PARKIT360 TRANSFORMER 15K User manual

READ CAREFULLY
BEFORE OPERATION
IMPROPER USE OF THIS DOLLY CAN
CAUSE DAMAGE TO YOUR TRAILER,
PERSONAL INJURY OR EVEN DEATH. DANGERDANGER
INSTRUCTION MANUAL
VERSION 4.1
TRANSFORMER 15K

IN THE BOX
TRANSFORMER PACKAGES INCLUDE:
Transformer Dolly
Handle Shaft with Controller Mount
Two 12V U1 Batteries
Wireless Controller & USB C Cable
Charger Cable
FIFTH WHEEL ADAPTER
PACKAGE INCLUDES:
Kingpin Adapter
U Locking Pin with D-Clip
QUESTIONS? 1-888-926-5517 x1
WIRELESSWIRELESS
CONTROLLERCONTROLLER
1

UNIVERSAL STABILIZER BARS
2 Landing Leg Tubes (1.5” x 1.5” x 43.5“)
2 Wing Nuts
(3/8”)
4 Lock Washers
(1/2”)
2 Flat Washers
(1/2”)
2 Coupling Nuts
(1/2” x 1 3/4“)
2 Large Bolts
(1/2“ x 2 1/2”)
2 Medium Bolts
(1/2” x 2”)
2 Small Bolts
(1/2” x 1 1/2”)
2 Inner Pivot Tubes
(1.25” x 1.25“ x 3.5”)
2 Outer Pivot Tubes
2 Landing Leg Bolts
(3/8”x 2.5”)
2 Landing Leg
Attachments
(Adjustable)
Mounting Ring Tube
with Through Bolt and Nut
(1/2” x 5“)
2 Inner Tubes (1.25” x 1.25“ x 32”)
2 Outer Tubes (1.5” x 1.5“ x 32”)
6 D-Pins
(3/8”)
THIS ALL-IN-ONE KIT INCLUDES:
SETUP & INSTALLATION
CHOOSE PREFERRED
CONNECTION POINT
CHOOSE YOUR PREFERRED CONNECTION POINT ON YOUR TRAILER:
KINGPIN BOX
PAGE 13-14
LANDING LEG
PAGE 15-16
(1.50" x 1.50" x 3.5")
2

12V U1 DEEP CYCLE
Both batteries arrive pre-connected
and ready to operate.
Battery Voltage is displayed on the
Volt Meter on the Dolly’s Module.
While in storage, charge every
2 months to preserve battery life.
Covered by an Interstate®1 Year
Warranty. (Page 14)
BATTERIES
ASSEMBLY
HANDLE
Insert the Handle into the Dolly.
Secure with D-Clip.
POWER ON/OFF
TURN ON
Pull OUT on the Battery Disconnect.
Press and hold the Power Button until
the light illuminates.
TURN OFF
Press and hold the Power Button until
the light turns off.
Push the battery disconnect IN to
prevent battery drain during storage.
PULL OUT
Enables Battery Power.
PRESS & HOLD
To turn ON or OFF.
PUSH IN
Disconnects Batteries.
3

FEATURES
RECEIVER TUBE
Connect to the Trailer with either the
Kingpin or Gooseneck Adapter.
INTERNAL BATTERY CHARGER
Charges both on-board 12V U1
Batteries. Digital display shows
charging voltage and amperage.
(Page 7)
FREEWHEEL KNOBS
The Transformer wheels are
powered independently by
two 1.7 hp motors.
Engage both motors to move the
Dolly with power, or push by hand
in Freewheel mode.
(Page 8)
INTELLIGENT SPEED CONTROL
Use the Wireless Controller to switch
between High and Low speed for fast
or more precise parking.
Motors Start and Stop gradually for
a smoother parking experience.
(Page 6)
WIRELESS CONTROLLER
Control the Dolly from a distance
and switch speeds on the go!
Charge when not in use.
(Page 6)
SMART BRAKE
7-Way Power Plug that
Controls the Trailer’s
Electric or Surge Brakes.
(Page 5)
4

MODULE FEATURES
POWER ON/OFF
Press and Hold for 2 seconds
to turn ON or OFF.
WIRELESS RECEIVER
Connects controller to the Transformer.
VOLT METER
Allows you to monitor the
Battery Voltage during operation.
Fully charged batteries rest
between 12.6 to 13V.
BATTERY DISCONNECT
Push the big red button to cut off the
Dolly’s electrical connection. Used to
prevent battery drain while in storage
and as an emergency stop.
CIRCUIT BREAKERS
Provides overcurrent protection for the
Motors, Brakes and Control System.
If a breaker trips, the Reset Button will
extend up to 1/2” from the panel.
Allow 15 seconds for the system to
cool down, then press Reset.
SMART BRAKE
7-Way Power Plug that
Controls the Trailer’s Brakes:
Electric Brakes (RV Trailers):
Releases Trailer brakes when Dolly
motors are operating. Engages brakes
when the Dolly is powered ON and not
in motion.
Surge Brakes (Boat Trailers):
Locks out the Surge Brakes when
the Dolly is operating.
5

