Pecron S200 User manual

ShenZhen Pecron Technology CO.,LTD.
Outdoor Portable Power Station Specification
Model：S200
Thanks for choose our outdoor portable power station S200
Please read the manual carefully before you use!
Shenzhen Pecron Technology Co.,Ltd
Http://www.pecron.com

Content
1. Introduction：....................................................................................................................................... 1
2. Panel Function Description：.......................................................................................................... 2
3. Product Specification：..................................................................................................................... 4
4. Environmental Conditions：............................................................................................................ 4
5. Electrical Specifications：................................................................................................................. 5
5.1-5.4 Specifications...................................................................................................................... 5
5.5-5.6 Protection Instructions..................................................................................................... 6
6. Operating Instructions And Precautions：................................................................................ 7
6.1 How To Use AC.............................................................................................................................7
6.2 How To Operate........................................................................................................................... 8
6.3 How To Charge............................................................................................................................. 9
6.4 How To Use DC 12V and USB...................................................................................................9
7. Product Function Test：................................................................................................................. 10
7.1 Test Conditions...........................................................................................................................10
7.2 Basic Function Test Display.....................................................................................................11
8. Misuse And Countermeasures......................................................................................................12
9. Package................................................................................................................................................. 12
10. After Sales Service.......................................................................................................................... 13

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 1 -
1. Introduction
pecron S200 is a functional outdoor portable power station,it has safe Lithium-ion battery
and invertor conversion technology,with light weight,high capacity,high power function,to
provide portable power solutions,its main function is as below:
♦220V50Hz or 110V60Hz pure sine wave output
♦9~12.6V8A（MAX 15A）DC output,USB 5V1A、5V2A、QC3.0 output port
♦LED Emergency Light
♦Battery capacity display screen
♦Support solar charging,car charging(solar cable and car charging cable is optional)
S200 can be used in series smart products,such as mobile phones,satellite
telephone,digital camera,mobile driver,digital camera,tablet,car start,outdoor
illumination,water pump,post and telecommunications,medical device,and it also can use
in these area:financial,first aid,dig,exploration,military, science, media, tourism, disaster
relief, medical assistance and areas with widespread power shortages.
Please read the user manual carefully before you use,and please save it with the purchase
certificate for future reference.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 2 -
2. Panel Function Description
①Battery display：Power display screen:The number shows current remain power,the
single digit flashing when it is charging,when the remain power lower than 10%,the single
digit and tens digit flashing at the same time.
②AC indicator:When the AC output switch is on,the indicator is green,when the AC output
turn off,the indicator will off.When the remain power lower than 10%,the indicator will
change to red.
③USB output/Power switch：Press this button to view the remaining power of the power
unit. And the display turns on, as same as the USB output. Press and hold this button for 2
seconds to forcibly switch the USB output. The default USB is automatic detection.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 3 -
④USB DC ouput：When there is no load, it will automatically enter the sleep state to turn
off the output, and automatically turn on when connected to the load.(A.USB 5V1A,B.USB
5V2A,C.USB QC3.0:12V1.5A 9V2A 5V2.1A)
⑤DC input：Support wide voltage 13V-30V4A(MAX) charging,support car charging,solar
charging,input port is DC5521 port,max power is 50W.
⑥DC 5525 port：It can supply DC device 9~12.6V8A（MAX 15A）
⑦LED Switch：Press the switch,Led light will turn on
⑧LED Light
⑨AC Switch： When the AC switch turn on,the AC output will work,turn of the switch,AC
output will shut down.
⑩AC socket： When the AC switch turn on,it will work,AC output is 220V or 110V.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 4 -
3. Product Specification
NO.
Introduction
S200
1
Rated Power
200W
2
Peak Power
400W
3
Output Voltage
220V/50Hz or AC110V60Hz
DC 9~12.6V8A（MAX 15A） 5V1A 5V2A QC3.0
4
Output
Waveform
Pure Sine Wave
5
Battery Type
18650-7P3S( 3.6V 2.55Ah)
6
Battery Capacity
192.78Wh（10.8V17.85Ah）
7
Battery Type
Lithium-ion
9
Charging Time
5~ 6H
10
Input Voltage
And Current
DC 13~30V 4A（MAX）， Solar Charging 18V
11
Protection
Over Voltage、Low Voltage、Over Temperature、Over
Load、Short Circuit
12
LED
1W*2
13
Working
Temperature
0℃~45℃（Charge）
-20℃~60℃（Discharge）
14
Product
Dimension
L190*W127*H175mm
15
Shell Material
UL94-V0 PC+ABS
16
Net Weight
2kg

