PC Locs lockncharge iQ 20 Cart User manual

USER INSTRUCTIONS
ENG
TRK
ESP
PRT
FRA
DEU
ITA
www.pclocs.com.au www.lockncharge.com
iQ 20 Cart™

iQ 20 Cart
Congratulaons on your purchase.
Follow these instrucons for easy and fast set-up of your iQ 20 Cart.
PC Locs, LocknCharge and the Padlock device are Trademarks of IWS Global Pty Ltd.
Copyright IWS Global Pty Ltd, May 2014.
Disclaimer.
This informaon is the intellectual property of IWS Global Pty Ltd and may not be distributed, duplicated
or copied in part or full without the wrien permission. Since the use of this informaon, the equipment
connected and the condions by which any IWS Global product is used is beyond the control of IWS Global,
it is the obligaon of the owner and/or user to determine the correct and safe use of any equipment and
product. To the extent that the law permits, any liability which may be incurred as a result of the use or
future use of a product manufactured or sold by IWS Global is limited to the cost of repairing or replacing the
failed product or component at the discreon of IWS Global either within, or outside of warranty periods,
and does not extend to any loss or damage which may be caused as a consequence of misuse or failure of
the equipment or product or the informaon contained herein. IWS Global shall not in any event be liable for
economic loss of prots, indirect, special, bodily injuries or consequenal damages.
Specicaons and images are for illustraon purposes only. Final product may dier and is subject to change
without noce.

INSTRUCTION MANUAL
STEP 1 - Unpacking the iQ 20 Cart
Aer unpackaging, open the sliding lid.
Undo the two knobs to release the cable
management bracket.
Remove the Baskets and the accessories box.
Aer undoing the two knobs, remove the cable
management bracket from the iQ 20 Cart.
NOTE: If you are supplying your own cables, follow Step 2 to install.
If you purchased the Cart with cables pre-installed, go to Step 3.
STEP 2 - Roung the device cables
Connect the device cables to each USB port of the
iQ 5 Sync Charge Box (there are 2 iQ 5 Sync Charge
Boxes per side, 4 in total).

iQ 20 Cart
Insert the device cables into the cable management bracket.
Important: To ensure correct external LED status indicaon (on the top frame of the Cart), cables should be
connected to the correct USB ports on the iQ 5 Sync Charge Boxes (see image below).
Push the excess cable down behind the cable
management bracket and ensure enough cable is
pulled through the bracket (depending on device).
Fit the cable management bracket back into the
correct posion and replace and ghten the
knobs to secure the bracket.
Repeat on the opposite side of the Cart for the remaining 10 devices.

INSTRUCTION MANUAL
Insert your devices into the 5-slot Carry Baskets.
Place the Baskets in the Cart and connect the
device cables to each device.
STEP 3 - Connecng your devices and locking the Cart
Close the sliding top lid and aach a padlock to
secure your devices inside. IMPORTANT: Ensure
the cables are safely out of the way when closing
the sliding top lid.
PLEASE NOTE: For security, close the sliding lid,
swing the handle closed and lock the padlock. The
devices can sync and charge with the sliding top
lid closed.
To operate the wheel brake, push the “ON” brake
lever down in the “ON” posion.
to release the brake, push the “OFF” brake lever in
the “OFF” posion (the “ON” lever will ick back up).