WIRELESS
CONTROLLER
Operating from the User’s perspective:
Behind the Dolly, facing the Trailer. FORWARD
(BACK UP TRAILER)
REVERSE
(TOWARDS USER)
LEFT WHEEL LOW SPEED
CONTROLLER ON
RIGHT WHEEL
HIGH SPEED
ON
In Use
Battery Low
Sleep Mode
LED INDICATOR LIGHT
Off - Enters this mode after
60 seconds of inactivity
Slow Blink - During Button Press
Steady - Press LOW to Activate
Fast Blink - Charge ASAP!
CHARGING THE CONTROLLER
The included braided USB C cable is
compatible with any charger block.
Once plugged in, two internal LED lights
will indicate the battery charge level: CHARGING BATTERY FULL
FORWARD REVERSE COUNTER-CLOCKWISE
CLOCKWISE
RESET PORT
6

12V BATTERY CHARGING
CHARGER DISPLAY
Shows Charge Level of Battery when
connected to a 120V power outlet.
While charging, the display alternates between
Charging Amperage and Voltage. The battery
graphic shows the % complete.
When charging is complete, FUL is displayed
and the battery graphic is completely lled:
Get an Error Code? (ERR) Check the terminal
connections and Dolly plug to ensure they are
properly connected.
Get a Repair Code? You may have a faulty
battery. Please call us to order a replacement!
PULL OUT
Ensures Batteries are connected.
Monitor charger display
above charger plug.
POWER OFF
Press and hold for
2 seconds to turn the
Transformer Dolly OFF.
PLUG IN
Plug the Charger Cable
into the Dolly, then into
the nearest wall outlet.
PREPARING THE DOLLY
CHARGING VOLTAGE
CHARGING AMPERAGE
BATTERY FULLY CHARGED
7

FREEWHEEL/SPOOL
NEUTRAL. MOVE THE DOLLY WITHOUT
POWER WHILE IT IS NOT UNDER LOAD.
Turn both of the Transformer’s motor knobs in the
direction of the Freespool arrow until it stops. Freely
move the Dolly to and from the trailer in this mode.
DRIVE
ENGAGE THE MOTORS TO CONNECT TO
THE TRAILER AND PARK WITH POWER.
Ensure the Dolly is in parking position underneath the
trailer hitch.
Turn both of the Transformer’s motor knobs in the
direction of the Engaged arrow until it stops and clicks
into position. Rock the Dolly back and forth to ensure
the motor is engaged.
Use the wireless controller to move the Dolly.
When pushed manually in this mode, the Dolly will only
move an inch forwards or backwards before stopping.
FREEWHEEL KNOBS:
SWITCHING GEAR
8

DANGER
DO NOT EXCEED DOLLY’S
MAX. WEIGHT CAPACITY
CAN CAUSE DAMAGE TO YOUR TRAILER,
SERIOUS INJURY, OR EVEN DEATH.
INSTALL UNIVERSAL
STABILIZER BARS
BEFORE MOVING TRAILER
CHOOSE A COMPATIBLE TRAILER CONNECTION POINT ON
THE TRAILER’S KINGPIN BOX, OR LANDING LEGS.
DO NOT OPERATE ON
MORE THAN 4% GRADE
RISK OF RUNAWAY TRAILER.
DO NOT OPERATE ON STEEP INCLINES.
FIFTH WHEEL / KINGPIN
UP TO 15,000 LBS GROSS
(3,000 LBS TONGUE)
GOOSENECK
UP TO 12,000 LBS GROSS
(1,500 LBS TONGUE)
9

CONNECTING TO YOUR TRAILER:
FIFTH WHEEL ADAPTER
With both motors in Freewheel Mode, move the
Dolly, Accessories and required Tools to the Trailer:
Kingpin Adapter, Stabilizer Bar Kit and Hardware,
3/4" Socket, Wrench and Impact Drill with 25/64” bit.
INSTALLATION
Attach the Kingpin Adapter to
the trailers’ Kingpin and slide the
U-shaped locking pin into place.
Secure this connection with the
supplied D-Pin.
KINGPIN ADAPTER
INSTALL UNIVERSAL STABILIZER BARS
BEFORE MOVING TRAILER! (SEE PAGE 13-16)
10

