Petsafe SmartDoor MPA11-12019 User manual

PetSafe®
SmartDoor™Wall Entry
Conversion Kit - Small
Pet Door
Installation Guide
Please read this entire guide before beginning

2 1-800-732-2677
Thank you for choosing PetSafe®. Our mission is to ensure your pet’s safety by
providing you the tools and techniques to successfully train your pet. If you have any
questions, please contact the Customer Care Center at 1-800-732-2677 or visit our
website at www.petsafe.net.
To get the most protection out of your limited warranty, please register your product
within 90 days at www.petsafe.net. By registering, you will enjoy the product’s full
warranty and should you ever need to call the Customer Care Center, we will be
able to help you faster. Additionally, you will not have to save your product receipt as
registering serves as proof of purchase. Most importantly, PetSafe®will never give or
sell your valuable information to anyone.
_____________________________________________________________________________________
Table of Contents
Components ...............................................................................................3
Other ItemsYou Will Need...........................................................................3
Measure and Cut Wall Access ......................................................................4
Install Supports...........................................................................................6
Attach the SmartDoor™to the Wall Extension Frame A.................................7
Install the Assemblies into the Wall...............................................................7
Install Batteries and Begin Training..............................................................7
Product Warranty ........................................................................................8

www.petsafe.net 3
Components
Installation Guide
PetSafe®SmartDoorTM
Wall Entry
Conversion Kit
Wood screws
Phillips head
M4 x 40 mm
14 pcs.
Lock Washers
M4 4 pcs.
Te mplate
Machine screws
M4 x 10 mm
4 pcs.
Hex Nuts
M4 x 0.7 mm
4 pcs.
Inside
Frame (A)
Outside
Frame (B)
PetSafe
®
SmartDoor
™
Wall Entry
Conversion Kit - Small
Pet Door
Installation Guide
Manuel d’installation
Manual de instalación
Pleaseread this entire guide beforebeginning
Veuillez lire tout ce manuel avantde commencer
Porfavor,antes de comenzar, lea completamente estaguía
Washers
14 pcs.
Other Items You Will Need
• Stud Finder • PetSafe®Electronic SmartDoor™
• Framing Square Small (purchased separately)
• Level
• Phillips Screwdriver
• Drill with 5/16" and 1/2" bits
• Jig Saw
• Tape
• Pencil
• Lengths of 2" x 4" or 2" x 6"
• Decking screws
Important: Product intended for use in traditional framing and drywall
construction. For brick installation, outdoor cutout needs to accommodate the
wall entry frame to be recessed into the brick.
Always Remember
• Safety First
• Check Twice, Cut Once

4 1-800-732-2677
Measure and Cut Wall Access
1. Locate the site for your SmartDoor™Wall Entry
installation and verify accessibility for your pet
both inside and outside. Note: Check both indoors
and outdoors for electrical wiring or pipes in the wall
area in which you wish to install the Pet Door. If
necessary, cut a small hole in the wall to verify the
stud location and that no wiring or plumbing exists.
2. Locate the edge of one stud in the proposed area
with a stud finder. Using a pencil, draw a 5"
vertical line on the edge of the stud about 10"to
12"above the floor (1A).
3. Mark the shoulder height of your pet on the
vertical line. Draw a horizontal line through
your mark (1B).
4. Cut Template to size (8
5
/
8
" x 15
5
/
8
") and Place
against the wall aligning the shoulder height line
on the template with shoulder height line on the
wall. Align the edge of the template to the 5”
vertical line. Make sure your template is placed
on the proper edge of the stud, not over the stud
(1C, 1D).
5. Carefully trace the template with a pencil (1E).
Remove the template from the wall.
6. Take a moment to review the hole location to
ensure that the template is level and that this is
the best possible location for the Pet Door.
10"-12"
Edge of stud
Shoulder Height
5" Vertical
Line
1A
1B
15
1
/
8
"
8
5
/
8
"
1C 1D 1E
Step
1

www.petsafe.net 5
7. Drill the 4 corners all the
way through the inside
and outer walls. Use a
5/16
"drill bit, and use the
framing square to be sure
you keep the drill level
and perpendicular to the
wall (1F).
8. Carefully cut the hole
out using a jigsaw or
other appropriate cutting
device (1G).
Note: Cut on line.
9. Using the Inside Frame
A, check the fit (1H). Do
not force if the fit is too
tight. If the hole is too
small, simply remove the
Inside Frame and re-cut
or file the hole slightly to
enlarge (1I). Do not cut
more than
1/8
"from your
previous cut.
10. Once the Inside Frame
properly goes into the
hole, adjust to ensure the
unit is square.
11. Move outdoors and
repeat the process. For
1H 1I
5/16"
1F 1G
fitting the Outside Frame B use the previously drilled holes as your corners. Always check that
your lines are plumb (vertical) and level (horizontal). Remember to measure frequently, so you
only need to cut once.