
6
HALL EFFECT SWITCH OPTION
LOW VOLTAGE DC SWITCH (10-30 VDC)
WiringDiagram and Information
HIGH VOLTAGE SWITCH (20-230 VAC/DC)
WiringDiagram and Information
AC
White (3)
Black (2)
Internally Short
Circuit Protected Brad Harrison 40909 Connector
1. Green
2. Black
3. White
SW L1
L2 Pin Receptacle
DC
Color Code
SW
Source
(PNP)
Sink
(NPN)
(+)
(-)
3
Pin Receptacle
AC
Color Code
2
1
2
3
4
5
1. White: +10 to 30 VDC
2. Red: Source
3. Ground Not Connected
Nor Requied (Green)
4. Orange: Sink
5. Black: Common
Brad Harrison 41310 Connector
1
White (1)
Orange (4)
Black (5)
Red (2)
NOTES:
1. Availablewithorwithoutcushions.
2. Notavailablewith stroke adjusters.
3. Pressure rating: 1500 psi
4. Operatingtemperature: -4°F to158°F
5. Specifyswitchtype,orientation andvoltagewhenordering.
6. Not available on PTR/LTR 10 size units.
7. The low voltage DC switch is available in non-rotatable style
only;consultrepresentativeforfurtherinformation.
Theinductive type proximity switch provides end ofrotationindication.
Thenon-contact probe senses the presence of theferrous cushion
spear and has no springs, plungers, cams or dynamic seals that can
wear out or go out of adjustment. The switch is solid state and meets
NEMA 1, 12 & 13 specifications. For ease of wiring the connector
housing is rotatable through 360°. To rotate, lift the cover latch,
position,andrelease.*
The standard proximity switch controls 20-230 VAC/DC loads from 5 to
500 mA. The low 1.7 mA off-state leakage current can allow use for
direct PLC input. The standard short circuit protection (SCP) protects
the switch from a short in the load or line upon sensing such a condition
(5 amp or greater current) by assuming a non-conductive mode. The
fault condition must be corrected and the power removed to reset the
switchpreventingautomaticrestarts.
The low voltage DC switch is also available for use with 10-30 VDC.
This switch is in a non-rotatable housing, but does incorporate the short
circuitprotection.
Both switches are equipped with two LEDs, "Ready" and "Target". The
"Ready" LED is lit when power is applied and the cushion spear is not
present. The "Target" LED will light and the "Ready" LED will go out
when the switch is closed, indicating the presence of the cushion spear.
BothLEDsflashing indicates a short circuit condition.
PROXIMITY SWITCHES
(RED)
SWITCH
_
+
LOAD
*WhenconnectingInductive
Load(relay,electromagnetic
valve etc.) it is recommended
toinsert protection circuit.
Diode100V1A.(NPN
connectionshown)
NOTE: Quantitiesshown are as required per end cap option specified.
ITEM
NO. DESCRIPTION QTY.
55 REEDSWITCH KIT
(Lead Type orQuick Connect) 1
56 MAGNET 2
57 HALLEFFECT SWITCH KIT
(Lead Type orQuick Connect) 1
58 PROXIMITY SWITCH 1
59 O-RING, ADAPTOR BLOCK 1
60 SCREW,SPACER BLOCK 4
61 SPACERBLOCK 1
62 O-RING,SPACER BLOCK 1
63 END CAP 1
64 ADAPTOR BLOCK 1
65 SCREW,ADAPTORBLOCK 2
57 56
64
65 58
59
60
63
62
61
SPECIFICATIONS
Type: Solid State Type (PNP or NPN)
SwitchingLogic: NormallyOpen
SupplyVoltageRange: 5 - 30VDC
CurrentOutputRange: Up to100 mA at 5 VDC,
Up to 200 mA at 12 VDC and 24 VDC
CurrentConsumption: 7 mA at 5 VDC, 15 mA at 12 VDC,
and 30 mA at 24 VDC
SwitchingResponse: 1000HzMaximum
ResidualVoltage: 1.5VMaximum
LeakageCurrent: 10uAMaximum
BreakdownVoltage: 1.8kVACrms for 1 sec., lead to case
Min.Current for LED: 1mA
OperatingTemperature: 14° to 140° F (-10° to 60° C)
LeadWireLength: 39inches(1meter)
BROWN**
(BLACK)
(WHITE)
BLACK**
BLUE**
SWITCH LOAD
SWITCH LOAD
BROWN**
(RED)
(WHITE)
BLACK**
BLUE**
(BLACK)
BROWN**
(RED)
BLACK**
(WHITE)
(BLACK)
+
_
NPN WIRING CONNECTION
PNP WIRING CONNECTION
+
BLUE**
**Applies to SwitchesManufactured
After10/15/93.
_
DC 5 - 30V
DC 5 - 30V
Quick Connect
Option
1Brown
3Blue
4 Black