Percussion Play Congas User manual

Ground Fixed
5. Once happy with location of
the Instrument, fill hole using
rapid hardening concrete. Be
sure to compact concrete
around legs and leave to dry
according to manufactures
guidelines.
2. Attach Ground Fixings to
legs(1.2) (See Ground Fix Post
Installation Sheet)
3.Excavate1 hole for the Steel
leg 250mm diameter by
400mm deep, in desired
location upon decision from
customer.
4. Locate (lower) legs into hole
making sure they are vertical
and level prior to concreting in
place.
1. Attach the steel leg to each
of the congas with the
M10x30 security screws,
square washers and HDPE
mounts. (1.1) (See Assembly
Guide)
400mm
Ground Surface
S,M,L
Small –600mm
Medium –700mm
Large- 800mm
Installation Instructions
(1.1)
(1.2) Instrument
Components:
M10x50 Security Screw
x4
M10x50x3 Square washer
x4
M10x200 Bolt
x2
M10 Nut
x4
Ground Fix
Components:
200 Mount
250 Mount
x2
x2
Install Instrument
with 1.5m free space
(from widest point)
around it.
1.5m
1.5m
Played with hands
Congas
Page 1 of 3
Weight of heaviest part 3.8kg (Large drum Small Congas)
Weight of heaviest part 4.5kg (Large drum Medium Congas)
Weight of heaviest part 5.2kg (Large drum Large Congas)
BS EN 1176
14.8 Kg
15 Kg
20 Kg
Metric Conversion:
250mm/ 10”
400mm/ 16”
600mm/ 24”
700mm/ 28”
800mm/ 31”
1.5m/ 59”
Spares available form
percussionplay.com or from your
local distributor

Ground Fixed
Instrument
Components:
Assembly Guide PPCONG
(1.1)
Ground Fix
Components:
M10x30 Security Screw
x4
M10x50x3 Square washer
x4
M10x200 Bolt
x2
M10 Nut
x4
200 Mount
250 Mount
x2
x2
Played with hands
Congas
Page 2 of 3
TX 45 Driver Bit
Tools:
x1
BS EN 1176
14.8 Kg
15 Kg
20 Kg
Thread Lock Solution
Required (Not Supplied)
Thread Lock Solution
Required (Not Supplied)
Thread Lock Solution
Required (Not Supplied)
PPCONG FRONT PPCONG SIDE
PPCONG PLAN
M10x50 Pin torx X4
M10x50x3 square washer X4
M10 Nut X4
M10x200 Threaded Bar X2
COMPONENTS LIST:
HDPE MOUNT 200 X2
HDPE MOUNT 250 X2
Spares available form
percussionplay.com or from your
local distributor

Ground Fixed
Components:
Ground Fix Post Installation
M10x200 Bolt
x2
M10 Nut
x4
Insert M10x 200 Threaded
bar into pre drilled holes
in Ground Fixing Post
Fix M10x 200 Threaded
bar in place using M10
Nuts
Fill hole with fast drying
concrete to manufacturers
specifications.
450
50
350
250
Aggregate
Concrete
Excavate a hole with a
250mm diameter tapering
down to 350mm diameter
and 450mm depth
Compact base of hole with
50mm of aggregate.
Lower ground Fix post
attached of instrument
into hole (check
instrument straight and
level before filling with
concrete)
(1.1)
1 2 3
4 5
400mm min depth
Congas
Page 3 of 3
BS EN 1176
Foundations should not present a hazard. These foundations are recommended as a guide,
for more information on foundation details for various surface see Part 7 of BS EN 1176.
Metric Conversion:
50mm/ 2”
250mm/ 10”
350mm/ 14”
400mm/ 16”
450mm/ 18”