PC Locs 16 SCB User manual

www.pclocs.com.au
16 SCB Sync Station
USER INSTRUCTIONS

Contents
Overview ....................................................................................................................................... 1
Specifications.............................................................................................................................. 1
Compliance and approvals ........................................................................................................ 2
Safety instructions...................................................................................................................... 2
Set up........................................................................................................................................... 3
How to charge multiple devices ............................................................................................... 3
How to sync multiple devices ................................................................................................... 4
Troubleshooting........................................................................................................................... 5
PC Locs and the Padlock device are Trademarks of PC Locs Pty Ltd. Copyright PC Locs Pty Ltd Oct 2011.
iPad and iTunes are trademarks of Apple Inc. Windows is a registered trademark of Microsoft Corporation.
Disclaimer
This information is the intellectual property of PC Locs Pty. Ltd. and may not be distributed, duplicated
or copied in part or full without the written permission. Since the use of this information, the equipment
connected and the conditions by which any PC Locs product is used is beyond the control of PC Locs,
it is the obligation of the owner and/or user to determine the correct and safe use of any equipment and
product. To the extent that the law permits, any liability which may be incurred as a result of the use
or future use of a product manufactured or sold by PC Locs Pty. Ltd. is limited to the cost of repairing
or replacing the failed product or component at the discretion of PC Locs Pty. Ltd. either within, or
outside of warranty periods, and does not extend to any loss or damage which may be caused as a
consequence of misuse or failure of the equipment or product or the information contained herein. PC
Locs Pty. Ltd. shall not in any event be liable for economic loss of profits, indirect, special, bodily injuries
or consequential damages.

www.pclocs.com.au
16 SCB Sync Station
USER INSTRUCTIONS
1
Model Number: 16 SCB Sync Station
Part Number: ELE7000
Dimensions: 250 x 216 x 66mm
Weight: 2.5 kg
Operating Temperature: 0 to 70 Degrees Celsius
Input: 250V AC, 50Hz, 1.7A
Output: 5V DC, 2.1A (x16)
USB Standard: USB1.1 and USB2.0
data rates supported
up to 480Mbps
Specifications
iPad Tablet
USB Connectors
(Type-A)
Host Computer
USB Connector
(Type-B)
Carry Handle
Cushioned Feet
(Rear and
Bottom sides)
IEC Connector
Power Inlet
and Fuse
Operating Mode
LED Indicators
Ventilation
Holes
Power Switch
Overview
The PC Locs 16 SCB unit is a compact and portable robust sync and charge station that
provides high current charging and synchronisation capability for up to 16 iPad tablets.
Designed specifically to supply the maximum charge capability of up to 2.1A for the iPad/
iPad2 tablet, this unit is also available for other devices on request.

www.pclocs.com.au
16 SCB Sync Station USER INSTRUCTIONS
2
Safety instructions
For your safety – Do not operate the unit if the plug, power socket, power
cable or enclosure is damaged.
To reduce the risk of fire, electrical shock and/or injury, the following basic precautions
should be followed:
• Thisdeviceisnotintendedforusebypersons(includingchildren)withreducedphysical,
sensory and mental capabilities, or lack of experience and knowledge, unless they have
been given supervision or instructions concerning the use of the device by a person
responsible for their safety.
• CAUTION:ToreducetheRickofElectricShock–useonlyindoors.
• Keepawayfromallsourcesofwaterormoisture.Neverexposethedevicestotherainor
dangerous gas.
• Theunitmaybewarmduringworking.Keepitinadryandcoolplaceanddonotcover.
Ensure sufficient ventilation at all times.
• Donotoverloadthesocket-outlets.
• Before using the product, check and make sure all devices are correctly and
properly connected.
• Arrangethepowercordawayfromtrafcareaswhereitwillnotbetrippedover.
• Theunitispoweredwhenthemainsupplyisconnectedandswitchedon.
• Removethepowercordfromthemainoutletbeforecleaning.Tounplugalwaysgrasp
and pull the plug. Never pull the cord.
• Do not try to repair, disassemble or modify the unit. There are no user-serviceable
parts inside.
• Donotusetheproductotherthanforitsintendeduse.
Compliance and approvals
C-Tick Approval: N26682
Conforms to AS/NZS 60950.1
SAA Approval: SAA111511EA