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 5 -
4. Environment Condition
5. Electrical Specifications
5.1-5.4 Specifications
NO.
Test Project
Specification
Unit
Remark
1
Working Temperature
0 ~ 45
℃
2
Storage Temperature
-20 ~ 60
℃
3
Humidity
45% ~ 85%
RH
4
Cooling type
Air-cooled
Cooling≥45℃
5
Altitude
3000
m
6
Mean time between failures
≥5000
H
NO .
Test Project
Specification
Unit
Remark
5.1
AC Charging
5.1.1
Rated Voltage
100 ~ 240
VAC
5.1.2
Rated Power
50/60
Hz
5.1.3
Input Voltage
15
VDC
5.1.4
Input Current
4
A
5.2
Solar Charging
5.2.1
Voltage
13~30
VDC
5.2.2
Current
≤4
A
5 .3
AC Output
5.3.1
Rated Voltage
230/110±5%
VAC
5.3.2
Rated Frequency
50/60±1%
Hz
5.3.3
Rated Power
200
W
5.3.4
Harmonic distortion
＜3%
5.3.5
Conversion efficiency
≥85%
5.4
DC Output
5.4.1
USB Voltage
5/QC3.0(4-12
)
VDC
5.4.2
USB Current
2.0（MAX）
A
5.4.3
5525 DC Output Voltage
9~12.6
VDC
5.4.4
5525 DC Output Current
8
A

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 6 -
5.5-5.6 Protection Instructions
NO .
Test Project
Specification
Unit
Remark
5.5.1
Over charge,over discharge,over load ,over temperature,short circuit
5.5.2
Over voltage
4.2 V
VDC
5.5.3
Low voltage
＜2.8V
VDC
5.5.4
Over temperature
Inverter
cooling≥65℃
℃
Lock，No output,Until the
temperature drops
5.5.5
Over load
300
W
Locked, no output, until
disconnected
5.5.6
Output short Circuit
—
W
Locked, no output, until
disconnected
Remark
When 5.5.3 5.5.4 5.5.5 in the protection state, the AC current switch needs
to be turned off. When it is turned on again, the DC output will be turned on.
5.6
DC Output
5.6.1
USB Over Current
3
A
5.6.2
5525 Over Current
15
A
6. Operating Instructions And Precautions
To make sure safety transportation,when you receive the power station,the power
station is under low capacity status,please charge the power station to full capacity before
you use.
If you need to full charge the power station,please use our standard power adapter for
S200,or use 18V 50W solar panel to charge it.
During charging, the battery level is flashing. When the power supply is fully charged,
the power indicator light is on, and the S200 power supply is fully charged.
To make sure safety,please use our standard charger,when PECRON-S200 is full
charge,please disconnect the charger.
6.1 How To Use AC
S200 is a power station which with rated power 200W,220V50HZ/110V60HZ pure sine
wave output.Please note the following before using:

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 7 -
（1）Please make sure the input voltage and frequency is same as S200
（2）Please make sure the appliance rated power is lower than 200W.
* If you violate these,the charger may damage or out of work.
* If your appliance power higher than 200W,please choose other higher power portable
power station.
Remark：Because when some appliances turn on,its consumption power is higher than
the rated power,such as sensitive load device start up current normally is 3-8 times than its
rated power,Energy-saving lamps start up power is dozens of times than its rated power,if
their start up power is higher than the emergency power station’s peak power,it will
trigger the over load protection,and shut down the power station.The S200 is with over
load,short circuit,over temperature protection.
(3)When the following happens,S200 will stop output to protect the appliance:
①When the appliance load power is higher than the power station rated power.
②AC output or appliance circuit
③The internal temperature of power station is too high
④The internal battery voltage is too low
6.2 How To Operate
Step 1:Turn on the AC switch,the battery display screen will turn on automatically,and
shows the remaining capacity.
Step 2:Check load input voltage and frequency.
Step 3:Check load power,and make sure it won’t over S200 rated power.
Step 4: Connect the appliance to S200,turn on the AC switch.
Step 5:After use the power station,press the AC switch to shut down the AC output.
Step 6:If the power station capacity use off or the remaining capacity is too low,please
recharge S200 for your next use.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 8 -
(Note:When you stop using the power station,please turn off the AC switch.If not,the S200
will be in a high-energy self-consumption mode, consuming the stored power of the
power supply. )
6.3 How To Charge
S200 rated power is 200W,battery capacity is 10.8V/17.85AH,we can use the follow
charging types to charge the battery.
+ =
（1）
（1）Use our standard power adapter,when we start to charge,we need to use the power
cord to connect with the adapter,and the adapter another side will connect to the power
station input charging port,then plug to the grid.
（2）Use our car charging cable,when you use car charging,after you start up the car,and
then just insert the cigar connector to the car cigar port,the other side connect to the
power station input port.When the car is not on start up status,please don’t use car
charge.
（3）Solar charging,when you use solar panel to charge the power station,please use the
solar cable to connect the solar panel,and the other side connect to the power station
input port.(Please make sure solar panel max voltage not over 30V,Min voltage not lower
than 13V.)
Note：
①Our S200 standard power adapter only use in our S200,please don’t use in other
device and keep away from rain.
②When the portable power is left unused for a long time, the battery will run out. Please
make sure to charge it every six months.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 9 -
6.4 How To Use DC 12V and USB
=> DC 12V,rated current 8A.overload current 15A，please make sure
the connect can bear big current when you use big current,to prevent the connector
temperature too high to damage the power station.
=> 5V1A、5V2A、QC3.0，connect the USB
cable and connect to the device,the USB will turn on automatically.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 10 -
7. Product Function Test
7.1 Test Condition
No
.
Project
Test condition
Check item
1
High-altitude
test
1. Pressure≤=11.6Kpa，T =20±5℃
2. No package,no electricity
1. Appearence
2.Power performance
2
Temperature
test
1. Temperature between 40±2℃ and 75±2℃
2. Repeat the test 10 times
3. Switching time is 30 minutes
1. Appearence
2.Power performance
3
Vibration test
Amplitude：1.52mm，
Scanning frequency range：5Hz ~ 10Hz， Scan
speed： About 10 ㎡/ S3,
Scanning frequency range：0Hz〜200Hz，Scan
speed：About 3 ㎡/ S3，
Scanning frequency range：200Hz ~ 500Hz，Scan
speed：About 1 ㎡/ S3，
The duration of each vibration is 20 minutes. It
vibrates from all directions of the X, Y and Z axes.
The appearance of the power supply is free of any
signs of damage. The product can pass each
function test, and the product identification text is
clear, complete, and clear. There is no shaking or
squeaking noise; the screws are fastened firmly
and there are no sliding teeth.
1. Appearence
2.Power performance

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
Shenzhen Pecron Technology Co.,Ltd http;//www.pecron.com Tel：[phone]
- 11 -
7.2 Basic Function Test Display
7.2.1 Discharge test under load 7.2.2 Charge test
7.2.3 12V 5525 output current test 7.2.4 USB port output current test
7.2.5 LED test

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
- 12 -
8. Misuse And Countermeasures
Error
Root
Solution
Press any switch,no display
and output
Interior battery protect
Charge up
No AC output after pressing
AC switch
（Alarm on）
Over temperature
Disconnect the load and
start to work it after the
temperature is lowered
Over load
Check the loading power and
decrease it
Low voltage
Charge up
USB no output
Battery display button switch
is not open
Press the battery display
button
12V or USB DC consume
energy quickly
AC switch is on; standby
current is too large
Turn off AC switch during DC
output
Not full charged by solar
panel charger
1.The solar panel is not
suitable
2.Sunshine is not enough
Choose another solar panel
that is much more suitable.
And ensure that the charging
voltage is higher than 13V.
The display does not go out
1. Forced USB is enabled
2. AC is turned on
1. Press and hold the power
switch for 2 seconds to
forcibly turn off the USB
output
2. Turn off the AC switch
The battery is not displayed
or crashed
Interference or self-standby
loss
press and hold the battery
display button for more than 6
seconds

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
- 13 -
9. Package
NO .
Package Content
Quantity
1
S200 power station
1
2
Power adapter
1
3
Car charging cable
1
4
Cigar port
1
5
Solar cable（Optional）
1
6
User manual and warranty card
1
Gross Weight（kg) ：2.84
Carton Size（mm) ：L292*W170*H233
Quantity（pcs )：1PCS/CTN
10. After Sales Service
All pecron portable power station warranty time is 12 month since the sales date.
During the warranty period, our company will be responsible for the defects on material
and process, we will change the damaged parts after receiving them back or maintain the
product for free once our technicians inspect that the breakdown occurs normally;But we
are not responsible for the following situations even though it’s during warranty period:
• Take apart the product
• Damage on surface coating and appearance.
• Breakdown due to wrong installation, packing and usage. Customers should do this
according to the manual instruction.

Shenzhen Pecron Technology Co.,Ltd
POWER IT POSSIBLE
- 14 -
•Breakdown or damage caused by accident, man-made and environment( misoperation,
crash, unsuitable voltage, damp and etc.)
•Breakdown or damage caused by natural hazard beyond control( earthquake, fire,
tsunami and etc.)
•Maintenance is not including package and products accessories;
•We will offer paid service once warranty period is over.