse is issued to the central lock.
Level 15 – Delay of door triggers arming (for interior lighting)
The factory preset is disabled. If this setting is enabled, the system will ignore the state of door
triggers when arming for 45 seconds.
Level 16 – Additional locking command after ignition is switched off when armed
The factory preset is disabled. This setting allows to send additional closing impulse after engine
was stopped when the system is armed. If this setting is enabled, impulse will be sent to the ‘close
central lock’wire when engine is stopped after any kind of remote start (remote start, automatic start,
turbo timer, ignition support and programmable neutral).
Level 17 – Turn signals control
The factory preset is button. This level allows to select control option for turn signals. The system
simulates press of ‘Hazard lights’ button. The wire of designated channel should be connected in
parallel to hazard lights button. Selecting direct control, the system will operate using direct control
over turn signals, sending impulses equal to the number and duration of required flashes.
Level 18 – Control over hazard lights
The factory preset is impulse. This setting simulates button operation without fixing it in pressed
position. Turn signals are switched on and off with impulses. When potential is setting, it simulates
button operation with fixing it in pressed position. Original logic of hazard light button is used: turn
signals flash while button is in pressed position.
Level 19 – Control over original security system
The factory preset is disabled. If this setting is enabled, alarm will take control over original
security system using digital buses of the car.
Level 20 – Disarming original security system before remote start
The factory preset is disabled. If this setting is enabled, before remote or automatic engine start,
original security system will be disarmed by digital bus of the car (after original security system is
disarmed, the system will send a command to lock doors).
Level 21 – Setting up keyless bypass of built-in immobilizer
This level enters programming mode to teach algorithmic keyless bypass of built-in immobilizer.
LED indicator will be lit green when on this level. If system installation was performed correctly on
successful engine start using a key, LED indicator will flash green and siren will emit a short signal. To
save and finish, press VALET button. Now the system should be able to simulate key for remote starts.
For more in-depth instructions, use AlarmStudio.