Pedigo WARMWATCH P-2148 User manual

OPERATION & CARE
MANUAL
OPERATION & CARE
MM-1068 (MN-29617) • Rev 0 (10/15)
PRINTED IN U.S.A.
WARMWATCH® COMBINATION
BLANKET/FLUID WARMING CABINET
P-2145
P-2148
P-2140
P-2145

Environmental Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Transportation Damage and Claims . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking & Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Procedures and Precautions . . . . . . . . . . . . . . . . . . . . . . 3
Installation
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Electrical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Guidance and Manufacturer’s Declaration . . . . . . . . . . . . . . . . . . 10
Operating Instructions
Blanket Control Features . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Blanket Chamber Operational Procedures . . . . . . . . . . . . . . . . . . 12
WarmWatch®Fluid Control Features . . . . . . . . . . . . . . . . . . . . 13
Fluid Chamber Operational Procedures . . . . . . . . . . . . . . . . . . . 15
WarmWatch®USB Download Operation . . . . . . . . . . . . . . . . . . 16
WarmWatch®USB Download Reports . . . . . . . . . . . . . . . . . . . 17
Care and Cleaning
Cleaning and Preventative Maintenance. . . . . . . . . . . . . . . . . . . 18
Clean the Unit Regularly. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Service
Trouble Shooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Accessory Service Parts List . . . . . . . . . . . . . . . . . . . . . . . . 21
Heating Cable Replacement Kits . . . . . . . . . . . . . . . . . . . . . . 21
Full Assembly Parts List and Views . . . . . . . . . . . . . . . . . . . . . 22
Electrical Parts List & Views . . . . . . . . . . . . . . . . . . . . . . . . . 26
Wire Diagrams refer to wire diagram included with the unit (under top lid)
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
TABLE OF CONTENTS

MM-1068 (MN-29617) • Rev 0 (10/15) • WarmWatch® Combination Blanket/Fluid Warmer • 1
DELIVERY
The warming cabinet has been thoroughly tested and
inspected to insure only the highest quality unit is provided.
Upon receipt, check for any possible shipping damage and
report it at once to the delivering carrier. See Transportation
Damage and Claims section located below.
This appliance, complete with unattached items and
accessories, may be delivered in one or more packages.
Check to ensure that all standard items and options have
been received with each model as ordered.
Save all the information packed with the appliance. Complete
and return the warranty card to the factory as soon as
possible to assure prompt service in the event of a warranty
parts and labor claim.
This manual must be read and understood by all people
using or installing the equipment model. Contact the
service department if you have any questions concerning
installation, operation, or maintenance.
Always include both model and serial numbers in your correspondence
regarding the unit.
Model:
_____________________________________
Serial Number: _____________________________________
Purchased From: _____________________________________
Date Installed: ____________ Voltage: _______________
SERIAL NUMBER IS REQUIRED FOR ALL INQUIRIES
Transport and Storage Environmental Conditions (not to exceed 15 days)
•Ambient temperature range of -40° to +70°C (-40° to +159°F).
•Relative humidity range of 10% to 95%, non-condensation.
•Atmospheric pressure range of 50KPa to 106KPa.
Operational Environmental Conditions
•Unit must acclimate to room temperature in the environment it will be placed. 24 hours is recommended.
•Recommended environmental temperature range is 15°C to 32°C (60°F to 90°F).
•Recommended relative humidity is above 20%, non-condensation.
ENVIRONMENTAL CONDITIONS
All Pedigo Products, Inc. equipment is sold
F.O.B. shipping point, and when accepted
by the carrier, such shipments become the
property of the consignee.
Should damage occur in shipment, do not put the appliance
into service until the damage has been inspected by an
authorized service provider.
Should damage occur in shipment, it is a matter between
the carrier and the consignee. In such cases, the carrier
is assumed to be responsible for the safe delivery of the
merchandise, unless negligence can be established on the
part of the shipper.
1. Make an immediate inspection while the equipment is
still in the truck or immediately after it is moved to the
receiving area. Do not wait until after the material is
moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until
you have made a proper count and inspection of all
merchandise received.
3. Note all damage to packages directly on the carrier’s
delivery receipt.
4. Ensure the driver signs this receipt. If he refuses
to sign, make a notation of this refusal on the receipt.
5. If the driver refuses to allow inspection, write the
following on the delivery receipt: Driver refuses to allow
inspection of containers for visible damage.
6. Telephone the carrier’s of¿ce immediately upon ¿nding
damage, and request an inspection. Mail a written
con¿rmation of the time, date, and the person called.
7. Save any packages and packing material for further
inspection by the carrier.
8. Promptly ¿le a written claim with the carrier and attach
copies of all supporting paperwork.
We will continue our policy of assisting our customers in
collecting claims which have been properly ¿led and actively
pursued. We cannot, however, ¿le any damage claims for
you, assume the responsibility of any claims, or accept
deductions in payment for such claims.
TRANSPORTATION DAMAGE & CLAIMS
Environmental Conditions Delivery Transportation Damage and Claims

