ParaBody Serious Steel 360101 375 User manual

Serious Steel
1360101 375 LEG PRESS ADAPTERKITi
ASSEMBLY INSTRUCTION
Part# 6837701 1Eevision:07/06/99
All manuals and user guides at all-guides.com
all-guides.com

]IMPORTA~,,T N~)TES
1
There is a risk assumedby individuals whouse this type of equipment. To minirrrize risk, please
follow these rules:
1. Consult your physician before beginning any exercise program.
2. Inspect equipmentdaily. Tio~hten all loose connections and replace wornparts immediately.
Failure to do so mayresult in serious injury.
3. Donot allow minors or children to play on or around this equipment.
4. Exercise with care to avoid injury.
5. If un~fire of proper use of equipment,call your local Parabodydistributor or call the "
Parabody customer service departmentat [phone].
Please note:
* Thankyou for purchasing the Parabody 360101Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product faust be assembled
ona flat, level surface to assure its properfunction.
*Werecommendcleaning your product (pads and frame) on a regular basis, using warmsoapy
water. Touch-uppaint can be purchased from your Parabody customer service representative
at [phone].
! TooI’s Required for Assembly]
* Rubber mallet or hammer
* 3/4" wrench
* 9/16" wrench
* Ratchet with 3/4" and 9/16" sockets
* Adjustable wrench
* Tape measure
Bolt LengthRuler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH RULER:
BOLT LENGTH
All manuals and user guides at all-guides.com

" ~
5
6
7
8
PART# DESCRIPTION
6838003 FRON~FLEG
6693902 Pig I .FY BRACKET
6838103 ’ BASE CONNECTION
3116i01 3-V2"eULLZY
6405201 2" SQ. ENDCAP
6-~700~ 2"SQ.COVERCAP
68~2701’ 2"SQ.r~UBB~BUM~ZR
3102501 3/8" %VASHER
PARTS LIST
QIY KEY PART#
1 9 3102802
1 i0 3102933
212’ 3102937
1 ~ 6837801
2 14 6837901
1 15 ’3’102502
6 16 3102801
DESCRIPTION
3/8" LOCKNUT
3/8 X2" BOLT
1/2X3"BOLT’ ’ ’
lnx
PRLMARYCABLE
LEGPRESSCABLE
I/2" WASHER
.... I~2" LOCK~
NOTE:The LEGPRESSATTACHMENT(832101) must be assembled before connecting it to the
PARABODY375 ttOME GYI~I
STEP 1
¯ Slidetwo2" SQ. COVERCAPS(6) over the FRONTLEG
(I) as sho~vnin FIGURE
FIGURE1
FIGURE2
STEP 3
¯ Attachone 2" SQ, RUBBERBUMPER(7) tothe top ofthePULLEY
BRACKET(2) as shownin FIGURE
STEP 2
¯Slide one 2" SQ. ENDCAF(5) into the BASECONNEC ~
shownin FIGURE2.
3FIGURE3
All manuals and user guides at all-guides.com

STACK GUARD
FIGURE 4
BASE
~ 1/2 WASHER
1/2 X 4" BOLT
STEP 4
¯Removetwo 1/2 X4" BOLTS,two 1/2" WASHERS,and two 1/2" LOCKNUTSfrom the BASEand STACKGUARDas shown in
FIGURE4. (NOTE:Discard the 1/2 X4" BOLT.)
BASE
,STACK GUARD
FIGURE5 I/2X4-1/2"
STEP5
¯Securely fasten the FRONTLEG(I) and the BASECONNECTION(3) to the BASEand STACKGUARDusing two 1/2 X 4-1/2’"
BOLTS(12) and two previously removed 1/2" LOCKNUTS.See FIGURE
[ 1/2 [ 1/2 [1/2 [ 1/2 [ 1/2 [ 1/2
I23 4 5 6
4
All manuals and user guides at all-guides.com

