PEUGEOT Elyseo User manual

Owners manual
50cc / 100cc

1
Information
Information.................................................................. 2-3
Equipement.................................................................... 4
Instrumentpanel ............................................................ 5
Switch............................................................................ 6
Petrol / Oil ..................................................................... 7
Battery / Fuse................................................................ 8
Lighting/Signalling ........................................................ 9
Starting theengine....................................................... 10
Running / driving / Mission box / Spark plug .................11
Braking / parking.......................................................... 12
Tyres ........................................................................... 13
Removing / Refitting front / rear wheel ........................ 14
Integrated.................................................................... 15
Transponder ................................................................ 16
Specifications............................................................... 17

Information
You have just purchased a PEUGEOT scooter.
Thank you for the confidence that you have
shown in our company.
Thisguide describeshow tocontrol, useand perform
basic maintenance on your new PEUGEOT scoo-
ter. As with all high technology machinery, you will
find it easier to control and you will obtain the best
results from your SCOOTER if you use it and
maintain it with care and attention. Your dealer will
advise and inform you and use his experience to
strictlyrespect the maintenanceplan thisis essential
to keep your scooter in perfect working condition.
Your PEUGEOT dealer knows all your scooter’s
special features. He has PEUGEOT original parts
and special tools to perform standard maintenance
on your scooter under optimum conditions.
Safety recommendations
The safety of a scooter depends on the care taken
by its driver.
Excessive speed is a decisive factor in many acci-
dents.
Respect speed limits and never go faster than is
safe under the road conditions. Take care not to skid
on road marking lines. Always do a general check
before using your scooter to make sure that it can
be used safely. Traffic rules require that the driver
and his passenger wear a helmet. It is also
recommended that you wear gloves, an eye protec-
tion and bright and visible clothes to increase safety.
A new Scooter driver should become familiar with
his scooter before starting to drive in traffic. A scoo-
ter driver must signal his presence to other users
by: - Switching on his lights when in motion
- Avoiding driving in places in which he is not
visible to other vehicles
- Driving carefully
Please take
the time to
read it
carefully.
- Taking special care at intersections, car park
entrances and exits, and slip roads. Your scooter is
designed for town use on the road only. Optional
luggageand briefcasecarriers aredesigned totrans-
port lightweight objects. Make sure that the weight
is distributed evenly and that loads are securely
fastened.
- Maximum Loads : 3 kg
Your scooter is designed to satisfy legal
requirements,pleasedo notmake any modifications
to it particularly to the exhaust.
Use only petrol, oil and lubricants tested and
recommended by PEUGEOT .
Maintenance recommendation
In order to keep your scooter in a safe and reliable
ridingcondition, donotmodify itandonlyusegennine
PEUGEOT parts for maintenance and repair. Use
of other spare parts may detrimentel to your vehicle
If your scooter is involved in a crash, have the main
parts checked carefully, for example all parts making
up the frame,suspension and steering system. This
inspection will help to restore essential safety con-
ditions.
It is recommended that you make a general check
after storing your scooter for an extended period of
time .
To avoid injury, always make sure that the engine
is switched off and the scooter is stable on its
stand on a flat surface before performing any
maintenance operations.
Take your scooter to a Peugeot dealer to do any
repair work, checks, tune-ups, maintenance or to
obtain recommendations for use.
You have chosen a Peugeot scooter for its fine
technical qualities and for its attractive finish and
appearance.
The bodywork is made of plastic parts coated with
special paints making it easy to keep it looking as
good as new.
Cleaning consists of washing dirty parts with soapy
wateror with amild detergent,rinsing frequently with
clean water and drying with a chamois leather.
In general do not use high pressure cleaners or
solventssuchas petrolor highly alkalinedetergents.
You can always call a Peugeot dealer if in doubt. He
will advise you about how to use maintenance
products or to repair scratched or grazed parts.
2