MM-1068 (MN-29617) • Rev 0 (10/15) • WarmWatch® Combination Blanket/Fluid Warmer • 2
•Carefully remove the appliance from the carton
or crate.
NOTICE: Do not discard the carton or other
packaging material until you have
inspected the unit for hidden damage
and tested it for proper operation.
•Read all instructions in this manual
carefully before initiating the installation
of this appliance, using the appliance or
performing routine maintenance. Following
procedures other than those indicated in
this guide to use and clean the appliance
is considered inappropriate and may cause
damage, injury or fatal accidents, in addition
to invalidating the guarantee and relieving
the manufacturer of all liability.
•DO NOT DISCARD THIS MANUAL.
This manual is considered to be part of
the appliance and is to be provided to the
owner or manager of the business or to the
person responsible for training operators.
Additional manuals are available from the
service department.
•Remove all protective plastic ¿lm, packaging
materials, and accessories from the appliance
before connecting electrical power. Store
any accessories in a convenient place for
future use.
UNPACKING AND SET-UP
Unpacking & Set-up

MM-1068 (MN-29617) • Rev 0 (10/15) • WarmWatch® Combination Blanket/Fluid Warmer • 3
1. The blanket chamber is intended for warming DRY, cotton
blankets ONLY. The fluid chamber is intended for warming
injection and/or irrigation fluids ONLY. No other use for
these devices is authorized or recommended.
2. This warmer is intended for use in commercial
establishments where all operators are familiar with the
purpose, limitations, and associated hazards of this device.
The warmer can be used wherever there is appropriate
space and electrical source including patient support areas,
ER, ICU, PAU, surgical suites, patient rooms, and nursing
stations. Operating instructions and warnings must be read
and understood by all operators and users.
3. Any troubleshooting guides, component views, and parts
lists included in this manual are for general reference only
and are intended for use by qualified technical personnel.
4. This manual should be considered a permanent part of this
device. This manual and all supplied instructions, diagrams,
schematics, parts lists, notices, and labels must remain with
the device if the item is sold or moved to another location.
Safety Procedures and Precautions
SAFETY PROCEDURES AND PRECAUTIONS
NOTICE: Used to notify personnel of installation,
operation, or maintenance information that is
important but not hazard related.
Used to indicate that referral to operating
instructions is a mandatory action. If not
followed the operator or patient could suffer
personal injury.
Used to indicate that referral to operating
instructions is recommended to understand
operation of equipment.
Knowledge of proper procedures is essential to the safe
operation of electrically energized equipment. The following
hazard signal words and symbols may be used throughout
this manual.
CAUTION
Used to indicate the presence of a hazard that can or
will cause minor personal injury, property damage, or a
potential unsafe practice if the warning included with this
symbol is ignored.
DANGER
Used to indicate the presence of a hazard that
WILL cause severe personal injury, death, or
substantial property damage if the warning
included with this symbol is ignored.
WARNING
Used to indicate the presence of a hazard that
CAN cause personal injury, possible death, or
major property damage if the warning included
with this symbol is ignored.
CAUTION
Used to indicate the presence of a hazard that
can or will cause minor or moderate personal
injury or property damage if the warning included
with this symbol is ignored.
NOTICE: For equipment delivered for use in
any location regulated by the
following directive:
DO NOT dispose of electrical or
electronic equipment with other
municipal waste.
WARNING
Transport shall only be done with the doors closed.
WARNING
Appliance and accessories may be
heavy. To prevent serious injury,
ALWAYS use a sufficient number
of trained and experienced workers
when moving or leveling appliance
and handling accessories.
NOTICE: Due to the energy efficient design of the
warming cabinet and tight seal around the
door, the water vapor from moist or damp
blankets placed in the warming cabinet may
cause condensation to collect on interior
surfaces. To avoid this accumulation, use DRY
blankets or towels.