PCE Instruments PCE-SC 43 User manual

© PCE Instruments
PCE-SC 43 Sound Calibrator
User Manual
User manuals in various languages (français,
italiano, español, português, nederlands, türk, polski,
русский, 中文) can be found by using our
product search on: www.pce-instruments.com
Last change: 10 January 2022
v1.0
English

© PCE Instruments
Contents
1Safety notes........................................................................................... 1
2Specifications........................................................................................2
3Delivery scope.......................................................................................2
4Device description ................................................................................ 3
5Start-up and operation ......................................................................... 4
5.1 Inserting and replacing the batteries................................................................................. 4
6Troubleshooting....................................................................................4
7Warranty.................................................................................................5
8Disposal ................................................................................................. 5

© PCE Instruments
1
1 Safety notes
Please read this manual carefully and completely before you use the device for the first time. The
device may only be used by qualified personnel and repaired by PCE Instruments personnel.
Damage or injuries caused by non-observance of the manual are excluded from our liability and
not covered by our warranty.
•The device must only be used as described inthis instruction manual.If used otherwise,
this can cause dangerous situations for the user and damage to the meter.
•The instrument may only be used if the environmental conditions (temperature, relative
humidity, …) are within the ranges stated in the technical specifications. Do not expose
the device to extreme temperatures, direct sunlight, extreme humidity or moisture.
•Do not expose the device to shocks or strong vibrations.
•The case should only be opened by qualified PCE Instruments personnel.
•Never use the instrument when your hands are wet.
•You must not make any technical changes to the device.
•The appliance should only be cleaned with a damp cloth. Use only pH-neutral cleaner,
no abrasives or solvents.
•The device must only be used with accessories from PCE Instruments or equivalent.
•Before each use, inspect the case for visible damage. If any damage is visible, do not
use the device.
•Do not use the instrument in explosive atmospheres.
•The measurement range as stated in the specifications must not be exceeded under
any circumstances.
•Non-observance of the safety notes can cause damage to the device and injuries to
the user.
We do not assume liability for printing errors or any other mistakes in this manual.
We expressly point to our general guarantee terms which can be found in our general terms of
business.
If you have any questions please contact PCE Instruments. The contact details can be found at
the end of this manual.

© PCE Instruments
2
2 Specifications
Sound pressure level
94 dB, 104 dB, 114 dB
Accuracy
±0.4 dB
Class
2
Frequency
1000 Hz for A, B, C and D
frequency weighting
Frequency accuracy
±1.7 %
Stabilisation time
10 s
Total harmonic distortion
<3 %
Environment
Temperature / humidity influences
<0.4 dB at 0 ... 40°C / 32 ... 104 °F
and 25 ... 90 % RH
Atmospheric pressure influence
<0.1 dB at 65 ... 108 kPa
Stability at <60 s
±0.15 dB
Stability after one year
(normal use)
±0.35 dB
Operating conditions
0 ... 40 °C / 32 ... 104 °F, <25 ... 90 % RH,
non-condensing
Storage conditions
-20 ... 50 °C / -4 ... 122 °F, <90 % RH,
non-condensing
Automatic power off
after 20 minutes
Power supply
2 x 1.5 V AA battery
Battery life
approx. 50 h
Microphone size
1 / 2 inch
Dimensions
60 x 130 x 37.5 mm / 2.3 x 5.1 x 1.4"
Weight
400 g / 14.1 oz
3 Delivery scope
1 x PCE-SC 43
2 x 1.5 V AA battery
1 x user manual

© PCE Instruments
3
4 Device description
1. On / off key
2. Operating status LED green/red
3. Test chamber
4. dB range key
5. Green 94 dB status LED
6. Green 104 dB status LED
7. Green 114 dB status LED
8. Battery compartment
1
5
6
7
4
3
8
2

