Pedigo P-2110 User manual

manual
operation & care
P-2110
P-2120
P-2130
120V
MM-1065 (MN-29614) • Rev 4 • 06/16Printed in the U.S.A.
P-2110
P-2120
P-2130
Fluid Warmers

MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Table of Contents
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Transportation Damage and Claims . . . . . . . . . . . . . . . . 1
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical Information . . . . . . . . . . . . . . . . . . . . . . . . 8
Operation Instructions . . . . . . . . . . . . . . . . . . . . . . . 9
Cleaning and Preventative Maintenance . . . . . . . . . . . . 12
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Wiring Diagrams . . . .Refer to the wire diagram included with the appliance.
Limited Warranty . . . . . . . . . . . . . . . . . . . . back cover
Pedigo Products, Inc. • 4000 S.E. Columbia Way • Vancouver, WA 98661 • U.S.A.
Phone: [phone] • Fax: [phone] • www.pedigo-usa.com

1
MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Delivery
The appliance has been thoroughly tested and inspected to
insure only the highest quality appliance is provided. Upon
receipt, check for any possible shipping damage and report
it at once to the delivering carrier. See Transportation
Damage and Claims section located below.
This appliance, complete with unattached items and
accessories, may be delivered in one or more packages.
Conrm that all standard items and options have been
received with each appliance as ordered. Save all the
information packed with the appliance.
This manual must be read and understood by all people
using or installing the appliance. Contact the service
department if there are any questions concerning
installation, operation, or maintenance.
Serial number is required for all inquiries.
Always include both model and serial number(s) in any
correspondence regarding the appliance.
Model: ______________________________________________
Serial Number: ______________________________________________
Purchased From: ______________________________________________
Date Installed: ____________________ Voltage: _____________
Transport and storage environmental conditions (not to exceed 15 days)
• Ambient temperature range of -40°C to +70°C (-40°F to +159°F)
• Relative humidity range of 10% to 95%, non-condensing
• Atmospheric pressure range of 50KPa to 106KPa
Operational environmental conditions
• Appliance must acclimate to room temperature in the environment it will be placed. 24 hours is recommended.
• Recommended environmental temperature range is 15°C to 32°C (60°F to 90°F).
• Recommended relative humidity is above 20%, non-condensing.
Environmental Conditions
Receipt of Appliance
All Pedigo Products, Inc. appliances are
sold F.O.B. shipping point, and when
accepted by the carrier, such shipments
become the property of the consignee.
Should damage occur in shipment, do not put the
appliance into service until the damage has been
inspected by an authorized service provider.
Should damage occur in shipment, it is a matter between
the carrier and the consignee. In such cases, the carrier
is assumed to be responsible for the safe delivery of the
merchandise, unless negligence can be established on the
part of the shipper.
1. Make an immediate inspection while the appliance
is still in the truck or immediately aer it is moved
to the receiving area. Do not wait until aer the
appliance is moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until
a proper count has been made and inspection of all
appliances are received.
3. Note all damage to packages directly on the carrier’s
delivery receipt.
4. Have the driver sign the delivery receipt. If he refuses
to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the
following on the delivery receipt: Driver refuses to
allow inspection of containers for visible damage.
6. Telephone the carrier’s ofce immediately upon
nding damage, and request an inspection. Mail
a written conrmation of the time, date, and the
person called.
7. Save any packages and packing material for further
inspection by the carrier.
8. Promptly le a written claim with the carrier and
attach copies of all supporting paperwork.
Pedigo will continue our policy of assisting our customers
in collecting claims which have been properly led
and actively pursued. Pedigo cannot, however, le any
damage claims, assume the responsibility of any claims,
or accept deductions in payment for such claims.
Transportation Damage and Claims

2MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Unpacking
1. Carefully remove the appliance from the carton or crate.
NOTE: Do not discard the carton and other packaging material
until the appliance has been inspected for hidden damage
and tested for proper operation.
2. Read all instructions in this manual carefully before initiating the
installation of this appliance, using the appliance or performing routine
maintenance. Following procedures other than those indicated in this
guide to use and clean the appliance is considered inappropriate and
may cause damage, injury or fatal accidents, in addition to invalidating
the guarantee and relieving the manufacturer of all liability.
3. Do not discard this manual. This manual is considered to be part of the
appliance and is to be provided to the owner or manager of the business
or to the person responsible for training operators. Additional manuals
are available from the service department.
4. Remove all protective plastic lm, packaging materials, and accessories
from the appliance before connecting electrical power. Store any
accessories in a convenient place for future use.

3
MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Safety Procedures
NOTICE: Used to notify personnel of installation,
operation, or maintenance information that is
important but not hazard related.
Used to indicate that referral to operating
instructions is a mandatory action. If not
followed, the operator or patient could suer
personal injury.
Used to indicate that referral to operating
instructions is recommended to understand
operation of the appliance.
Knowledge of proper procedures is essential to the
safe operation of electrically energized appliances. The
following hazard signal words and symbols may be used
throughout this manual.
CAUTION
Used to indicate the presence of a hazard that can or
will cause minor personal injury, property damage, or a
potential unsafe practice if the warning included with this
symbol is ignored.
DANGER
Used to indicate the presence of a hazard
that will cause severe personal injury, death,
or substantial property damage if the warning
included with this symbol is ignored.
WARNING
Used to indicate the presence of a hazard
that CAN cause personal injury, possible
death, or major property damage if the
warning included with this symbol is ignored.
CAUTION
Used to indicate the presence of a hazard
that can or will cause minor or moderate
personal injury or property damage if the
warning included with this symbol is ignored.
NOTICE: For appliances delivered for use
in any location regulated by the
following directive (2012/19/EU -WEEE):
Do not dispose of electrical or
electronic appliances with other
municipal waste.
• Fluid warmers are only intended for warming medical
solutions for irrigation and injection prior to their use.
Please refer to the labeling of the manufacturer of the
products to be warmed regarding the recommended
temperature and the duration of warming. No other use
for this appliance is authorized or recommended.
• This warmer is intended for use in commercial
establishments where all operators are familiar with
the purpose, limitations, and associated hazards of
this device. The warmer can be used wherever there
is appropriate space and electrical source including
patient support areas, ER, ICU, PACU, surgical suites,
patient rooms, and nursing stations.
• Operating instructions and warnings must be read and
understood by all operators and users.
• Any troubleshooting guides, component views, and
parts lists included in this manual are for general
reference only and are intended for use by qualied
technical personnel.
• This manual should be considered a permanent
part of the appliance. This manual and all supplied
instructions, diagrams, schematics, parts lists, notices,
and labels must remain with the appliance if it is sold or
moved to another location.
CAUTION
The door may swing during transport. Only
transport the appliance when the door is
closed and secure.
WARNING
Appliance and accessories may be
heavy. To prevent serious injury, always
use a suicient number of trained and
experienced workers when moving or
leveling appliance and handling accessories.
NOTICE: A temporary odor may be noticeable upon initial
start-up of the appliance. Contact manufacturer
if the odor persists aer a day or more of
continuous use.
CAUTION
This unit is not approved for
warming of blood or blood products.

4MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Installation
Preparation
Before operating the appliance, clean both the interior and exterior with a damp cloth and mild soap
solution. Wipe with an appropriate disinfectant. Wipe dry with a clean cloth or air dry.
DANGER
To prevent serious personal injury, death, or
property damage:
Do not steam clean, hose down or flood the
interior or exterior with water or liquid solution
of any kind. Do not
use water jet toclean. Failure
to observe this precaution will void the warranty.
DANGER
To prevent serious injury, death, or
property damage:
Do not use this warming appliance in
the presence of flammable anesthetic
mixtures (with air or with oxygen or
nitrous oxide).
Not category AP or APG equipment
Fluid warming chamber:
The warming appliance can be programmed to warm
either irrigation uids (IRR) or injection uids (INJ), with
separate temperature ranges provided depending on the
choice selected.
• IRR temperature range: 37°C to 66°C (98°F to 150°F),
• INJ temperature range: 37°C to 40°C (98°F to 104°F).
A fan located inside the chamber mixes the air to prevent
temperature stratication and to ensure an accurate
chamber temperature for each mode.
• Within +0/-1.12°C (+0/-2ºF) for set points of
37°C to 40°C (98°F to 104°F).
• Within +0/-1.67°C (+0/-3ºF) for set points of
43°C to 66°C (110°F to 150°F)
An alarm will sound if temperatures exceed 6°C (10°F) over
the set-point temperature, and an overtemp indicator will
blink indicating an over-temperature condition.
P-2110 Information:
General Information
P-2120 Information:
This warming appliance is designed to safely warm and
store either irrigation uids or injection uids.
The single-chambered warming appliance is constructed
with stainless steel exterior casing and door with handle
and hinges designed to withstand heavy usage. A door
with window allows observation of inventory. The cabinet
is warmed using a low-heat-density electrothermal cable
array. The electrothermal cable is positioned in the oor
and two sides of the warming cabinet, providing even
heating of the interior chamber.
The interior chamber temperature is regulated by
an electronic control consisting of a 4 digit LED
display, on/off button, increase and decrease buttons,
integrated lock-out control feature, and a series of
prompt sequence indicators.
The electronic control can be set to operate in fahrenheit
or celsius. Aer a power failure, the appliance will
remember its programming and begin to operate as
before. The on/off indicator will blink to indicate a
failure occurred; pressing the on/off button once will
eliminate this blinking. A thermal shut-off system,
separate from the electronic control, is included as an
additional safety feature.
The electronic control will display temperature in
whole degrees.
P-2130 Information:
Fluid warming chamber:
The warming appliance can be programmed to warm
either irrigation uids (IRR) or injection uids (INJ), with
separate temperature ranges provided depending on the
choice selected.
• IRR temperature range: 37°C to 66°C (98°F to 150°F),
• INJ temperature range: 37°C to 40°C (98°F to 104°F).
A fan located inside the chamber mixes the air to prevent
temperature stratication and to ensure an accurate
chamber temperature for each mode.
• Within +0/-1.12°C (+0/-2ºF) for set points of
37°C to 40°C (98°F to 104°F).
• Within +0/-1.67°C (+0/-3ºF) for set points of
43°C to 66°C (110°F to 150°F)
An alarm will sound if temperatures exceed 6°C (10°F) over
the set-point temperature, and an overtemp indicator will
blink indicating an over-temperature condition.
The appliance is equipped with three (3) white, epoxy-
coated wire baskets to accommodate uids packaged in
bags or bottles, mounted on basket rail supports. Each
basket has a capacity of 18 1-liter bottles (54 total) or 24
1-liter bags (72 total). The appliance is furnished with a
full perimeter rubber bumper assembly and one set of
5" (127mm) heavy-duty casters – two (2) rigid and two (2)
swivel with locking brake.
The appliance is equipped with two (2) white, epoxy-
coated wire baskets to accommodate uids packaged in
bags or bottles, mounted on basket rail supports. Each
basket has a capacity of 9 1-liter bottles (18 total) or 15
1-liter bags (30 total). The appliance is furnished with a
full perimeter rubber bumper assembly and one set of
5" (127mm) heavy-duty casters – two (2) rigid and two (2)
swivel with locking brake.
The appliance is equipped with one (1) white, epoxy-
coated wire basket to accommodate uids packaged in
bags or bottles, mounted on basket rail supports. The
basket has a capacity of 11 1-liter bottles or 16 1-liter bags.
The appliance is furnished with four (4) 1-1/4" (31mm)
non-skid rubber feet.