Inspection before the vehicle
leaves
What the buyer has to do.
To Check
- The fuel level
- The oil level in the tank
- The possible leaks
- The state of the tyres and their inflating
- The level of the brake fluid *
To check the smooth
working of
- The front and the back brakes
- The accelerator
- The front and back lightings
- The stop light and the indicators
- The horn
* According to the model
3
Protection of the environment
Fuel / Lubricant
- Use only unleaded fuel.
- Avoid to run out of fuel while driving.
- Use only the recommended lubricants
- Don´t use any additives for fuel or lubricants
Ignition
- In case of misfiring or loss of power, slow
down and cut off the engine as described.
Contact your local dealer when the problems
persists
Cutting off the engine
- Switch off ignition only when the engine runs
at idle speed.
Starting the engine
- In case of problems when starting the
engine, contact your dealer to have it checked.
Using your vehicle
- Avoid driving or stationing your vehicle on
flammable underground (e.g. dry leaves).

4
Equipement
- Battery housing
- Stand handle
- Saddle lock
- Rear brake : drum brake
- Kick pedal
- Stand lever
- Central stand with lever
- Side stand *
- Front disk brake
- hand glove box
- Right glove box
- Towing hook *
- Enginenumber
- Framenumber
- Front brake lever
- Throttle
- Front brake fluid level
- Rear brake lever
- Bag hook *
- Ignitionkey
* According to the model
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
B
A
HG
D
E
F
J K
M
L
N
O R
I
T
S
C
Q
P

5
Instrument panel
- Headlight indicator light
- Oil warning light
Alert
If the oil alert indicator remains on while you are driving, you
must top up with oil quickly.
- Indicator light
- Antit theft warning light *
- Fuel level meter
Once the pointer has reached point , autonomy is about
20km.
- Speedometer
The needle shows the vehicle speed in km/h or mph.
- Digital clock
Battery-fed, the clock constantly displays hours and
minutes : the colon flashes on and off.
The month and the day are displayed when is pressed
sets the hour, minutes, month and days function
- (A) am
- (P) pm
press to select the function required
- Fuel reserve warning
light *
- Odometer
Shows the total distance travelled in kilometers.
* According to the model
C
A
B
C
AB C
1
2
3
4
5
6
7
8
9
431 2
5 9 7
6
8

Ignition keys and
locks
Two keys are supplied with the scooter
and are identified by a number. Please
keep them apart and note the reference
number. The ignition key :
- Makes the contact when starting
- Locks the steering
- Unlocks the saddle
- Starter switch
- Engine stopped
- Electrical contact position. Starter
and signal functions may be used.
- Steering locked
- Starter button
Start as described on page 10.
- Light switch
- Lighting off
- Lighting front sidelight,
speedometer and rear light, number
plate*.
- Lighting beadlights or dipped
beadlights according to the position of
the reverser high beam/low beam ,
speedometerandrearlightnumber plate*
- Reverser high
beam/low beam
- Turn signal light
switch
To signal a change of direction :
- To the right, push the switch to
- To the left, push the switch to
The indicator is turned off by pressing
the central button.
- Horn button
* According to the model
E
D
F
C
B
A
G
H
6
1
2
3
4
5
6
4
D
E
F
B
C
A
HG
23
4
6
1
5

Saddle
To open :
- Insert the ignition key in the lock at the back of the left side, rotate it
a quarter of a turn towards the right and lift the saddle.
To close :
Press the back of the saddle
The seat storage compartment gives access to :
- Helmet housing,
- Petrol tank,
- Oil filling orifice.
Do not store aerosols in the seat storage compartment.
- Petrol
For best operation of your engine, use only non-leaded petrol 98
or 95 for vehicles with a catalytic converter and leaded petrol or
98 - 95 for the others.
Do not allow water or any grit or particles to enter the tank when
filling.
Do not use an oil and petrol fuel mixture.
Warning
Petrol is an extremely inflammable substance that can explode
under some conditions. Fill up with petrol in a well ventilated
location with the engine switched off. Do not smoke, do not
allow flames or sparks close to the scooter or close to the place
in which the petrol is stored.
Do not overfill your tank. Petrol must not reach the neck of the
filling orifice. Make sure that the plug is well closed after filling.
Petrol is a dangerous substance and can be fatal if swallowed.
Avoid repeated and prolonged contact with the skin and do not
inhale the vapors. Keep out of reach of children. Do not cause
vomiting if petrol is swallowed. Call a doctor immediately.
- Oil level
Check the oil level regularly.
For good engine lubrication, use :
- Semi-synthetic oil or synthetic for a 2-stroke engine with
separate lubrication
Important
Top up with a recommended oil.
Use of other types of oil may cause an excessive build up of
carbon in the engine and in the exhaust system, resulting in loss
of power and damage to the engine.
Do not overfill your tank. Oil must not reach the neck of the filling
orifice. Make sure that the plug is well closed after filling.
If your oil tank has been completely emptied, this may cause
damage to the engine when you start it; please take your scoo-
ter to a PEUGEOT dealer so that he can carry out the essential
operation of purging the lubrication circuit
2-T SPECIAL (semi synthetic)
2-TSYNTHETIC
recommends
ABC
7
C
B
CA
B