iQ 20 Cart
To charge your devices, unwind the power cable
and plug it into the wall socket. Then plug the
power cable into Cart. Charging will automacally
start (may need to switch the wall outlet “on”).
When not in use, wrap excess power cable around
the cable cleat of the Cart.
STEP 4 - Syncing and Charging your devices
To sync your devices, connect your Macbook or
PC to the iQ 20 Cart with the provided USB-A to
USB-B cables.
PLEASE NOTE:
The USB-B end connects to the iQ Cart. The USB-A
end connects to your Macbook or PC.
Follow the instrucons from Apple congurator,
iTunes or other soware to sync your devices.
Devices will connue to charge during syncing.
LED Status: Refer to the included iQ 5 Sync Charge Box instrucons
The LED’s on top of the iQ 20 Cart frame indicate the current status of each port and device.
NOTE: The LED indicators for the charge-sync sequence are printed on the top of the sliding tray (see below).
Solid red: Ready to charge.
Flashing red: Idenfying device.
Follow the addional instrucons for the iQ 5 Sync Charge Box supplied,
for operaon of the syncing and charging funcons.
Flashing yellow: Host available.
Device not connected.
Solid yellow: Device connected.
Ready to sync.
Flashing green: Charging device.
Solid greed: Device ready to use.

INSTRUCTION MANUAL
Tools required:
• Masonry hammer-drill
• 10mm masonry drill bit
• Pencil and ruler/tape
• Hammer
• 13mm and 17mm spanners
The Security Chain Kit contains the following:
• 1 x 3 holed Anchor Plate and security chain
• 3 x 55mm long, 8mm Anchor Bolts
• 3 x Shear Nuts and washers
• 1 x Lock and key set
STEP 5 - Installing the Security Chain Kit.
Move the Cart to where you intend to store and secure it. It is best if the Floor Plate is as close as possible
to a wall to reduce the hazard of tripping and injury.
Aach the end of the chain to the steel loop with the padlock and posion the plate end in the desired
posion on the oor.
(NOTE: If mounng on carpet you will need to cut out the carpet from the area where the oor plate
aaches, otherwise the carpet will wrap around the drill when drilling).
Mark the center of each of the
3 holes, using the oor plate as
a guide.
Drill a 10mm hole through each
of the 3 marked centers to a
depth of 50mm.
Insert the anchor bolts with nut
aached into the holes through
the oor plate. Using the 13 mm
spanner, progressively ghten
down each of these anchor nuts
so that all three bolts are rmly
anchored into the concrete.
Now undo each of the three nuts, and in their
place thread on the three silver shear-nuts.
Ensure that the ‘cone’ is down and the hexagonal
nut is up. Using the 17mm spanner ghten down
the three shear nuts unl the hexagonal ‘head’
shears o, leaving just the cone ‘base’.
Aach the security chain through the steel loop
under the side of the Cart using the padlock.

www.pclocs.com.au www.lockncharge.com
Warranty
PC Locs/LocknCharge warrants the product to be free of defects in design, materials, assembly and crasmanship
for a period of twelve months from the date of purchase to the original retail purchaser. Evidence of original
purchase will be required to obtain warranty service.
In the event that a defect, malfuncon or failure occurs or is discovered during the warranty period,
PC Locs/LocknCharge will repair or replace, at its opon, the products which in the reasonable judgment of PC
Locs/LocknCharge are deemed defecve. All transportaon costs shall be borne by the owner and the risk of
loss shall be upon the party iniang the transportaon.
The warranty does not apply to any product that has been subject to misuse, tampering, neglect, or accident or as
a result of unauthorized alteraons or repairs to the product. The warranty is in lieu of all warranes expressed or
implied, including the implied warranes of merchantability and tness for a parcular purpose which are expressly
excluded or disclaimed. In no event will PC Locs/LocknCharge, their directors, ocers, employees, or agents be
liable for any harm, consequenal, incidental, third party, special or indirect damages whatsoever arising out of the
use or inability to use the products even if PC Locs/LocknCharge has been advised of the possibility of such damages.
PC Locs/LocknCharge obligaon is strictly and exclusively limited to the replacement or repair of any defecve
products. Some states do not allow the exclusion or limitaon of incidental or consequenal damages, so the
above limitaon or exclusion may not apply to you.
Compliances and Approvals
CE (Europe)
SAA (Australia)
UL Compliant (USA and Canada)
KCC (Korea) - pending
SIRIM (Malaysia) - pending
SPRING (Singapore) -pending