ParaBody 887101 User manual

Serious Steel
887101 LAT OPTION
I I
ASSEMBLY. INSTRUCTIONS "
Pan # 6802501 1RmA.sion:3/23/99

I IMpORTANT".NOTESI
WELCOMETO THE WORLD OF ~t~il~$ ~t~t~!
Please note:
* Thankyoufor purchasingthe Parabody887101LATOPTION.Please read these instruction~
thoroughlyandkeepthemfor future reference. Thisproductmustbe assembledona flat, lev:
surfaceto assureits properfunction.
Werecommendcleaning your product(pads andflame) on a regular basis, using warmsoapy
water. Touch-uppaint canbe purchasedfromyourParabodycustomerservice representative
at [phone].
Thereis a risk assumedbyindix4dualswhouse this typeof equipment.Tominimizerisk, please
followtheserules:
1. Inspectequipmentdaily. Tightenall looseconnectionsandreplacewornparts immediately.
Failureto dosomayresult in seriousinjury.
2. Donot allowminorsor children to playon or aroundthis equipment.
3. Exercisewithcareto avoidinjury.
4. If unsureof properuseof equipment,call yourlocal Parabodydistributor or call the
Parabody customer service department at [phone].
5. Consulta physicianbeforebe~nninganyexercise program.
[ ToolsRequiredfor Assembly[
*3/4" wrench
*9/16"~vrench
*Ratchetwith3/4" and9/16"sockets
*Adjustablewrench
* Tapemeasure
IBolt Length Ruler [
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER: BOLT LENGTH
Ol I I I I I I I I I I "I
I 1/2
2

KEY
1
2
3
4
5
16
17
18
19
PART# DESCRIPTION
6800203 UPRIGHT
~(X)602 ADJ FOOTSUPPOlZT
6800803 PUI I .h’5[HOUSING
6801003 TOP BOOM
6801102 LATBAR SUPPORT"’
6759802 ~ARRIAGE
6274402 LOW ROW BAR
6725302 LATBAR’
3116201 3-1/2"PUI1 Fry
3116101
3103102
6140701
6405201
3116001
6177001
3119301
4-1/2" PL7J EY
115-1/4" CABLE
121-3/4" CABLE
3X2"END CAP
1XS" GRIP
1 X1" t~ J’DE
2" SQ. ENDCAP
1-1/4" SQ. RUBBER.BUMPER
2-1./2 X 5-1/2" NON-SKIDSTRIP
2-1/2" ROUNDENDCAP....
PARTS LIST
1 ’20
122
I23
124
125
I27
5 28
1 29
13O
2 32
4’J3’
834
2 35
136
237
238’
PART# DESC’R1PTION
’623670’i 1-3/4" SQ.:ENDCAP
6412001 SPRING P ~ SEMBLY
32033’01 VINYLCAP
6416601
3102943
3102502
3102801
3102917
3102807
3102501
3/16X I-3N X5-1/4" PLATE
3/4’X 1-112" GLIDE
1/2X3I/2"BOLT
m"sr~.
3/8" LOWHE
1/2" l ),UK.NUT
1/2 28 4" BOLT
3HTLOCKNUT
SHEK
3/8"L ?CKNIYr
3102922’ 3/8X 2-3/4" BOLT
6480301 3/8"Fl.,,~d IE SPACER
3103801 5/16" SNAPHOOK
3102933 3/8 X OLT
3108102 1/4" QUICKLINK
6075906 12 i/~ CHAIN
31029O6 3/8 X )LT
!i’,’..~’L~., ~ 7/16" CAP
PLUG
STEP1:
¯ Remove four 7/16" CAPPLUGSfrom the UPPER&LOWERCROSSSUPPORTSonthe 888 SMITHMACH/NEas shownin FIGURE1
3

FIGURE 2
LOWERCROSS SUPPORT
3/8" LOW HEIGHT LOCK N-U’T ~
STEP2:
¯NOTE:It may be necessar.~. to loosen the 1/2 X3-1/4" BOLTSof the LOWERCROSSSUPPORTconnecting the UPRIGHT
FIL~.MEbefore beginning STEP2.
¯ Attach four 314 X1-1/T’ GLIDES(24) to the inside_ of the tube on the UPRIGHT(1) as sho~ in FIGURE2 using tI~e follow-
~ngsteps:
¯Thoroughlyclean all surfaces wherethe 3/4 X1-1/2" GLIDES(24) are to be attached.
"- Remo’,~the 3/4 X1 - 1/2" GLIDES( 24) fromthe paperbackingandfirmly applythemto all sho~aasurfaces.
¯ SECURELYassembleone SPRLNGP~qASSENfl3LY(21) to the spring pin barrel on the UPRIGHT(1): See FIGI~q~E
¯LOOSELYassemble thePU! I EYHOUSING(3) and the UPRIGHT(1) to the LOWERCROSSSUPPORTusing m-o 318 X 4" BOLTS
(38), four 3/8" WASHERS(30), and two 3/8" LOWP~IGHTLOCKNUTS(29). See FIGURE
¯SQ. ENDCAP(16) into the end of the PULLEYHOUSING(3) as shownin FIGUREInsert one2"
¯ ..... I-,..... ,,, I, :,

