Philips AWP1808 User manual

AWP1808
Water solutions
Hướng dẫn sử dụng
User manual 1~12
13~24

Product introduction
1 1
2 1
Product overview
3 2
7
10
11
Installation
Preparation before installation
4 3
3
3
Usage instruction
First time usage
Recommended replacement period
5
Precautions 6
7
Trouble shooting
8 Guarantee & Service
5
5
6
6
129 Packing list
Content

1. Product introduction
2. Main technical specications
Thank you for purchasing. This is a water softening
pre-lter. With ion exchange resin, it can eectively
reduce Ca2+ and Mg2+, reducing hardness of water
to protect the under-the-sink ltration system.
QuickTwist technology allows easy lter replacement.
Filter can be removed with a simple twist.
1
Model AWP1808
600 L
3L/min
0.1 – 0.4 MPa
Municipal tap water
Total rated water
purication amount
Puried water ow
Inlet water pressure
Applicable water source
Filter cartridge AWP401

2
3. Product overview
1
3
2
1Filter base
2Hanging board
3Filter cartridge
304.8mm
67.6mm 85mm

4. Installation
Preparation before installation
(1) Prepare tools for installation: percussion drill,
cross screwdriver, monkey wrench, pipe scissors.
(2) Check if the accessories in packaging list are all
provided.
Installation of the lter
Choose whether to use plastic pipe for bolt
installation according to the actual condition of
the installation surface.
Pre-lter
1
3
Hot Cold

Place the hanging board on the
wall surface horizontally, go
through the xed holes on the rack
with three bolts to x the rack on
the wall;
2
Rotate the lter clockwise into
the lter seat;
3
Insert the L-shaped joints into
the water inlet and water outlet
on the lter seat;
4
Hanging
board
Plastic
pipe
Wall-hung
screw
1
2
4

5. Usage instruction
First time usage
(1) Open the three-way valve.
Keep the water owing out from
water outlet of lter for 5-10
minutes;
(2) Close the three-way valve.
Connect the PE pipe on lter
water outlet with water purier;
Cut the 3/8” PE pipe into
appropriate length, insert one end
into the water inlet on pre-lter,
and the other end into the
three-way ball valve;
Cut the 3/8” PE pipe into appropriate length. Insert it
into the water outlet on pre-lter;
5
冷热
Open
冷热
Close
5

(3) Open the three-way valve. Water purier can be
used now.
Replacement of lter cartridge
· Please replace the lter cartridge regularly as
recommended. New lter cartridge can be obtained
from Philips agents.
· The actual service life of lter cartridge depends on
local water quality and daily usage.
Recommended replacement period:
Model code
AWP401
Recommended
replacement period
About 2-4 months
Close the three-way valve;
Steps for lter cartridge replacement:
1
It can only be replaced with the original Philips
lter cartridge.
Close
6

6. Precautions
Please read this manual carefully before using the
product and keep it properly.
· The product installation, debugging or maintenance
must be implemented by the personnel authorized
by the manufacturer, to make sure the product is
under normal working state. If the product fails to
reach the normal state or property due to the
installation, debugging or maintenance without the
personnel authorized by the manufacturer, the
manufacturer shall not take the responsibility.
Unscrew the old lter cartridge
anticlockwise;
2
Screw the new lter cartridge
into the lter base clockwise.
3
1
2
1
2
7

· The components approved by our company shall be
used for product maintenance and lter exchange,
the problems caused due to use of unauthorized
components or accessories, the declined operational
performance or the resulted property damage shall
not be included within the limited guarantee scope
of the manufacturer.
· Non-original lter may have problems such as lack
of sanitary safety assurance in raw materials, declined
ltering performance and seal compatibility etc., and
it may result in abnormal water quality, bring safety
risk and impact the product service life.
· The product is applicable to household water use,
for example, if it is used for business, it will reduce
the service life of the product.
· The product shall be strictly forbidden to be installed
outdoors.
· After the product is installed and used, the user shall
make frequent examination and necessary
maintenance frequently according to the service
condition, in case of abnormality, the user shall stop
using immediately and call the service hotline of our
company for maintenance.
· The professionals not approved by our company shall
not adjust and repair the product.
· The right of interpretation for the above clauses
belongs to our company under the law.
· The product shall use the municipal tap water. Do not
use unknown water source
8

· The product shall not be installed on the water supply
line with the water pressure over 0.4 MPa. if the inow
water pressure is over 0.4 MPa, the reducing valve
must be installed (it needs to be purchased separately).
· The inow water temperature of the product shall be
5-38 degree Celsius, if the inow water temperature
is over 38 degree Celsius, it will damage the lter and
make it lose ecacy. If the inow water temperature
is below 5 degree Celsius, it might cause freezing,
and water leaking due to product components
breakage.
· For the product not used for a long term, the water
source must be disconnected so as not to damage
the product.
· Please do not place the product in the place under
high temperature and humidity
· The product shall not be installed in the places with
direct sunlight or exposed in the places containing
harmful chemicals, or any place that might suer
damage such as falling, impact etc.
· The product shall be cleaned with clean water, please
do not clean the product by direct watering, and do
not use steel wool, abrasive cleanser or corrosive
liquid (such as gasoline or acetone) to clean the
product.
· Please do not pour other liquid into the lter during
cleaning, so as not to cause damage to the lter
ltering system.
9

