PC Locs Revolution ECO 16 Bay Trolley User manual

USER INSTRUCTIONS
Revolution ECO 16 Bay Trolley™
Revolution ECO 28 Bay Trelley™
www.pclocs.com.au www.lockncharge.com

Revolution ECO 16 and 28 Bay Trolley
Congratulations on your purchase.
Follow these instructions for easy and fast set-up of your Revolution ECO Trolleys.
PC Locs, LocknCharge and the Padlock device are Trademarks of IWS Global Pty Ltd.
Copyright IWS Global Pty Ltd, May 2014.
Disclaimer.
This informaon is the intellectual property of IWS Global Pty Ltd and may not be distributed, duplicated
or copied in part or full without the wrien permission. Since the use of this informaon, the equipment
connected and the condions by which any IWS Global product is used is beyond the control of IWS Global,
it is the obligaon of the owner and/or user to determine the correct and safe use of any equipment and
product. To the extent that the law permits, any liability which may be incurred as a result of the use or
future use of a product manufactured or sold by IWS Global is limited to the cost of repairing or replacing the
failed product or component at the discreon of IWS Global either within, or outside of warranty periods,
and does not extend to any loss or damage which may be caused as a consequence of misuse or failure of
the equipment or product or the informaon contained herein. IWS Global shall not in any event be liable for
economic loss of prots, indirect, special, bodily injuries or consequenal damages.

INSTRUCTION MANUAL
Fit the ECO power board side
panel (16 bay trolley)
Unpack the trolley
The boxes in the
top of the Trolley
contain the wheels
and fittings.
Attach Castors
On a carpeted surface turn the trolley upside down.
Insert castor wheels into the leg ends and ensure
the threaded hole in the castor wheel post lines up
with the hole in the trolley leg. Screw in the socket
screw with a flat washer and a spring washer using
the Allen Key.
Extra Tools required:
Hammer, Philips head screwdriver, medium adjustable spanner. (Allen key supplied)
(Panel colours for illustration purposes only)
Standard castors PU Wheels (optional) Weather cover (optional)
Slide the panel up and under the top
rail on the side of the trolley that has
the large power board opening.
Using the small bolts and washers
secure the panel from the inside of the
trolley using the Allen Key (2 in the top
of the panel and 2 in the bottom)
Fit the other side panel to the trolley
using the same technique. Lift one
end of the adjustable shelf up off its
support bar and remove the bar.
Carefully let that end of the shelf down.
Repeat the process the other end of the
shelf, so that the shelf unit is in the
bottom of the trolley frame. Fix the last
2 Allen screws to the middle of each
colour side panel from inside the frame.

Revolution ECO 16 and 28 Bay Trolley
Turn the trolley right side up. Using a Philips
head screwdriver remove the shipping screws
from both sides of the adjustable shelf unit.
Fix the adjustable laptop shelf
The fixings kit includes the ‘hammer-in’
security pins and a punch bar.
Find the correct height for the shelf by
sliding one of the laptops you intend to use
into the trolley.
Adjust the shelf height as determined by the size of your laptop. Refit
the shelf support bar to both sides of the trolley frame and ensure the
holes in the bar are facing outwards to line up with the holes in the
edge of the shelf unit. Refit the laptop into the shelf, with the charging
lead plugged in, and check there is sufficient clearance for the laptop
to slide in and out easily. A closer fit means better laptop security.
Unpack the ‘COLOUR PACK’ - trolley lid,
side panels, locking bars, and fixings kit.
Note: for 16 bay only (28 bay panels come
installed)
Insert the 4-way Power Boards
Press the powerboards into the clips
in the tray top. If a powerboard is
loose in its clip, remove power board
then slightly squeeze the clip sides
together and refit the board
Insert the plugs through the hole in
the end of ECO board bracket and out
through coloured side panel square
holes.
Insert the ECO Safe Charge™
power board(s)
Insert the ECO Safe Charge™ power board in the
bracket located on the inside of the top tray. The
plug exits the frame through the adjacent square
hole. The four plugs can then be plugged into the
ECO board.
Use the cable ties to tidy up the leads.

INSTRUCTION MANUAL
Install the bottom tray
Slide tray in from one end. Ensure tray sits flat
Insert the M5 x 25mm Metal Fixing Pins into each of
the fixing holes on the shelf ends. Push them all the
way in until the shoulder of the pin is hard up against
the frame. Now using the supplied punch and your
hammer, punch the pin all the way in. It is designed to
spread out inside the trolley frame to prevent removal.
Repeat the process with all of the fixing holes.
Locking the trolley
The locking bar should be positioned in the shelf about
midway to ensure that the laptops cannot be removed.
Use a marker pen on the frame to indicate which holes
should be used for the locking bar each time. Use the
supplied padlocks to secure the locking bar. Keep the
keys in a secure place.
Installing the lockable lid
On a clean surface place the lockable lid upside
down Disassemble the cam lock as shown
Insert the Cam Lock from the underside with the
lock cam facing in the correct direction.
Now fit the locking nut over the main shaft of the
cam Lock and tighten using your spanner. DO NOT
OVER TIGHTEN as this may distort the lid.
Fix the adjustable laptop shelf
(continued)
Check that the shelf is fitted level in the trolley frame
by counting the same number of locating holes above
the fitted shelf on each leg (there is an extra hole on
the bottom of one side for the lock pin). Check that
the holes in the shelf and the support bars line up by
slightly lifting the shelf off the bar.
Check again that your test laptop fits in the shelf unit
in ALL bays with its charge lead attached.
ONCE THE SHELF IS FIXED IT IS IMPOSSIBLE TO ADJUST THE HEIGHT.

