PDQ 3100 User manual

TO 85° MAX TO 90° MAX TO 95° MAX
TO 100° MAX
FOLD BACK
TO 110° MAX TO 105° MAX
STOP
MACHINE SCREWS:
USE #7 OR 13/64" [5.1] DRILL AND 1/4-20 TAP
WOOD DOOR/FRAME SCREWS:
USE 5/32" [4.0] DRILL
SEX NUTS:
USE 3/8" [9.5] DRILL
PARALLEL ARM INSTALLATION - PUSH SIDE - DS (NHO) AND DSHO (HO) APPLICATIONS - 110° MAX
3100/3101 DOOR CLOSER INSTRUCTION SHEET INSTRUCTION: 319354
REV. 2 09-05-19
MACHINE ONE
ADDITIONAL HOLE
AFTER INSTALLATION
OF BRACKET
MACHINE ONE
ADDITIONAL HOLE
AFTER INSTALLATION
OF BRACKET
FOLD AT HINGE/PIVOT CENTERLINE
FOR THE REQUIRED STOP/HOLD
OPEN ANGLE .
STOP
BRACKET
(RH DOOR)
BRACKET
(LH DOOR)
THIS SIDE UP
FOR LH DOOR
THIS SIDE UP
FOR RH DOOR
UNDERSIDE OF
SOFFIT / STOP
UNDERSIDE OF
SOFFIT / STOP
CLOSER BODY (LEFT HAND)
CLOSER BODY (RIGHT HAND)
SWEEP/ LATCH VALVES
THIS END OF CLOSER BODY
FOLD HERE, POSITION ON DOOR,
AND ALIGN WITH BOTTOM OF STOP (RH)
FOLD HERE, POSITION ON DOOR,
AND ALIGN WITH BOTTOM OF STOP (LH)
FOLD BACK FOLD BACK FOLD BACK FOLD BACK FOLD BACK
HINGE/PIVOT
ALIGN WITH
CENTERLINE
HINGE/PIVOT
ALIGN WITH
CENTERLINE
HINGE/PIVOT
ALIGN WITH
CENTERLINE
HINGE/PIVOT
ALIGN WITH
CENTERLINE
HINGE/PIVOT
ALIGN WITH
CENTERLINE
STOP MAY OCCUR APPROX. 3° TO 5° BEYOND
POSITION NOTED (DUE TO COMPRESSION OF CUSHION)
HINGE C
L
A
B
2 1/8" [54.0]
5/8" [15.9]
9 1/16" [230.2]
3/4" [19.1]
BOTTOM OF STOP
PUSH SIDE FACE
OF DOOR
FOLD HERE (LH)
FOLD HERE (RH)
FOLD HERE (LH)
FOLD HERE (RH)
OPENING
TO 90°
TO 95°
TO 100°
DIM A
6-5/16" [160.3]
5-3/4" [146]
5-1/8" [130.2]
DIM B
7-13/16" [198.4]
7-1/4" [184.2]
6-5/8" [168.3]
TO 105°
TO 110°
4-9/16" [115.9]
3-15/16" [100]
6-1/16" [154]
5-7/16" [138.1]
8-7/16" [214.3]6-15/16" [176.2]TO 85°
2 15/16" [74.6]
PDQ Manufacturing
2230 Embassy Dr.
Lancaster, PA 17603
833-273-7832
833-2 PDQTECH
www.pdqlocks.com

BACKCHECK
LATCH
SPEED
CONTROL
SWEEP SPEED
CONTROL
DOOR WIDTH APPROX. 360° TURNS
SIZE INTERIOR EXTERIOR 3100 3101
BF BF ON 36" -- -- -16 (CCW)
1 28" [711.2] -- -- -11 (CCW)
2 32" [812.8] 28" [711.2] -- -6 (CCW)
3 36" [914.4] 32" [812.8] 0 (PRESET) 0 (PRESET)
4 42" [1006.8] 36" [914.4] +5 (CW) +5 (CW)
5 48" [1219.2] 42" [1006.8] +9 (CW) --
6 54" [1317.6] 48" [1219.2] +12 (CW) --
COVER
PINION COVER
DUST
CAP
INSTALL DUST CAP:
1. Press dust cap over
bottom closer pinion.
INSTALL COVER (Optional):
1. Orient cover so cutouts
align with closer
pinion.
2. Slide pinion cover
into bottom cutout.
3. Slip cover over closer
until flush with door face.
4. Secure with screw provided.
LH RH
PREPARE DOOR AND FRAME:
1. Determine maximum opening angle.
2. Determine door hand (LH or RH).
3. Align & attach
full size template
(see reverse side).
