Pet Gear PG8800 User manual

To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
EXPEDITION PET STROLLER
PG8800
AT
Interior Dimensions:
32L x 25W x 23H

EXPEDITION PET STROLLER • PG8800
2
PARTS LIST
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
Axle and Brake Assembly
2-Back Wheels
2-Front Wheels
Stroller
Removable Internal Liner
Handle

EXPEDITION PET STROLLER • PG8800 3
WHEEL ASSEMBLY
Step 1. Slide back wheel on axle as shown in
Figure A.
Step 2. Push in axel until it clicks.
Step 3. Pull on wheel to make sure
the wheel is engaged.
Repeat on other side.
When nished it should look like Figure B.
A.
B.
Step 4. Position stroller frame as shown in
Figure C.
Step 5. Place front wheels on stroller by
clicking them into the 6" posts on the bottom
of the stroller shown in Figure C.
Pull up to make sure wheels are locked.
Step 6. Take rear wheels (on axel with brakes)
and lock them into the 2" posts by placing leg
tube over the posts and pressing down until
they click (shown in Figure C).
Pull up to make sure wheels are locked.
C.
To remove
axel press on
velco button.
To remove front wheels,
press both release tabs.
Inside Outside
Lock/Release Button
Back Wheels
D.
To remove wheel, push
the lock/release button
(Figure D) and pull
wheel off.

EXPEDITION PET STROLLER • PG8800
4
STROLLER ASSEMBLY
Step 1. Place stroller so wheels are on the
ground and back wheels are facing you (shown in Figure D). D.
Step 2. Lift right and left side of stroller up (shown in Figure E).
Secure the support bar that goes from the left and latches down on the right side (shown in Figure F).
E.
F.

EXPEDITION PET STROLLER • PG8800 5
Step 2. To install the handle, place handle ends
into the handle-locking mechanisms on each
side of the stroller.
Then, push down until you hear a click and the
velco pins pop out on each side.
Choose height level (1 or 2), then release
velco pins.
Pull up on handle to make sure it is securely locked. This is shown in Figure G.
STROLLER ASSEMBLY
Velco Pin
Handle Locking Mechanism
G.
Velco Pins
TO USE FRONT WHEEL LOCKING MECHANISM
To engage front wheel-locking mechanism so that the front wheel does
not swivel, (best when stroller is used for fast walking or running), make
sure wheel is facing forward (so red tab is at the front of stroller) and
pull the red tab up.
To disengage locking mechanism so that the front wheel swivels, (for
easy steering), push tab down.
Lock
Unlock

EXPEDITION PET STROLLER • PG8800
6
Step 2. Pull support bar up to release and continue
to swing the bar counter-clockwise.
TO FOLD/PACK UP STROLLER
Step 1. Remove handlebar, by pushing velco pins in to
release.
Pull handlebar up and off.
Velco
Pin
Step 3. Fold sides inward, until at.

EXPEDITION PET STROLLER • PG8800 7
LOOKING AFTER YOUR STROLLER
WHEEL MAINTENANCE
• Always store product in a clean, dry place.
• Not recommended for use on the beach.
• Do not put heavy items on top of the stroller.
• Clean frame by wiping with a lightly oiled cloth.
• Do not use detergent or abrasives. Spot clean fabric with dry cleaning uid or mild
soap and warm water.
• To ensure easy maneuverability and to minimize wear and tear, (especially wheels,
axles, and swivels), keep all moving parts clean and lubricated with WD40® or
light machine oil.
• NOTE: Do not lubricate brake components or swivel locks.
• Regularly check stroller for loose parts. These should be tightened or replaced.
• To clean and lubricate front and rear wheels, push out locking lever under wheel
housing to release rear wheel.
• To ensure ease of maneuverability and to minimize wear and tear, keep all moving
parts clean
and lubricated with WD40® or light machine oil.
• Push wheel sets back on until they click and lock in position; pull on wheel housings
to ensure they are secure.
• Push stroller back and forth and rotate swivels around to work in lubricant.
• Clean the rear wheel assembly and the rest of the frame with warm, soapy water;
clean off with warm water and dry thoroughly.
• NOTE: Do not lubricate brake components or swivel locks.

EXPEDITION PET STROLLER • PG8800
8
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw
aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive,
destructive, immature or untrained animals. Do not use near an open or exposed ame. Failure to follow these
warnings and the instructions could result in serious injury or death.
• Do not carry additional bags, goods, or accessories in or on stroller except as recommended
in the manufacturer’s instructions.
• Recommended use of an approved safety restraint correctly tted and adjusted.
• Do not leave pet unsupervised in stroller.
• Before making adjustments to stroller ensure that pet’s body is clear of any moving parts.
• This stroller is designed for one pet only.
• Do not hang bags from handles as this may cause the product to become unstable.
• Do not use on escalator or stairs; fold stroller and carry.
• Put on brake whenever you park the stroller.
• Ensure stroller is completely erected and check that all locks are engaged before placing pet
in stroller.
• Do not overload as stroller may become unstable; maximum weight of pet using this stroller
not to exceed 150 lbs.
• Any goods carried in the basket not to exceed 6 lbs.
REPLACEMENT PARTS
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
192 Sheldon Avenue∙West Rutland, VT∙05777∙877-752-9123∙www.petgearinc.com