Revolution ECO 16 and 28 Bay Trolley
Install the Security Chain Kit
Tools required:
> Masonry hammer-drill
> 10mm masonry drill bit
> Pencil and ruler/tape
> Hammer
> 13mm and 17mm spanners
Fit the lock tongue as shown
Fit the small washer and M6 nut over the
lock tongue and tighten. DO NOT OVER
TIGHTEN to avoid stripping the thread.
Turn the Lockable Lid right way up. The
keyway should be pointing to the left and
the lock tongue pointing out from the lid.
This is the ‘locked’ position.
Mark the centre of each of the 3 holes.
Drill a 10mm hole through each of the
3 marked centres to a depth of 50mm,
using the floor plate as a guide.
Insert the anchor bolts with nut attached into the
holes through the floor plate. Using the 13 mm
spanner, progressively tighten down each of
these anchor nuts so that all three bolts are
firmly anchored into the concrete.
Now undo each of the three nuts, and in their
place thread on the three silver shear-nuts.
Ensure that the ‘cone’ is down and the hexagonal
nut is up. Using the 17mm spanner tighten
down the three shear nuts until the hexagonal
‘head’ shears off, leaving just the cone ‘base’.
Test the locking mechanism by inserting the key and turning in a clockwise direction. This is the
unlocked position. The lid can now be fitted to the trolley by sliding the non-lock end into the
bracket at the end of the trolley top and lowering the lock end of the lid onto the bracket.
Wheel your PC Locs RR Trolley to the location in which you intend to store and secure it.
Ensure that the trolley (and chain) will reach the intended Floor Plate location.
It is best if the Floor Plate is located as close as possible to a vertical wall to reduce the hazard of
personal injury. Insert the pin end of the chain in the trolley and position the plate end in the desired
position on the floor. NOTE: If mounting on carpet you will need to cut out the carpet from the area
where the floor plate attaches
> The PC Locs ‘RR Security Chain Kit’ containing
the following:
– 1 x 3 holed Anchor Plate and security chain
– 3 x 55mm long, 8mm Anchor Bolts
– 3 x Shear Nuts and washers
– 1 x BSD Lock and key set
Installing the lockable lid
(continued)

INSTRUCTION MANUAL
Slide the security pin through the hole in the Leg of
the RR Trolley and secure the pin using the PC Locs
padlock.
The trolley is now secured and should be secured in
this way at the end of every school day.
Fitting Instructions for Weather Cover
Using the Allen Key loosen the bolts that secure the
coloured cleat. Remove one bolt completely.
Slide the sleeve on the rear of the Weather
Cover bag over the cleat.
Re-secure the cleat using the small bolts.
Unzip the bag and install the Weather Cover
bag over the Trolley Frame.
NOTE: It is recommended the Weather Cover
be rolled up and packed into the bag when
the laptops are being charged in the trolley.
Cleat Bolt (inside trolley) Loosen Bolts
Congratulations!
Your Revolution Range® ECO Laptop Trolley is now ready for use.
For charging purposes read the instructions of how to use the ECO Safe Charge Power board.
Installing the Security Chain Kit
(continued)

www.pclocs.com.au www.lockncharge.com
Warranty
PC Locs/LocknCharge warrants the product to be free of defects in design, materials, assembly and crasmanship
for a period of twelve months from the date of purchase to the original retail purchaser. Evidence of original
purchase will be required to obtain warranty service.
In the event that a defect, malfuncon or failure occurs or is discovered during the warranty period,
PC Locs/LocknCharge will repair or replace, at its opon, the products which in the reasonable judgment of PC
Locs/LocknCharge are deemed defecve. All transportaon costs shall be borne by the owner and the risk of
loss shall be upon the party iniang the transportaon.
The warranty does not apply to any product that has been subject to misuse, tampering, neglect, or accident or as
a result of unauthorized alteraons or repairs to the product. The warranty is in lieu of all warranes expressed or
implied, including the implied warranes of merchantability and tness for a parcular purpose which are expressly
excluded or disclaimed. In no event will PC Locs/LocknCharge, their directors, ocers, employees, or agents be
liable for any harm, consequenal, incidental, third party, special or indirect damages whatsoever arising out of the
use or inability to use the products even if PC Locs/LocknCharge has been advised of the possibility of such damages.
PC Locs/LocknCharge obligaon is strictly and exclusively limited to the replacement or repair of any defecve
products. Some states do not allow the exclusion or limitaon of incidental or consequenal damages, so the
above limitaon or exclusion may not apply to you.
Compliances and Approvals