MOUNTING RING TUBE
PRE-ASSEMBLY
Install the Pivot Tubes based on your prefered Stabilizer Bar Connection:
KINGPIN ADAPTER
MEASUREMENTS
Kingpin measurements should be between 48” to 52”
from the Ground to the Bottom of the Kingpin Box.
If your measurements are not within this range,
contact us before operating this machine!
48”-52” h
161/2” h
FLUSH
STRAIGHT
LEVEL
KINGPIN BOXKINGPIN BOX (Pg 13)
MOUNTING HOLES UP
PIVOT TUBES ON SIDES
LANDING LEGLANDING LEG (Pg 15)
MOUNTING HOLES DOWN
PIVOT TUBES BELOW
INSTALLATION
Slide the assembled Mouting Ring Tube
over the base of the Kingpin Adapter.
Secure with the 5" Through Bolt and Nut.
11

ENGAGE MOTORS INTO DRIVE
TURN ON THE DOLLY
Press and Hold the Power Button
to turn on the Dolly. Connect the
Trailer’s 7 Pin Brake Cable to the
Smart Brake Plug.
FREEWHEEL KNOBS
Ensure the Dolly is in parking
position and ready to connect to
the Hitch, then Engage both Motors.
(See page 8)
LEFT
INSERT ADAPTER
RIGHT
With the Wing Tube pre-assembled and installed:
Turn on the Wireless Controller. Drive the Dolly underneath the
hitch and align the Receiver Tube with the Kingpin Adapter.
Ensure that the trailer is level and the adapter is straight.
Use the trailer's jack to fully lower the trailer into the Dolly.
12

KINGPIN BOX
STABILIZER BARS
OUTER PIVOT TUBES
Install both 1 1/2” Outer Pivot Tubes to
the wings of the Mounting Ring Tube.
Thread 2 1/2" x 1/2” bolt and lock washer
into end of each wing.
Turn the pivot tubes towards your trailer in
preparation for the Outer and Inner tubes.
KINGPIN BOX
Thread the 1 1/2” bolt through the
Kingpin Box and into the Coupling Nut.
You may have to remove one of the existing
bolts from your Kingpin Box.
Tighten the Coupling Nut as much as
possible for a secure connection.
INNER PIVOT TUBES
Attach both Inner Pivot Tubes to each
Coupling Nut with supplied 2" x 1/2" bolt
and lock washer. Angle this in the direction
of the Pivot Tubes.
Repeat these steps on the other side
of the Kingpin Box.
INSTALLATION VIDEO
YOUTUBE.COM/PARKIT360
13

KINGPIN BOX STABILIZER BARS
OUTER & INNER TUBES
Slide the Inner Tubes into the Outer Pivot
Tubes at the base of the Kingpin Adapter.
Slide the Outer Tubes onto the Inner
Trailer Mount Pivot Tubes on the
Kingpin Box and secure them with
the supplied D-Pins.
TIGHTEN BOLTS
Tighten all 4 Bolts on the top and bottom
pivot tubes to complete the setup.
CONNECT TO TRANSFORMER
If you have not done so already:
Lower the Kingpin Adapter into the Dolly's
Receiver Tube.See Page 12 for details.
DRILL PILOT HOLES
Using the pre-made holes in the Outer Tube
as a guide, drill a hole into one side of the
Inner Tube, and then the other to complete
the through hole. Secure these with D-Pins.
We recommend a 25/64” drill bit.
USE THE WIRELESS CONTROLLER
TO PARK THE TRANSFORMER.
READY TO MOVE!
14

LANDING LEG
STABILIZER BARS
INSTALLATION VIDEO
YOUTUBE.COM/PARKIT360
INNER PIVOT TUBES
Install both 1 1/4” Inner Pivot Tubes to the
bottom of the Mounting Ring Tube with a
2 1/2” bolt, lock washer, and at washer.
MOUNTING RING TUBE
Slide onto the Kingpin Adapter with pivot
tubes down. Use the 5” through bolt and
nut to secure through the lower hole.
CONNECT TO TRANSFORMER
Lower the Kingpin Adapter into the Dolly's
Receiver Tube.See Page 12 for details.
LANDING LEG TUBES
1. Connect the Outer Tubes to both Inner Pivot Tubes with D-Pins.
2. Slide the Long Outer Tubes over the Inner Tubes, then point them towards the trailer.
3. Twist both Landing Leg Attachments into the end of each Long Outer Tube.
INNER TUBES
OUTER TUBES 1
32
LONG OUTER TUBES
15