Battery and fuse
- Battery
Battery electrolyte.
Check and keep the level between the «upper» (maximum) and
«lower» (minimum) marks.
Only top up using demineralized water or special lead battery
water.
When you replace the battery, make sure that the air vent hose is
properly in place and is not blocked or pinched.
Charging the battery
The level of battery liquid must always be checked before
charging.
The charge must be carried out with a suitable battery charger
with a maximum output of 0.4 to 1 ampere ; we recommend that
this operation is done by a dealer.
Note : you can damage the battery if the battery charger that
you use is too powerful.
Caution
The battery contains sulfuric acid. Do not allow the electrolyte
to come into contact with your skin, eyes or clothes.
Antidote: external : rinse with water.
Internal : do not drink or provoke vomiting.
Immediately call a doctor or the nearest anti-poison center.
Eyes : rinse with water and immediately call first
aid.
The battery releases explosive gases.
Do not bring sparks, flames or cigarettes close.
When charging or using in a closed location, make sure that the
ventilation is good.
Protect eyes when working close to a battery.
Keep the battery out of reach of children.
Precaution
When checking the battery electrolyte level or adding distilled
water, make sure that the air vent pipe is properly connected to
the battery.
Use demineralized water or special lead battery water only for
your battery; tap water will reduce its life. Please call a PEU-
GEOT dealer if you have excessive electrolyte loss.
Connections to battery wires :
- Connect the red wire to the battery's (+) terminal,
- Connect the green wire to the battery's (-) terminal.
- Fuse
A fuse protects the electrical equipment against short circuits or cir-
cuit overloads.
It is located in a fuse holder at the side of the battery.
It melts and breaks the circuit if there is a fault in the installation.
Precaution
The fuse only burns out if there is a fault in the electrical circuit.
Please call a PEUGEOT dealer.
Only use standard fuses.
Replace a burnt out fuse by a fuse of the same capacity.
1
2
8
12

9
Lighting and signalling
Lightingandsignallingequipmentingoodworkingcondition
is essential for safety.
Check the various lamps from time to time before starting
and when using your scooter to make sure that they are
working as they should.
- Lamp characteristics
Headlight/Diplight ....................S2 35/35W BA20d
Rear light and brake light ......... P2 21/5W BAY15d
Turn signal lights .............................R10W BA15S
Speedometerlighting ........... W1,2W T5 (no base)
and arning lights .................. W1,2W T5 (no base)
Number plate light *...............................W5W(T10)
Side lights * ...........................................W5W(T10)
All lamps are 12 volts
See your dealer or distributor immediately if one of the
lamps is not working properly.
- Changing bulbs
Front :
- Take the 4 screws out of the front panel
- Pivot the fittings over
- Change the bulb
To adjust the headlight : unclip the box at the bottom of
the left hand glove and adjust the screw to vary the
vertical angle.
At the back :
- Remove the two screws and the lens
- Change the bulb
Indicators :
- Remove the screw and the lens
- Change the bulb
* According to the model
C
D
D
A
D
C
A
B
B