REMOVE
STEP 6
Removethe existing CABLE(part #68331)using the following steps:
¯ Disconnect LATBARfrom TOPBOOM.
¯ Unscrew the threaded end of CABLEfrom the HEADPLATEASSEMBLY.
¯ Route the CABLEaround the FLOAT~’GPULLEYas shown in FIGURE6.
¯ Route the CABLEthrough the TOPBOOMas shown in FIGURE6.
¯ The pulleys in TOPBOOMma.v need to be temporarily removed to remove CABLE.
¯ (NOTE:Discard CABLEpart ~q58331)
FIGURE 6
All manuals and user guides at all-guides.com

FIGURE 7
IMPORTANT: Cable must run
in all the pulley grooves.
;TEP7
Install the NEWPRIMARYCABLE(13) using the following steps:
¯ Route the CABLE(13) through the TOPBOOMas sho~a in FIGURE7. Thepulleys in TOPBOOMmayneed to be temporarily removed
to performthis step. (Note: Makesure the CABLEis running in all the pulley grooves.)
Route the CABLE(13) around the FLOATINGPULLEYBRACKETas shownin FIGURE
Route the CABLE(13) back over one pulley in the GUIDERODSUPPORT,downthrough the PULLEYE;RACKET(2) and over
second pulley in the GUIDERODSUPPORT.
Screw the threaded end of CABLE(13) into the HEADPLATEASSEMBLY.
I 1/2 ~ 1/2 I 1/2 ~ 1/2
6
All manuals and user guides at all-guides.com
all-guides.com

FIGURE 8
STEP8
~3/8 X2"
Loop CABLE(13) around one 3-1/2" PULLEY(4) in the PULLEYBRACKET(2) and SECURELYassemble using one 318 X2"
BOLT(10), and two 3/8" WASHERS(8) and one 3/8" LOCKNLrI"(9) as shownin FIGURE
FIGURE9
STEP9
¯Removeone existing 3-1/2" PULLEY,two WASHERS,
two 2" WHEELSand two SPACERSfrom the
ADJUSTMENTTUBEon the 832 LEGPRESSOPTION
by unfastening the 3/8 X 4-1/2" BOLTholding the
pulley on. See FIGURE9. (NOTE:Thepulley will be
used in STEP12.)
2" WHEEL
3/8 X4-1/2"
BOLT
All manuals and user guides at all-guides.com

WA SPACER
/ DONOT
3/8 X4-1/2" BOLT FIGURE 10
STEP 10
¯ Assemblethe LEGPRESSCABLE(14) to the ADJUSTMENTTUBEon the 832 using the existing previoasly removed3/8 X 4-1/2"’
BOLTS,SPACERS,WASHERS,2" WHEELSANDNUT.(Note: Do not overtighten! Tighten only until nut is completely on bolL)
FIGURE10.
1/2 I 1/2 I1/2 ] 1/2 I1/2 I1/2 1
1 2 [34 5 6
8
All manuals and user guides at all-guides.com

FIGURE 11
STEP11
¯Secure~yfastenthe832LEGPRESSt~theFRONTLEG(~)usingtw~/2X3~BOLTS(~)~tw~/2~WASHE~‘S(~5)~andtw~/2~L~CK
NUTS(16) as shownin FIGURE11.
9
All manuals and user guides at all-guides.com

3/8 X2",
FIGURE 12
STEP12
¯Attach one 3-1/2" PULLEY(4) to the FRONTLEG(1) and one 3-1/2" PULLEY(4) to the BASECONNEC([’ION(3) Using
2" BOLTS(10), four 3/8" WASHERS(8) and two 3/8" LOCKNI_rTS(9). (Note: Makesure CABLE(14) is running
pUI~! ,~YS.)
STEP13
¯Screw the threaded end of LEGPRESSCABLE(14) to the
PULLEYBRACKET(2) as shox~n in FIGURE13.
FIGURE 13
345 6
10
All manuals and user guides at all-guides.com