www.pclocs.com.au
16 SCB Sync Station
USER INSTRUCTIONS
3
Set up
1. If the sync station is in any packaging, remove this to ensure good ventilation and dispose
of responsibly.
2. If the sync station is fitted in the trolley/cart drawer, no relocation is necessary.
3. Ensure the sync station power switch is OFF and the mains power outlet is switched OFF.
4. Insert the power cord into the sync station, and plug the other end into the mains power
outlet. Switch the mains power outlet ON.
How to charge multiple devices
1. Connect all the devices required to be charged to the sync station USB sockets using only
approved USB cables. The devices may be connected to any of the USB sockets, in any
order and any sequence.
2. Switch the sync station power-switch ON. The Charge light and Sync light will illuminate
momentarily, then the Charge light will remain ON.
3. All the devices are now being charged.
4. To check the charge status of any device, momentarily switch the selected device ON and
check its on-screen charge indication.
5. When all the devices are fully charged, switch the sync station OFF.

www.pclocs.com.au
16 SCB Sync Station USER INSTRUCTIONS
4
How to sync multiple devices
1. Connect all the devices required to be synchronised to the sync station USB sockets
using only approved USB cables. The devices may be connected to any of the USB
sockets, in any order and any sequence.
2. Switch the sync station power-switch ON. The Charge light and Sync light will illuminate
momentarily, then the Charge light will remain ON.
3. All the devices are now being charged.
4. Connect the sync station to the host computer which contains the synchronisation
software using an approved Type A to Type B USB cable. In the case of iPad devices the
synchronisation software is iTunes and the host computer should be an Apple computer.
Note iTunes may only synchronise up to 7 devices at a time if used on a Windows PC.
5. Upon connecting the sync station to the host computer, the sync station will automatically
switch from Charge Mode to Sync Mode and this will be signified by the illumination of
the Sync light.
6. iTunes will then seek to identify all the connected devices and they should sequentially
appear in the iTunes window and commence synchronisation simultaneously. The screen
on each device should reflect “Synchronisation in Progress”
7. Upon completed of synchronisation the devices will revert to their standby screen.
8. Removing the USB cable from the host computer will return the sync station into Charge
Mode and the devices will automatically resume charging if needed.
Notes: Before attempting a synchronising of an iPad with iTunes using the sync station, the
iPad should be registered separately first with iTunes following the instructions that came
with the iPad.

www.pclocs.com.au
16 SCB Sync Station
USER INSTRUCTIONS
5
Troubleshooting
1. If no lights are illuminated with the sync station is switched ON, check the power cable is
fully inserted into the sync station socket and the other end is fully inserted into the mains
power socket and the switch is ON.
2. If it has been confirmed power is available, check the fuse in the power socket on the
sync station. First switch off power on the mains socket and remove the power plug.
Remove the power cable from the socket in the sync station and slide out the fuse drawer.
Check the fuse is intact. If not an original spare fuse is retained in the same slide out
drawer. Only replace with an equivalent part: 5x20mm, 4A fast blow.
3. To check the sync station is operating correctly, switch the sync station OFF. Remove all
connected USB cables and switch back ON again. Both the Charge light and the Sync
light should momentarily illuminate. The Charge light will flash a number of times before
remaining on. This is normal operation.
4. If the sync station is operating normally but the devices cannot be charged, check
the USB cables connecting to the devices are of the correct type and quality and not
damaged.
5. If the sync station is operating normally but the devices cannot be synchronised, check
the USB cables connecting to the devices are of the correct type and quality and not
damaged.
6. Any other issues relating to synchronisation problems should be referred to your IT
department or provider of synchronisation software.

WARRANTY
PC Locs warrants the product to be free of defects in design, materials, assembly and
craftsmanship for a period of twelve months from the date of purchase to the original retail
purchaser. Evidence of original purchase will be required to obtain warranty service.
In the event that a defect, malfunction or failure occurs or is discovered during the warranty
period, PC Locs will repair or replace, at its option, the products which in the reasonable
judgment of PC Locs are deemed defective. All transportation costs shall be borne by the
owner and the risk of loss shall be upon the party initiating the transportation.
The warranty does not apply to any product that has been subject to misuse, tampering,
neglect, or accident or as a result of unauthorized alterations or repairs to the product. The
warranty is in lieu of all warranties expressed or implied, including the implied warranties
of merchantability and fitness for a particular purpose which are expressly excluded or
disclaimed. In no event will PC Locs, their directors, officers, employees, or agents be liable
for any harm, consequential, incidental, third party, special or indirect damages whatsoever
arising out of the use or inability to use the products even if PC Locs has been advised of
the possibility of such damages. PC Locs obligation is strictly and exclusively limited to the
replacement or repair of any defective products. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
www.pclocs.com.au
Call 1300 725 627
Distributed by