Starting the engine
- With the electric starter
For safety reasons :
- Put the scooter on its central stand.
The electric starter will not work unless you squeeze the left brake
lever.
To start the engine :
- Turn the ignition key to the position
- Squeeze the brake lever
- Press the starter button
- Release the button when the engine starts
When the engine is cold, keep the throttle closed.
Precautions
Never run the engine in a closed room. Exhaust gases contain
carbon monoxide and toxic gases.
- Kick start
- Put vehicle on its central stand
- Turn the ignition key to the position
- Kick the lever all the way through with a fast and continuous
movement
When the engine is cold, keep the throttle closed.
Precautions
- Do not allow the lever to kick back freely against its limit
stop
If the engine does not start after several attempts with the kick
starter or after three or four attempts with the electric starter,
open the throttle slightly and push the kick start quickly and
continuously.
To warm up gradually, let the engine run for a few minutes with
the throttle closed keeping the rear brake on.
Stopping the engine and
parking
Afterstoppingthescooter:
- Only turn off the ignition when the engine is at idling speed
- Put the ignition key to
- Put the vehicle on its stand
- Remove the key to prevent risks of theft.
- Parking on the stand
The stand is fitted with a lever to park the scooter easily.
- Move to the left side of the scooter
- Hold the scooter by its handlebar and the grab handle at the
back of the saddle
- Push the stand lever with your right foot while pulling the
scooter backwards with the handlebars and the saddle's grab
handle.
Caution
Make sure that the vehicle is stable on its stand so that it cannot
fall over and possibly cause any body wound or any damage to
the scooter.
- Placing on side stand *
Bearing in mind that the isde stand is equipped with an automatic lift
mechanism, be careful when carrying out different operations on the
vehicle.
Caution
Make sure that the vehicle is stable on its stand so that it cannot
fall over and possibly cause any body wound or any damage to
the scooter.
* According to the model
10
A
B
A
A
*
A
B

Running in and driving
- Running
Runninginhasanessential influenceon correctoperation, power
and long life of your engine. During the first 500 kilometers,
never run your scooter at maximum speed, particularly when
cold or going down hill.
- Driving your scooter
With the engine running on its stand :
- Keep the rear (left) brake lever on to lock the rear
wheel
- Do not open the throttle
- Lift the stand
- Get onto your scooter
- Free the rear wheel (release the brake lever)
- Accelerate to start (turn the throttle gradually)
- Turn the throttle in the opposite direction to decelerate.
Caution
You must lock the rear wheel before you lift the stand.
If the rear wheel is turning you could lose control of the scoo-
ter when it touches the ground.
-Do notaccelerate roughly(quickly openingand closing
the throttle)
- Do not leave your scooter unattended with the engine
running.
11
B
A
Maintenance and adjustments
(Frequency : see maintenance booklet)
- Mission box
Changing the gearbox oil is not absolutely necessary.
In case gearbox oil lack, have it topped up or renewed by
your local dealer.
- Spark plug
It is advisable to respect strictly the assembly
recommendations given by PEUGEOT.
The adaptation of a non recommended plug can destroy
the engine.
- Manually tighten the spark plug and washer,
- Using a spark plug wrench, tighten by 1/4 turn for a
new spark plug, and between 1/8 to 1/4 turn if reused.
- NGK BR7HS - EYQUEM R850
- NGK BR8ES - EYQUEM R1000L
100cc
50cc
B
A

