ParaBody 435104 User manual

435104 LEG PRESS ADAPTER KIT
Part#6865101 Revision:2/15/001
ASSEMBLY INSTRUCTIONS

IMPORTANT NOTES
Please note:
Tools Required forAssembly
* Thank you for purchasing the 435104 Leg Press Adapter Kit. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 7/32” Allen wrench
* Adjustable wrench
* Tape measure
2
NOTE:BOLTLENGTHISMEASUREDFROMTHE UNDERSIDE OFTHEHEADOFTHEBOLT.
BOLT LENGTH RULER:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your Parabody customer service representative
at [phone].
Bolt Length Ruler
0123456
1/2 1/2 1/2 1/2 1/2 1/2
BOLT LENGTH
WELCOMETOTHEWORLDOF Serious steel!
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
2. Do not allow minors or children to play on or around this equipment.
1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
3. Exercise with care to avoid injury.
4. If unsure of proper use of equipment, call your local Parabody distributor or call the
Parabody customer service department at [phone].

STEP 1
FIGURE 1
PART #
6747603
3116202
3108102
6427101
3118701
3201501
6271801
6747901
KEY
1
2
3
4
5
6
7
8
QTY
1
2
1
1
1
1
1
1
PART #
3102701
3102501
3102802
3102502
3102801
3102902
3102910
3102909
DESCRIPTION
3/8”HEXNUT
3/8”WASHER
3/8”LOCKNUT
1/2”WASHER
1/2”LOCKNUT
3/8X2-1/4”BOLT
1/2X3” BOLT
3/8X 1”
QTY
2
3
2
4
4
2
4
1
DESCRIPTION
FRONTLEG
3-1/2”PULLEY
QUICKDISCONNECTLINK
KEYHOLECLEVIS
2”PULLEY
SWIVELSNAP
72”ELASTICCORD
LEGPRESSCABLE
KEY
9
10
11
12
13
14
15
16
NOTE: TheLEGPRESSATTACHTMENT(832101)must beassembledbeforeconnecting ittothe
PARABODY425104HOMEGYM
PARTS LIST
• REMOVEthe four 3/8” X 1”BUTTON HEADCAP SCREWS from the rearSHROUD. Removethe SHROUD fromthe 425104HOME
GYM.SeeFIGURE1.
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
3
3/8” X 1” BUTTON
HEAD CAP SCREW

STEP 2
FIGURE 2
4
REAR
SHROUD
• If the 445104 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed.Apply pressure to the bottom
of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2.
0123456
1/2 1/2 1/2 1/2 1/2 1/2

FIGURE 3
STEP3
• Removetwo 3/8”LOCK NUTS,two 3/8”HEX NUTS,two SWIVEL SNAP(68) (keepelastic cordsattached), two
3/8X 1/2” SPACERS,and one 3/8”THREADED SHAFTfrom thebracket on the BASE as shown inFIGURE 3.
BASE
5
HEXNUT
• Discard the two 3/8 X 1/2” SPACERS.
HEXNUT
3/8 X 1/2”
SPACERS
(DISCARD)
3/8”THREADEDSHAFT
SWIVELSNAP
3/8”LOCKNUT
SWIVELSNAP
3/8”LOCKNUT
ELASTICCORD

6
FIGURE 4
BASE
HEXNUT 3/8” LOCKNUT
2
STEP4
• Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two
previouslyremoved 3/8” LOCK NUTS to the previously removed 3/8”THREADED SHAFT as shown in FIGURE 4.
HEXNUT
3/8”LOCKNUT
0123456
1/2 1/2 1/2 1/2 1/2 1/2
3/8”THREADEDSHAFT
SWIVELSNAP
SWIVELSNAP
FIGURE 5
STEP5
• Removeone 3/8 X2” BOLT, two 3/8”WASHERS,one2-7/8” L-BRACKET, one 4-1/2”PULLEY,and one 3/8”LOCK NUT from the
upper flat on the BASE as shown in FIGURE 5.
BASE
3/8”WASHER
4-1/2” PULLEY
3/8”WASHER
3/8”LOCK NUT
2-7/8”L-BRACKET
3/8”X 2” BOLT