5
MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Dimensions
P-2110
38.9" (987mm)
22.8" (580mm)
19.4" (493mm)
13.8" (351mm)
CAVITY
1.2"
(31mm)
13.1" (333mm)
CAVITY
16.2" (410.4mm)
19.0" (475mm)
ELECTRICAL CONNECTION
21.5" (547mm)
CAVITY
28.0" (711mm)
17.5" (445mm)
11.9" (302mm)
43.0" (1092mm)
17.9" (453mm)
9.2" (233mm)
11.5" (292mm)
8.07"
(205mm)
CORD LENGTH (est.)
8' (2,438mm)

6MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Dimensions
P-2120
33.4" (849mm)
27.0" (685mm)
20.0" (508mm)
CAVITY
14.1" (359mm)
CAVITY
21.6" (549mm)
CAVITY
1.5" (37mm)
Electrical Connection
45.0" (1143mm)
28.5" (725mm)
24.3" (613mm)
8.7"
(221mm)
17.4" (441mm)
20.7" (525mm)
7.7
"
(195mm)
12.3 "
(312mm)
16.3 " (413mm)
CORD LENGTH (est.)
8' (2,438mm)

7
MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Dimensions
P-2130
11.0"
(280mm)
52.8" (1341mm)
35.0" (890mm)
28.0" (731mm) 11.0"
(280mm)
2.20" (55.6mm)
OFF
ON
30.10" (764mm)
25.10" (638mm)
5.5" (140mm)
18.9" (480mm)
Cavity
25.2" (639mm)
26.9" (684mm)
Cavity
35.1" (892mm)
40.8" (1036mm)
54.0" (1372mm)
33.876" (860.5mm)
22.3" (566mm)
22.1 " (561mm)
7.7"
(195mm)
17.1 " (434mm)
CORD LENGTH (est.)
8' (2,438mm)
26.6" (676mm)
Cavity

8MM-1065 (MN-29614) • Rev 4 • 06/16 • Pedigo Fluid Warmer
Electrical Information
Rating Tag
The power specication is located on the appliance identication rating tag. This tag is
permanently attached to the appliance and must be located to verify power requirements.
Hazardous
Voltage Present
CAUTION
Power source must match voltage identified
on appliance rating tag. The rating tag
provides essential technical information
required for any appliance installation,
maintenance or repairs. Do not remove,
damage or modify the rating tag.
DANGER
To prevent serious injury, death, or
property damage:
Do not use this warming appliance in
the presence of flammable anesthetic
mixtures (with air or with oxygen or
nitrous oxide).
Not category AP or APG equipment
P-2110
Safety Class I
Equipment
Protective Earth
Ground Symbol
Medical Equipment classied by Underwriters
Laboratories with Respect to Electrical Shock,
Fire and Mechanical Hazards only, in Accordance
with UL 60601-1 and CAN/CSA C22.2 No. 601.1.
UL File No.
E201645
Grounding reliability can only be achieved when appliance is
connected to an equivalent receptacle marked “Hospital Grade.”
Wire diagram is located under top lid of warmer.
Power Requirements
P-2120
P-2130
120 V.A.C. — 50/60 Hz, 1 ph
0.65 kW, 5.4 Amps
Safety Class I Equipment
No Applied Parts
Mode of Operation: Continuous
NEMA 5-15P
15A - 125V Plug
Hospital Grade IPX-0
120 V.A.C. — 50/60 Hz, 1 ph
0.78 kW, 6.4 Amps
Safety Class I Equipment
No Applied Parts
Mode of Operation: Continuous
NEMA 5-15P
15A - 125V Plug
Hospital Grade IPX-0
120 V.A.C. — 50/60 Hz, 1 ph
1.06 kW, 8.8 Amps
Safety Class I Equipment
No Applied Parts
Mode of Operation: Continuous
NEMA 5-15P
15A - 125V Plug
Hospital Grade IPX-0