12
Hydraulically controlled
front disk brake
The hydraulic circuit is filled with fluid in compliance with the
DOT3orDOT4standard. PEUGEOTusesLOCKHEEDD55.
- The fluid level in the hydraulic control,
- The circuit seal,
- The state of the brake pads,
control the braking efficiency.
If the brake control appears to be «spongy» when the brake
isactuated,takeyour scooter toyourdealerformaintenance
PEUGEOT.
- Brakes
Adjusting the rear brake
The brake clearance is the distance that the lever can move
before starting to actuate the brake.
Adjusting the clearance
Clearance : 10 to 20 mm measured at the end of the lever.
- Adjustment nut
- To increase clearance loosen
- To reduce clearance tighten
Brake wear sector
- Reference mark
- Arrow
If the arrow faces the mark when the brake is actuated fully,
the brake blocks must be replaced.
For your SAFETY, PEUGEOT recommends that you:
-Monitoroperationofyour FRONTand REARbrakes.
- Have adjustment and maintenance operations
performed by a PEUGEOT dealer whenever action
proves to be necessary
- Use PEUGEOT original parts only.
- Braking and parking
GoodcoordinationbetweenthethrottleandtheFRONTand
REAR brakes is very important.
- Reduce your speed by allowing the throttle to return.
- Pull on the rear and front brakes.
Caution
Braking is less efficient if you only use one brake.
Excessive braking may lock a wheel and make you lose
control of your scooter!
Whengoingdown asteep hill,turnthe throttlecompletely
down and use both brakes to reduce your speed and
maintain control of your scooter.
Do not use the brakes continuously, overheating will
reduce braking efficiency.
23
AB
1
A
B
3
1
2
20 mm

13
Tyre inflation pressure
Check the tyre pressure frequently and adjust it if necessary.
Observe the following specifications :
Nota : 1,5 bar = 0,15 Mégapascal
1,8 bar = 0,18 Mégapascal
Incorrecttyrepressure willcauseabnormal wearof thetyretread
and will reduce riding safety.
It is dangerous to drive with worn tyres (it is illegal to use worn
tyres, and they affect the steering-ability, braking efficiency, trac-
tion and road holding).
- Wheels
This scooter is fitted with tubeless tyres. Tubeless is marked on
thetyres'sivewall and on therimsto showthatthey are specially
designed for use without an inner tube.
Appropriate valves are fitted in rims.
When replacing them, use tyres and rims marked tubeless only.
Ask your PEUGEOT dealer to repair or replace your Tubeless
tyres.
Danger
Do not fit an inner tube inside a Tubeless tyre or put a
Tubeless tyre on an ordinary rim (risk of bursting).
TYRE Pressure cold
Front
Rear
120/70 x 12
120/70 x 12
1,5 bar
1,5 bar
TYRE Pressure cold
Front
Rear
120/70 x 12
130/70 x 12
1,5 bar
1,8 bar
50cc
100cc

14
Removing and refitting of the
front wheel *
Important
For these operations we advise you to contact a
garage equipped with special tooling or a Peugeot
dealer (agent).
- When dismantling, be careful not to damage the
pipework, brake disc, brake pads and brake shoes.
- Check the location of the parts, washers and
exhaust seal in order to put them back in the right place.
- Do not action the front brake lever once the wheel
has been removed as the calliper pistons may cause a
leakage of brake fluid. In the event of this happening, see
a dealer who will carry out the operation.
- Removing
- Position the vehicle on the centre stand and place a
support under the vehicle, so that the front wheel is free
and that the vehicle can’t fall over.
- Loosen the two screws with the washer ,
- Remove the brake calliper cautiously ,
- Block the wheel spindle
- Loosen and remove the nut and the washer,
- Loosen the screw ,
- Push the wheel spindle using a rubber hammer
ifnecessary,
- Take off the front wheel and remove the wheel
spindle manually,
- Remove the wheel.
- Refitting
- Place the reduction gear on the wheel,
- Present the wheel between the fork tubes and place
the reduction gear on the tube ,
- Introduce the wheel spindle ,
- Put the washer in place and screw the nut whilst
blocking the spindle to a tightening torque of 5 m.daN,
- Fix the brake calliper by tightening the two screws
and the washer to a tightening torque of 2,7 at 3,2 m.daN,
- Tighten the screw to 1,2 m.daN.
Removing and refitting of the
rear wheel
- Remove the rear-wheel hub protector
- Tighten the nut to a tightening torque of 12
m.daN.
* According to the model
3
2
1
46
7
8
A4
35
6
1
A
2
4
3
5
4
4
1
87
5
100cc

