Patriot Lighting MH189 User manual

210619
SKU Number: 351-8771
1-LIGHT WALL LIGHT
Model Number: MH189
PACKAGE CONTENTS
HARDWARE CONTENTS
Mounting Plate Unit
X1
Mounting Screw
X2
Wire Connector
X3
Bolt Nut
X2
AA
CC
BB
DD
C
B
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
Note: Hardware not shown actual size.
A
Fixture Screw
X3
EE

Page 2 of 4
210619
Turn off the power at the fuse or circuit box.
1. Attach the mounting
plate unit(AA) to the
outlet box using two
mounting screws
(BB).
Please read and understand this entire manual before attempting to assemble, operate or install the product.
WARNING
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
●All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
●Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
PREPARATION
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Slotted Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire
Cutters, Safety Glasses, Ladder, Wire Stripper.
ASSEMBLY INSTRUCTIONS
SAFETY INFORMATION
1
Outlet Box
AA
BB
2
CC
2. Pull out the source
wires from the outlet
box, make wire
connection using
Green Ground
Screw
Fixture
Mounting Screw
wire connectors(CC)
as follows:
---Connect the black
(hot) wire from the
fixture to the black
(hot) wire from the
power source.
---Connect the white
(neutral) wire from the fixture to the white(neutral) wire
from the power source.
---Attach the fixture ground wire(bare wire) to the
mounting plate unit(AA) with the green ground screw,
then connect fixture ground wire to the house ground
wire with a wire connector(CC).
Carefully put the wires back into the outlet box.

Page 3 of 4
210619
ASSEMBLY INSTRUCTIONS (continued)
4. Attach the metal
ring(B) and glass
shade(C) to the
glass holder, then
align holes of glass
Glass Holder
Fixture Mounting
Screw
shade(C) and metal
ring(B) to the glass
holder, then secure
them with fixture
screws(EE).
5
34
3. Attach the backplate
(A) of fixture to the
mounting plate unit
(AA) by aligning and
inserting two fixture
mounting screws into
the holes on the
backplate(A), then
secure the backplate
(A) with two bolt nuts
(DD).
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
Turn on the power at the
fuse or circuit box.
5. Install 1x60W medium
base bulb(Type T or ST,
not included).
See relamping label at
socket area or packaging
for maximum allowed
wattage.
Medium Base Bulb
Max. 60W
(not included)
B
C
EE
DD
AA
A
Spare Parts List:
Assembly Kit
6416MM(1 SET)
Glass Shade
10269SC
C
Mounting Plate Unit
X1
Mounting Screw
X2
Wire Connector
X3
Bolt Nut
X2
AA
CC
BB
DD
Fixture Screw
6426FS
EE

Page 4 of 4
210619
●To clean, turn off and wipe with a damp, non-abrasive cloth.
1) The light does not work:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when light is turned on.
Check for crossed wires, ensure wiring is correct.
If unable to fix any of the above issues, please consult a certified electrician.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor,injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R