4. Mark door & frame
with center punch.
5. Remove template before
machining door & frame.
3100/3101 DOOR CLOSER INSTRUCTION SHEET
PARALLEL ARM INSTALLATION - PUSH SIDE - DS (NHO) AND DSHO (HO) APPLICATIONS - 110° MAX
INSTRUCTION: 319354
REV. 2 09-05-19
ADJUST SPRING POWER:
1. Use 4 mm hex key provided to adjust to size on chart.
Clockwise (CW) turns increase spring power (+).
Counter-clockwise (CCW) turns decrease spring power (-).
3101 Series closers can be adjusted to meet
ADA Barrier Free (BF) applications. Compliance with ADA/BF
requirements may result with door not fully closing and latching.
Check with local AHJ. Closer size may vary due to site conditions.
6
1. Confirm this sheet is correct for your product and application.
2. Read the complete instruction sheet before starting installation.
3. Incorrectly installed or adjusted door closers can cause
personal injury or property damage.
4. To ensure safe operation closers should be examined
and serviced, regularly.
TOOLS REQUIRED:
1. Power drill
2. 14mm box/combo wrench
3. Phillips screw driver
4. #7 or 13/64" drill bit and
1/4-20 tap (machine screws)
5. Tap handle
6. 5/32" drill bit (wood screws)
7. 3/8" drill bit (sex nuts)
8. Center punch
1. See reverse side of this sheet to machine door & frame.
2. Dimensions based on 4-1/2" x 4-1/2" full mortise butt hinges
with 5/8" stop and 1/8" door gap.
3. Confirm door & frame are properly reinforced.
4. Sex nuts required for un-reinforced or composite fire doors.
5. Do not install closer on the exterior (weather) side of building.
1
2
3
4
5
SLOWER
FASTER
INCREASE
DECREASE
1. Use hex key provided.
2. Adjust SWEEP (closing max.°- 10°).
3. Adjust LATCH (closing 10°- 0°).
4. Adjust BACKCHECK resistance (opening 70°- max.°).
DO NOT COMPLETELY CLOSE VALVE
5. Adjust (optional) DELAYED ACTION (closing max.°- 70°);
Provides additional hesitation for access (ADA/BF) through door.
CONTROL ADJUSTMENTS:
Closing time of 3-7 seconds is typical.
More time may be needed for ADA/BF access.
Clockwise (CW) = SLOWER.
Counter-clockwise (CCW) = FASTER.
DO NOT REMOVE VALVES
CLOSING CYCLE
Y
A
L
E
D
E
E
W
S
P
H
C
T
A
L
MAX.°
K
C
A
B
C
E
H
C
K
N
E
P
O
I
N
G
OPENING CYCLE
MAX.°
7
8
9
PDQ Manufacturing
2230 Embassy Dr.
Lancaster, PA 17603
833-273-7832
833-2 PDQTECH
www.pdqlocks.com
INSTALL CLOSER AND ARM:
1. Attach closer body to door. Sweep & latch
valves point away from hinges.
2. Install bumper stop into DS bracket.
Bracket is stamped:
"L"(left hand) and "R"(right hand).
3. Install filler plug into other hole.
4. Install DS bracket and spacer
block to frame.
45°
R
L
S
SPINDLE
ARM
4. Close door & rotate closer
spindle 45° toward hinge / pivot.
5. Install arm parallel to door face,
pointing away from hinge.
6. Secure arm to closer spindle.
RH DOOR SHOWN
5300/5500 DOOR CLOSER MODELS INSTRUCTION SHEET TEMPLATE: 539354,
REV. 0 01-19-17
CLOSER BODY (LEFT HAND DOOR)
CLOSER BODY (RIGHT HAND DOOR)
THIS SIDE UP
FOR RH DOOR
BRACKET
(LH DOOR)
BRACKET
(RH DOOR)
THIS SIDE UP
FOR LH DOOR
PARALLEL ARM INSTALLATION - PUSH SIDE - DS AND DSHO APPLICATIONS
OPTIONAL HOLD OPEN:
1. DSHO arm has an optional
thumb turn "T" handle.
2. A 1/4 rotation of "T" engages
or disengages hold open.
3. Door can also be
manually pulled
in and out of hold open
without rotating the "T" handle.
4. Greasing detent ball is recommended
to prevent wear.
HOLD
OPEN
"T" HANDLE
HINGE
BUMPER
STOP
FILLER
PLUG
LH
RH
CW
CCW
(-) (+)
SPRING POWER
ADJUSTING NUT
HEX
KEY
PINION/
SPINDLE
SPACER
BLOCK
DS
BRACKET
CLOSER
BODY