FIGURE
STEP3:
¯Insert two 2-1/2’ ROUNDENDCAPS(19) into the ends of the .ADJ. FOOTSUPPORT(2) as shownin FIGURE
¯Insert one I-3/4" ENiDCAP(20) into the end ofthe ADJ.FOOTSUPPORT(2) as shownin FIGURE
¯Applym’o 2-1/2 X 5-1/2" NON-SKIDSTRIPS(18) to the ADJ.FOOTSUPPOKI"(2) as sho~nin FIGL~q.E
¯Attach four 3/4 X 1-I/2" GLIDES(24) to the outside of the .4~DJ FOOTSUPPORT(2) and four GLIDESto the inside of the
tube on the UPRIGHT(1) as showrt in FIGURE3 using the follo~ng steps:
¯Thoroughlyclean all surfaces wherethe 3/4 X1-112"GLIDES(24) are to be attached.
¯Removethe 3/4 XI o 1/2" GLIDES(24) fromthe paper backingand firmly applythemto all show~lsrxfaees.
¯ Pull back on the SPRINGPIN(21 ) andCAREFIILLYinsert the ADI. FOOTSUPPOKr(2) into the UPRIGHT(1) as shownin FIGURE3.

FIGURE 4
//
STEP 4:
¯ Attacheight 1X1" GLIDES(15) to the ends the CARRIAGE(6) as sho~lin FIGURE4 using the follo~4ngsteps:
¯ ThorougltlycleanMlsurfaceswherethe 1 X1" GLIDES(15)are to be attached.
¯Removethe 1 X1" GLIDES(15) from the paper backing and firmly apply" them to all sho~-n surfaces.
¯ Attach one 1-1/4" SQ. RUBBERBUN~PER(17) to the underside of the angle on the CAP,~AGE(6) as shown in FIGURE
FIGURE
STEP 5:
¯ CAREFULLYslidethe CARRIAGE(6) over the UPRIGHT(1) as sho,~,minFIGURE
¯ Insert one3 X2" ENDCAP(13) imothe endoft.he UPRIGHT(1). SeeFICAJRE
011I3 4

FIGURE 6
l/2 X4"
SUPPORT
STEP 6:
¯ NOTE:It maybe necessary to loosen the 1/2 X3-1/4" BOLTSof the UPPERCROSSSUPPORTconnecting the UPRIGITr
FRAMEbefore beginningSTEP 6.
¯ LOOSELYassemble the TOPBOOM(4) to the UPKIGHT(1) using one 1/2 X 4" BOLT(28), one 112 X 3-1/2" BOLT(25),
"97
~VASHERS(26), and one 1/2 LOCKNL-I-S (.,) as sho~t in FIGURE
¯ LOOSELYassemble the TOPBOOM(4) to the UPPERCROSSSUPPORTusing t~vo 3/8 X4" BOLTS(38).~ four 3/8"’ WASHERS
and two 318" LOCKNUTS(31). See FIGURE
¯Insert one 3 X 2" ENDCAP(13) imo the ~d of the TOPBOOM(4). See FIGURE
SECURELYtighten all connections madeup to this point.
FIGURE 7

FIGURE 8
3/8x
STEP 8:
¯ Routethe 115-1/4" CABLE(l l) through the TOPBOOM(4) as sho~vnin FIGURE
¯ SECL’RELYassemblethree 3-1/2"" PI]LIEYS(9) into the slots of the TOPBOOM(4) using three 3/8 X2-3/4" BOLTS(32), six
SPACERS(33), and three 3/8" LOCKN~’TS(31) as sho~.n in FIGLrRE8. (NOTE:Makesure the cable is routed over "all the pulleys.)

FIGURE 9
STEP 9:
¯Attach the CABLE(11) fromthe TOPBOOM(4) to the CARRIAGE(6) using one1/4" QUICKLINK(36) as shm~alFIGURE 9.
(I/~[PORTAN-~.Secureb" lighten QUICKLINK.)
¯Place one3-1/2" pLrLLEY(9) into the loopof the CABLE(12) belowthe secondandthird PULLEYof the ~FOPBOOM(4) as
in FIGURE9.
LOOSELYassembletwo3/16X1-3/4 X5-1/4"PLATES(23) to eachside of the 3-1/2" PULLEY(9) usingone318X2" BOLT(35),
two318"WASI-IERS(30), andone3/8" LOCKNUT(31). SeeFIGURE

FIGURE 10
STEP 10:
Route the threaded end of the 121-3/4" CABLE(12) through the slot oft.he PULLEYHOUSINGthen SECURELYassemble one 4-1/2
pLrLLEY(10) to the PU~.I.EYHOUSLNG(3) using t~vo3/8X2-3/4"" BOLTS(32), two3/8"" FLANGESPACERS(.: 3), two3/8"" \\:-kSHERS
(30), and two 3/8" LOCKNUTS(31). (NOTE:CABLE (12)should be routed benveen the pulley and the retaining bolt as shown
FIGURE10.)
10