ParaBody 781 User manual

1
781 SWIVEL CABLE KIT
1CLASSH
PART # 7123201
REV.A
Version: 781101
Revision: 05/23/01
USER’S GUIDE
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.

2
PARTS LIST
PART #
7118508
7122101
KEY
1
2
QTY
1
2
KEY
3
4
PART #
3102514
3102955
DESCRIPTION
3/8” SAE WASHER
3/8 X 4-1/4” BOLT
QTY
4
2
DESCRIPTION
GUIDEBRACKET
CABLE
FIGURE 1
• Remove PULLEY and PULLEY BRACKETfrom the 777 GYM SYSTEM. Discard the PULLEY BRACKET. See FIGURE 1.
STEP 1:
3/8 X 1-3/4”
BOLT
3/8” LOCK NUT
PULLEY
PULLEY
BRACKET
WEIGHT
STACK
CABLE
ARM
CABLE

3
FIGURE 2
• Remove one 3/8” LOCK NUT and one 3/8 X 3-3/4” BOLT from the TOP and BOTTOM PLATES as shown in FIGURE 2.
Discard the 3/8 X 3-3/4” BOLTS.
STEP 2:
3/8 X 3-3/4”
BOLT
3/8” LOCK NUT
3/8 X 3-3/4”
BOLT
3/8” LOCK NUT
0123456
1/2 1/2 1/2 1/2 1/2 1/2

4
FIGURE 3
• Assemble the CABLES (2) to the TOP PLATES using one 3/8 X 4-1/4” BOLT (4), two 3/8” SAE WASHERS (3) and one previ-
ously removed 3/8” LOCK NUT as shown in STEP 3.
STEP 3:
3/8” LOCK
NUT
SHORT
CABLE
3/8 X 4-1/4” 4
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3
2
• Disassemble the SHORT CABLE and the turnbuckle on LONG CABLE (2) as shown in FIGURE 3. The SHORT CABLE will be
reassembled later.

• Assemble the SHORT CABLE and the turnbuckle to each CABLE (2) as shown in FIGURE 4.
FIGURE 4
• CAREFULLY slide the GUIDE BRACKET (1) through the CABLES (2) as shown in FIGURE 4.
STEP 4:
1
2
SHORTCABLE
0123456
1/2 1/2 1/2 1/2 1/2 1/2
5

6
FIGURE 5
• Slide the GUIDE BRACKET (1) up and reattach the WEIGHT STACK CABLE as shown in FIGURE 5.
STEP 5:
WEIGHT
STACK
CABLE
3/8 X 1-3/4”
BOLT
3/8” LOCK NUT
PULLEY
ARM
CABLE
2
• Loop the ARM CABLE around the previously removed pulley and assemble it to the GUIDE BRACKET (1) with the previously
removed hardware as shown in FIGURE 5.

FIGURE 6
• Assemble the CABLES (2) to the BOTTOM PLATES using one 3/8 X 4-1/4” BOLT (4), two 3/8” SAE WASHERS (3) and one
previously removed 3/8” LOCK NUT as shown in STEP 6.
STEP 6:
3/8” LOCK
NUT
3/8 X 4-1/4” 4 3
2
7

8
FIGURE 7
STEP 7:
• Adjust the turnbuckle on each CABLE (2) to add tension to the CABLES (2). Secure turnbuckle with the JAM NUTS as shown in
FIGURE 7.
• Refer to the 777 USER GUIDE to adjust tension in the systems cables and tighten all jam nuts securely.
TURN-
BUCKLE
JAM NUT
2