7. Trouble shooting
Error
The water
apparently
ows slow.
1. Cold water valve
or three-way valve
is not open completely.
2. The lter cartridge
is blocked.
3. The water pressure
is too low.
1. Open the valves.
2. Replace the
lter cartridge.
3. Contact after
sales personnel
for support.
The water is
hard. Filter lifetime ends. Replace the lter cartridge.
The ltered
water quality
is low.
1. Filter is not used
for over 3 days.
2. The tap water
quality is not good.
1. Flush the lter
for 5-10 minutes.
2. Use good quality
municipal tap water.
Water leakage
1. Pipes or lter are
not properly installed.
2. Accessories are
damaged.
1. Please install
properly
2. Contact after
sales personnel.
Causes Solutions
10

11
8 Guarantee & Service
This product includes a two-year warranty from the
date of purchase. If you need more information,
please visit: www.philips.com/welcome.
Within two years from the date of purchase, you will
receive free warranty service for any damage caused
by the manufacturing process or components under
normal operation conrmed by our maintenance
service.
The warranty service does not include frequent
replaced consumable components (water puried
lter, pitcher lter, granular activated carbon, ion
exchange resin, hollow ber membrane, etc.), auxiliary
devices, transportation fee and door-to-door service.
Please show the proof of purchase to the service
personnel during maintenance.
You cannot receive free warranty service under the
following conditions:
1. Damage by improper operation, such as improper
components connection, improper installation,
deprived of manual use, mis-operation.
2. Negligence and damage because of transportation
or other accident.

Please keep this user manual for future reference.
9. Packing list
Ion exchange resin lter
L shape connecter
2-division clip
3-division clip
Plastic pipe
User manual 1x
3x
3x
2x
2x
2x
1x
Screw
3. Maintenance and modication without approval.
4. Other damage caused by force majeure
(such as natural disaster, abnormal voltage, etc.).
5. Damage caused by general use outside home
(e.g. industrial and commercial use).
6. Aging, wearing and tearing caused by normal
operation of the product without aecting normal
operation of the product.
This statement serves as a publicity for free
maintenance within the specic time limit and conditions,
and does not limit the legal rights of consumers.
12

Giới thiệu sản phẩm
1 13
Thông số kỹ thuật chính
2 13
Tổng quan về sản phẩm
3 14
19
22
23
Cài đặt
Chuẩn bị trước khi cài đặt
Lắp đặt bộ lọc
4 15
15
15
Hướng dẫn sử dụng
Lần đầu sử dụng
Thay hộp mực lõi lọc
Thời gian thay thế đề xuất
5
Đề phòng
6
7
Xử lý sự cố
8
Danh sách đóng gói
17
17
18
18
249 Danh sách đóng gói
Nội dung

1. Giới thiệu sản phẩm
2. Thông số kỹ thuật chính
Cảm ơn bạn đã mua hàng. Cảm ơn bạn đã mua hàng.
Đây là một bộ tiền lọc làm mềm nước. Với nhựa trao đổi
ion, nó có thể loại bỏ Ca2 + và Mg2 + một cách hiệu quả,
giảm độ cứng của nước để bảo vệ hệ thống lọc dưới bồn
rửa. Công nghệ QuickTwist cho phép thay thế bộ lọc dễ
dàng. Bộ lọc có thể được loại bỏ với một twist đơn giản.
Mô hình AWP1808
600 L
3L/min
0.1 – 0.4 MPa
Nước máy thành phố
Tổng lượng nước lọc
định mức
Lưu lượng nước sạch
Áp lực nước đầu vào
Nguồn nước áp dụng
13
Lõi lọc AWP401

3. Tổng quan về sản phẩm
1
3
2
1Base Đế lọc
2Băng treo cartridge
3hộp lọc
304.8mm
67.6mm 85mm
14

4. Cài đặt
Chuẩn bị trước khi cài đặt
(1) Chuẩn bị dụng cụ để cài đặt: máy khoan gõ, tuốc nơ
vít chéo, cờ lê khỉ, kéo ống.
(2) Kiểm tra xem các phụ kiện trong danh sách đóng gói
có được cung cấp không.
Lắp đặt bộ lọc
Chọn sử dụng ống nhựa để lắp đặt bu lông theo điều
kiện thực tế của bề mặt lắp đặt.
tiền lọc
1
15
nóng
bức
lạnh

Đặt bảng treo trên bề mặt tường
theo chiều ngang, đi qua các lỗ cố
định trên giá bằng ba bu lông để
cố định giá trên tường;
2
Xoay bộ lọc theo chiều kim đồng
hồ vào ghế bộ lọc;
3
Chèn các khớp hình chữ L vào đầu
vào nước và cửa xả nước trên ghế
lọc;
4
Bảng treoƠng nhựaVít treo
tưòng
1
2
16

5. Hướng dẫn sử dụng
Lần đầu sử dụng
(1) Mở van ba chiều. Giữ nước chảy
ra từ cửa xả nước của bộ lọc trong
5-10 phút
(2) Đóng van ba chiều. Kết nối ống
PE trên cửa xả nước lọc bằng máy
lọc nước;
Cắt ống PE 3/8 có chiều dài phù
hợp, chèn một đầu vào đầu vào
nước trên bộ tiền lọc và đầu còn
lại vào van bi ba chiều;
Cắt ống PE 3/8 thành chiều dài thích hợp. Đưa nó vào ổ
cắm nước trên bộ tiền lọc;
5
冷热
Mở
冷热
Đóng
17