CONNECT TO TRAILER LEGS
For safety while parking, retract the Trailer's Landing
Legs until the feet are at least 2" off of the ground.
Choose a connection point on the trailer's Landing
Legs that allows the Stabilizer Bars to sit as close
to level as possible.
Attach the bars to the outside of each leg with the
supplied 3/8” Bolts and Wing Nuts.
USE THE WIRELESS CONTROLLER
TO PARK THE TRANSFORMER.
READY TO MOVE!
LANDING LEG STABILIZER BARS
DRILL HOLE
Drill a hole where the Long Outer Tubes and
Inner Tubes meet. Attach with D-Pins.
TIGHTEN BOLTS
Once the Stabilizer Bars are fully installed,
tighten the Bolts on the Inner Pivot Tubes to
prevent further movement.
LONG OUTER TUBES
INNER TUBES
16

PARKING YOUR TRAILER
Use the Forward and Reverse buttons on the Wireless Controller
to steer into tight spaces that are nearly impossible for vehicles.
DISCONNECTING THE HITCH
Chock Trailer Wheels to prevent a runaway trailer. Raise the Trailer
to withdraw the Adapter. The Adapter can be removed or left on the
hitch for later use.
QUESTIONS?
STORAGE & MAINTENANCE
Grease Axle Fittings: Using a grease gun, apply all-purpose grease
to the ttings on the outside of each wheel. Remove the chain cover
and apply grease to the ange bearing ttings on the axel.
Charging the On-Board Batteries: Pull out on the Battery Disconnect
to connect the batteries. Plug the Charger Cable into the Dolly and
the opposite end into a nearby wall outlet. (Page 7)
Grease the Receiver Tube and Lubricate the Chain with Chain Lube.
Freewheel the Dolly to desired storage area, preferably under cover.
CALL TOLL-FREE:
1-888-926-5517 ext.1
17

TRAILER JACK POST
Lower the Trailer Jack into the
Dolly’s Receiver Tube, following
the standard connection process.
The trailer should rest as close
to the Dolly’s Tires as possible to
reduce strain on the Jack Shaft.
TELESCOPIC FRAME ADAPTER
Attach the Telescopic Adapter to
the Y section of the trailer frame.
Lower the Telescoping Pipe into
the Dolly. Slide the Adapter’s
locking pin into place.
ALTERNATE CONNECTIONS
CALL TOLL-FREE:
1-888-926-5517
Ext. 1 - Sales & Service
PARKIT360 OFFICE HOURS
8AM-4PM EST (WEEKDAYS)
[email protected]
suppor[email protected]
JACK POST
ADAPTER VIDEO
YOUTUBE.COM/PARKIT360
TELESCOPIC
ADAPTER VIDEO
YOUTUBE.COM/PARKIT360
18

2 YEAR PARTS & REPAIR WARRANTY
Your Parkit360 Dolly is covered for 2 years from the initial date of purchase.
If a defect is found during this time, contact us with the original sales receipt
number and details of the fault encountered. Our Technical Support will attempt
to solve the issue remotely. If the issue appears to be caused by defective parts,
we will provide free replacement parts, excluding shipping costs.
If the 2 Year Warranty has expired or if you are not the original owner, you
will have to pay the cost of parts and shipping. This repair will be covered for
3 months, starting 7 days from the date of shipment.
The Repair Warranty will expire either at the end of the 3 month period, or at
the expiration of the original 2 -Year Warranty, whichever is later.
30 DAY RETURN POLICY
If a material defect is found or if the Parkit360 has failed to perform to your
expectations, return it within 30 days of the date of sale for a refund, less the
at shipping cost of $500 USD and $200 restocking fee.
1. Pack the Dolly back into the box and onto the skid that it came in.
Call us at 1-888-926-5517 EXT.1 to let us know about your return.
Please provide us with your Sales Receipt or Online Order number.
2. Our staff will provide you with an RMA# that must be written on the box
prior to sending. We will email you a Return Shipping Label that must be
axed to the box prior to drop off at your nearest FedEx Depot.
(If you are unable to drop off the Unit, Pick-Up can be arranged.)
3. Receive your refund minus the shipping and restocking fee once the Dolly
arrives at our warehouse.
EXCLUSIONS AND LIMITATIONS
The 2 Year Warranty and 30 Day Return Policy do not cover:
• Normal wear and tear of the Parkit360 from use
• Shipping Costs for Returns / Repairs
• Customer Neglect and Improper Use or Storage of the Parkit360
• Modied Dollies, or if the Serial Number has been altered or removed
• 12V U1 Batteries are covered separately by an Interstate® 1 Year Warranty.
Find a Service Location near you: interstatebatteries.com/location-nder
19