Anti-Theft Device *
- Removal of anti-theft device
-Putthekeyinto the lock,turnit ,andpullthe protective
flap in order to remove the anti-theft device.
- Locking the anti-theft device
(the key must be in the lock).
Unclip part from its housing, slide it along the cable,
wrap the cable around a fixed point (metal post, 2-wheeler
parking stand, ....)
- Turn the key and insert part into part ,
- Turn the key , remove it and make sure that
the protection flap is correctly in position.
- Storing the anti-theft device
- Put the key into the lock, turn it and separate parts
and .
- Slide part along the cable and store it away in the
housing of part .
- Push the whole unit until it is positioned in the rear part of
thescooter.
- Withdraw the key and make sure that the protection flap
is closed correctly.
Advice
- When the scooter is parked, avoid leaving the anti-theft
device in contact with the ground.
- When cleaning the scooter, avoid pointing the water hose
into the lock.
- Maintenance of the tube : use a plastic siliconed cleaning
product.
Caution
Do not forget to store the anti-theft device carefully in its
housing before using the vehicle.
Placing the theft protection device around the rear wheel
may damage the number plate.
Recommendations for
protection against theft
Use an additional good quality theftproof device.
A treated steel hook rigidly attached to the frame can
be used with a locking device to anchor your scooter to a
fixed point (for example a post).
* According to the model
15
1
12
3
1
2
1
2
3
1
2
1
3
L*
L*

Transponder *
The ignition keys (1 red and 1 black) are equipped
with a TRANSPONDER which is an electronic
component built into the key’s plastic part.
This anti-theft system allows the rider to start his
scooter thanks to an «ANTENNA» which surrounds
the key and recognises the transponder
ELECTRONICALLY.
All the elements required for starting the engine are
conditioned by the recognition of an ELECTRONIC
CODE generatedby thered key,calledtheMASTER
KEY, which means the scooter can not be used
simply by changing the ignition key.
Allthe so-calledsafety-relateditems arenot available
in After-Sales. However, if the rider can prove that
he is the owner of the vehicle, our Peugeot dealer
can order all the items of this system.
A LED warning light blinks on the instrument panel
to show that the system is actuated (dissua-
sive effect).
To save the battery, this LED stops blinking after 48
hours, although the system is still operational.
Important
We advise you not to use the Master
Key (red key) for everyday use but to
keep it in a safe place with the
number of the keys.
* According to the model
16
4

17
50 cm3100 cm3
Specifications
Dimensions(mm)
Overalllength ..........................................................................1900
Overallwidth (excluding rearviewmirrors) ................................ 720
Overallheight(including rearview mirrors) ...........1230 ............................... 1290
Wheelbase..........................................................1360 ............................... 1368
Weight (kg)
Tanksfull (versionaircooled) ....................................... 99 ..................................113
Capacities (L)
Oil tank ......................................................................................1,3
Petrol tank .................................................................................8,5
Mission box .............................................................................0,12
Engine block
Bore x stroke ................................................... 40x39,1........................... 50,6x49,7
Compressionratio .............................................. 9,8 to 1 ............................ 11 to 1
Displacement(cm3)................................................49,1 ................................. 100
Transmission
Primarygear ........................................................................... Trapezoidalbelt
Finalgear .......................................................... Reduction gear withtwogear trains
Electricity
Battery............................................................. 12V-4Ah ..........................12V-8Ah
Generator ...................................................................... Flywheelmagneto
Fuses ....................................................................................... 5A
Avoid:
- Noise, electrical interference, smoke, ....
Consequently, do not modify your vehicle (for example the original exhaust system).
Any modification of the technical specifications of the vehicle will result in the invalidation of
the guarantee and non compliance with the approval certificate (official approval of the
vehicle by the authorities); consequently you will no longer be covered by your insurance in
the event of an accident.
And do not forget that a PEUGEOT scooter should be maintained at a PEUGEOT dealer.
Only your dealer knows it thoroughly, and has genuine PEUGEOT spare parts and the
required special tools PEUGEOT to perform complete service and maintenace operations.
Like us, he is at your service.

Dans un souci constant d’amélioration Peugeot Motocycles se réserve le droit de modifier, supprimer ou ajouter toute référence citée
DC/PS/DOC/SH Imp. en U.E. I3R 17/01/2000 ed3 (photos non contractuelles)
recommends
N° 11.742363.00
E
N
G
L
I
S
H