© PCE Instruments
4
5 Start-up and operation
Before you switch on the calibrator, it must acclimatise to the ambient conditions for at least two
hours. Then connect the calibrator to a sound level meter. Make sure that the sound sensor of
the sound level meter is completely inside the calibrator. Now switch on the calibrator with the
on/off key. It will first carry out a function test. This process takes about 10 seconds. During the
function test, the status LED flashes. As soon as the status LED glows continuously, the
calibration can be carried out.
To select between the individual sound levels, press the dB range key several times until you
have reached your desired sound pressure level. The sound pressure level is indicated by the
status LED lighting up.
After you have calibrated the sound level meter, first switch off the calibrator by pressing the on /
off key. Then you can detach the sound level meter from the calibrator.
Note:
The calibrator must be on a straight surface during a measurement. Both calibrator and sound
level meter must not move during a measurement. Make sure that the calibrator is not exposed
to loud noises or general vibration during calibration. This may affect the calibration.
5.1 Inserting and replacing the batteries
To put the calibrator into operation, first insert the batteries into the battery compartment on the
back. Use two 1.5 V AA batteries. Observe correct polarity when inserting the batteries. Then
close the battery compartment. Assoon as the total battery voltage is<2.2 V, the operating status
LED lights up in red. Then replace the batteries for proper operation. If the operating status LED
lights up in green, the calibrator is ready for operation.
6 Troubleshooting
Error
Cause
Solution
Function test is not
completed
Hardware faulty
Contact PCE Instruments
customer support.
Status LED is red
Battery voltage too low
Replace the batteries with
new ones. The total battery
voltage must be above 2.2
V.
Calibrator does not switch on
- Batteries completely
discharged
- Batteries not inserted
- Hardware faulty
- Replace the batteries
- Contact PCE Instruments
customer support

© PCE Instruments
5
7 Warranty
You can read our warranty terms in our General Business Terms which you can find here:
https://www.pce-instruments.com/english/terms.
8 Disposal
For the disposal of batteries in the EU, the 2006/66/EC directive of the European Parliament
applies. Due to the contained pollutants, batteries must not be disposed of as household waste.
They must be given to collection points designed for that purpose.
In order to comply with the EU directive 2012/19/EU we take our devices back. We either re-use
them or give them to a recycling company which disposes of the devices in line with law.
For countries outside the EU, batteries and devices should be disposed of in accordance with
your local waste regulations.
If you have any questions, please contact PCE Instruments.

© PCE Instruments
6
PCE Instruments contact information
Germany France Spain
PCE Deutschland GmbH PCE Instruments France EURL PCE Ibérica S.L.
Im Langel 26 23, rue de Strasbourg Calle Mayor, 53
D-59872 Meschede 67250 Soultz-Sous-Forets 02500 Tobarra (Albacete)
Deutschland France España
Tel.: [phone] Téléphone: [phone] Tel. : [phone]
Fax: [phone] Numéro de fax: [phone] Fax: [phone]
[email protected] [email protected] [email protected]
www.pce-instruments.com/deutsch www.pce-instruments.com/french www.pce-instruments.com/espanol
United Kingdom Italy Turkey
PCE Instruments UK Ltd PCE Italia s.r.l. PCE Teknik Cihazları Ltd.Şti.
Unit 11 Southpoint Business Park Via Pesciatina 878 / B-Interno 6 Halkalı Merkez Mah.
Ensign Way, Southampton 55010 Loc. Gragnano Pehlivan Sok. No.6/C
Hampshire Capannori (Lucca) 34303 Küçükçekmece - İstanbul
United Kingdom, SO31 4RF Italia Türkiye
Tel: [phone] Telefono: [phone] Tel: [phone]
Fax: [phone] Fax: [phone] Faks: 0212 705 53 93
[email protected] [e-mail] in[email protected]
www.pce-instruments.com/english www.pce-instruments.com/italiano www.pce-instruments.com/turkish
The Netherlands United States of America
PCE Brookhuis B.V. PCE Americas Inc.
Institutenweg 15 1201 Jupiter Park Drive, Suite 8
7521 PH Enschede Jupiter / Palm Beach
Nederland 33458 FL
Telefoon: [phone] USA
[email protected] Tel: [phone]
www.pce-instruments.com/dutch Fax: [phone]
[email protected]
www.pce-instruments.com/us