FIGURE 7A
(WITHOUT
445104 SECOND
STACK OPTION)
STEP 7A
3/8”LOCKNUT
TOP BOOM
9 3/8”HEX NUT
• SECURELY assemble one 2” PULLEY(5) to the 3/8”THREADED SHAFT on theTOPBOOMusing one previously installed 3/8”
WASHER, one 3/8”HEXNUT (9) and one previously installed 3/8” LOCKNUTasshown in FIGURE 7A.
5
3/8” WASHER
FIGURE 6
STEP6
• SECURELY assemblethe previouslyremoved 4-1/2”PULLEYtothe BASEusing one3/8 X2-1/4” BOLT(14), two previously
removed3/8”WASHERS,onepreviously removed2-7/8” L-BRACKET,one SWIVELSNAP(6), one3/8” HEXNUT(9), andone
previouslyremoved3/8” LOCK NUT.See FIGURE 6.
BASE
14 3/8X 2-1/4”
3/8”WASHER
4-1/2” PULLEY
2-7/8”L-BRACKET
6
9 HEXNUT
3/8”LOCK NUT
• Ifthe 445104 SECOND STACKOPTIONis installed followSTEP7B .
3/8”WASHER
• Remove one 3/8” WASHER and one 3/8” LOCK NUT from the 3/8”THREADED SHAFT on theTOPBOOM.
7

FIGURE 7B (WITH
445104 SECOND
STACK OPTION)
STEP 7B
• If the 445104 SECONDSTACK OPTION is NOTinstalled proceedto STEP8 .
TOPBOOM
3/8” X 1” 16
10
5 11 3/8”LOCK NUT
• SECURELYassemble one 3/8 X1” BOLT(16),one 3/8”WASHER(10), one2” PULLEY(5)andone 3/8” LOCK NUT(11)to the
bracket on the TOP BOOM as shown in FIGURE 7B.
STEP8
• SECURELY attach one 3-1/2” PULLEY (2) to the FRONT
LEG(1)usingone3/8X 2-1/4” BOLT(14),two3/8”WASH-
ERS(10),andone3/8”LOCKNUT(11). See FIGURE 8.
• Attach the open end of PRESS LINK CABLE (8) to the
QUICKDISCONNECTLINK(3).SeeFIGURE8.
• SECURELY tightentheQUICKDISCONNECT(3)tothe
tabon theFRONT LEG (1) as shownin FIGURE8.
FIGURE 8
2
3/8X 2-1/4” 14
SECURELY
TIGHTEN!
8
10
10 11
1
3
8
0123456
1/2 1/2 1/2 1/2 1/2 1/2

9
STEP9
FIGURE 9
• RouteLEGPRESSCABLE(8)around the 3-1/2” PULLEYontheLEGPRESSand UNDER the3-1/2”PULLEYon the FRONT LEG (1)
asshown in FIGURE 9.
• SECURELYattach the LEG PRESSto the FRONTLEG(1) using two 1/2” X3” BOLTS (15), two1/2”WASHERS(12),and two 1/2”
LOCKNUTS(13).SeeFIGURE9.
LEGPRESS
1/2X 3”15
13
12 8
1

10
FIGURE 10
STEP10
• SECURELYattach the FRONTLEG(1)to425BASEusingtwo1/2X3”BOLTS (15), two 1/2”WASHERS(12)andtwo1/2”LOCKNUTS
(13).SeeFIGURE10.
• RouteLEG PRESS CABLE(8) under the3-1/2”PULLEY on the425 BASE asshown in FIGURE10.
8
13 12
1
1/2 X 3” 15
BASE
0123456
1/2 1/2 1/2 1/2 1/2 1/2