Percussion Play TUTTI User manual

Ground Fixed
1555mm
Ground Surface
500mm
Installation Instructions
M10x200 Bolt
x3
M10 Nut
x6
Ground Fix
Components: 55 Kg
Install Instrument
with 1.5m free space
(from widest point)
around it.
1.5m
1.5m
Pair Small Red
Beaters X3
M10 Nut
M6x20 Security Screw
x18
M6 Saddle Strap
x9
Instrument
Components:
TUTTI
Page 1 of 3
Weight of heaviest part (TUTTI Frame)
BS EN 1176
Metric Conversion:
300mm/ 12”
500mm/ 1 ft 7 11/16”
1555mm/ 61”
1.5m/ 59”
CAUTION: TUTTI
surface can get hot
in direct sunlight, if
possible install in
shaded areas.
x2
x2
x2
x3
1. Unpack frame 7no.
2. Lay packaging out on floor
or assemble on non-abrasive
surface to prevent marking of
polished stainless steel.
3. Align holes on legs
(opposite end to polished
domes) and secure in place
using 3no. M10 x 200mm
threaded bar and 6no. M10
nuts provided. Colour Coded
Tools required 2no. 17mm
metric spanner/wrench (11/16
inch or alternatively using
adjustable wrench) (See
Assembly Guide Sheet)
4. Invert assembled frame so
domed ends face upwards.
5. Insert 6no. M8x60mm
Screws into pre drilled holes
in frame using TX40 bit.
5. Once happy with location
of the Instrument, fill hole
using rapid hardening
concrete. Be sure to compact
concrete around legs and
leave to dry according to
manufactures guidelines.
3.Excavate 1 hole for the
Steel leg 300mm diameter by
minimum 500mm deep, in
desired location upon
decision from customer.
8. Locate (lower) legs into
hole making sure they are
vertical and level prior to
concreting in place.
6. Attach 3No. Notes Panels to
Frame and beater to each arm.
(See Assembly Guide Sheet)
Can be
installed
deeper if
required
Spares available from
percussionplay.com or from your
local distributor
M8x60 Security Screw
x6

Ground Fixed
Components:
M10x200 Threaded Bar
x3
x6
(1.1)
TUTTI
Page 2 of 3
M10 BZP Nut
BS EN 1176
Thread Lock Solution
Required
Assembly Guide PPTUTTI
TX 40 Driver Bit
Tools:
x2
TX 30 Driver Bit
x1
Thread Lock Solution
Required not supplied
Attach each Note
Panel to the
corresponding
saddle straps on
the Frame with the
M6x20mm Screws
provided
Attach one Red
Beater to each of
the arms to finish
assembly.
M8x60 Security Screw
x6

300
550
400
Excavate a ho les with a
30 0mm dia me ter tapering
do wn to 400mm diameter
and 550mm depth
Compa ct b ase of hole with
50mm of aggrega te. Lower
gro und Fix po st a ttache d to
instrume nt into hole (check
instrume nt stra ight and level
be fo re filling with concrete)
F ill h ole with fast
d ry ing co ncrete to
ma nufacturers
specifications.
500
50
If Harmony needs to
be positioned lower a
dee per hole can be
exca vated.
500
50
Ground Fixed
Components:
Ground Fix Post Installation
(1.1)
123
TUTTI
Page 3 of 3
BS EN 1176
Foundations should not present a hazard. These foundations are recommended as a
guide, for more information on foundation details for various surface see Part 7 of BS EN
1176.
Metric Conversion:
50mm/ 2”
300mm/ 12”
500mm/ 20”
550mm/ 22”
500mm min depth
M10x200 Threaded Bar
x3
x6
M10 BZP Nut