Phoenix PALLADIUM LS8000 Series User manual

PLD7000
/
9000BL
INSTRUCTION
LS8000 SERIES

2
Data media such as CDs or Diskettes are to be stored in data safes.
High value items such as cash or jewelries must be stored in certified
security safes.
Followings are the safety instructions & rules. Prior to using the safe,
please read the instructions carefully.
Cautions when placing the safe.
To avoid dampness, place the safe on a well ventilated and flat floor.
The safe is so heavy that it is to be handled very carefully.
Never move the safe in door open.
Be cautious not to be bumped against corners of safe.
Cautions when using the safe.
Be careful not to close the door roughly.
As a safe is heavy and operated with a smart digital lock, we
recommend children not to touch it.
The articles must be apart from door inside panel.
Overload articles may cause some troubles when closing and opening.
Be careful not to forget the user code, and keep the instruction
outside of the safe.
Be careful not to hurt hands or fingers when closing door.
Heavy articles are recommended to be laid on the bottom.
This fire safe is for storing paper documents, not for data media.
In case of high dampness inside the safe, the articles may go moldy
so that the desiccant must be replaced periodically.
FOR SAFETY

3
Components
Instruction 1.5V Alkaline
AA Batteries
8pcs
PLD7000BL : 2pcs / 8pcs
PLD9000BL : 3pcs / 12pcs
9V Battery
for Alarm
(Optional)
Shelf Shelf Clips
Alarm
(Optional)
Nomenclature
Overview
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
Push right side of door frame
to expose battery case.
SA
InteriorFront
Touch Panel
Door back
Battery Case
Touch Pad
FND
Battery
AS Alert
When AS Icon appears,
please contact to AS Center.
Finger-print
sensor
Battery Case
Memory
Button
Optional
Alarm
LED Light
Push

4
2) Pull out Battery Case
forward.
1 ) Push the front of
the battery case.
Prior to using safe,
1) Push the front of the battery case to expose battery case.
2) Load batteries.
3) Replace eight batteries
at same time.
1.
Batteries
*
When Battery Change Icon or Battery Change Message LobAtt appears, the locking system
* NOTE : If a wrong code entered, “bi-ric” sound and ErrOr on FND.
* Paralysis : If wrong codes entered 5 times, the lock gets paralyzed 5 minutes.
1) No response against pad touch.
2)
Paralysis Rest Time is indicated on FND as Min-Sec.
In case of paralysis rest time 4 minutes and 29 seconds, 4_29 indicated on FND.
3) After 5 minutes, paralysis gets released.
* Scramble Numbers :
When opening a safe, scramble numbers can be put
before and/or after the real code to avoid peeps. User code should be
touched consecutively.
32 numbers are acceptable including the real code.
(Ex) In case of user code ‘ 1 2 3 4 ’, touch ‘ xxx1234 ’, ‘ 1234xxx ’ or ‘ xxx1234xxx ’.
1) Touch Pad 2) Touch User Code 3) Touch
# 4) Open the door
(Factory Code 1 2 3 4)(OPEnd on FND)
2. Open with Code
may not work normally. A set of 8 alkaline batteries should be replaced together with the new one.
*
Even though batteries completely exhausted, the registered codes are not erased.
#
Touch Pad
PUSH PULL Replace Batteries
User Code Open the Door

5
* 32 finger-prints are acceptable.
* NOTE : 1) Prior to closing the door, please confirm with 5. Open with Finger-print if the finger-print
correctly registered.
2) Worn-out finger-print can’t be entered.
* NOTE : 1) Prior to closing the door, please confirm with 2. Open with Code
if the New Code registered correctly.
2) It is not recommended to enter the specific user code such as telephone number,
birthday, consecutive number, and etc. for security reasons.
2) Enter New Code
(4 ~16 digits)
3. Set User Code
Keep door open.
Keep door open.
1) Press M Button on door back.
4. Register Finger-prints
Please put user’s finger
on sensor while
blue lamp flickering,
3) Touch #
5) Touch #
4) Touch User Code
6) Put Finger-print three times on sensor.
(Blue light flickers)(1st , 2nd , good on FND)
3) Touch #
( good on FND)
2) Touch 3
1) Press M Button on
door back.
User Code
Finger - print 3 times
#M
#
#
M 3
New Code

6
Close the door. Door locks automatically.
*
If door is unlocked when closed the door, Error sign on FND
and sounding “Bi Bi Bi Bi”.
1) Touch Pad 2) Put Finger-print on
sensor
3) Open the door
(OPEnd on FND)
* Paralysis : If unregistered finger-prints entered 5 times, the lock gets paralyzed 5 minutes.
1) No response against pad touch.
2)
Paralysis Rest Time is indicated on FND as Min-Sec.
In case of paralysis rest time 4 minutes and 29 seconds, 4_29 indicated on FND.
3) After 5 minutes, paralysis gets released.
* NOTE : If a unregistered finger-print entered, “bi-bi-bi” sound and ErrOr on FND.
(
CLOSEd on FND)
*
If one finger-print is removed, all the registered finger-prints are erased simultaneously.
1) Press M Button on door back.
4) Touch # .
3) Touch 3
(CLEAr on FND)
2) Touch #
5. Open with Finger-print
7.
Locking
* If door opening state keeps over 90 seconds, the alarm sounds.
6. Delete Finger-prints
Keep door open.
Finger - print Finger - printTouch Pad
##M 3
Close the Door

7
ㆍTwo users can independently open safe with each other’s own user code.
* Multi mode and dual mode can not be used simultaneously.
1) Touch Pad 2) Touch 1st Code
or 2nd Code
3) Touch # 4) Open the door
(OPEnd on FND)
* NOTE : If multi mode unsets, 2nd code is removed automatically. 1st code cannot be removed.
* NOTE : 1) 2nd user code must be different from 1st code.
2)
Prior to closing door, confirm as shown in 8. Multi mode
▶
Open if 2nd Code registered correctly.
3) 2nd code can be changed in the same way as 8. Multi mode
▶
Set .
4) For setting or changing 1st code, please do as shown in 3. Set User Code .
(4 ~16 digits)
1) Press M Button on
door back.
5) Touch # 2) Touch 2
3) Touch #
4) Enter 2nd Code
(good on FND)
1) Press M Button on
door back.
4) Touch # 3) Touch 2
2) Touch #
(CLEAr on FND)
8. Multi mode
Set
Unset
Open
2nd Code
# #M 2
# #M 2
1st
or
2
nd
Code
#
Touch Pad Open the Door

8
ㆍCode and finger-print should be entered in a row for opening.
* Dual mode and multi mode can not be used simultaneously.
* NOTE : 1)
Prior to closing door, confirm as shown in 9. Dual mode(Finger-print+Code)
▶
Open if Finger-print registered correctly.
2) Finger-print can be changed in the same way as 9. Dual mode(Finger-print+Code)
▶
Set .
3) For setting or changing user code, please do as shown in 3. Set User Code .
5) Open the door
1) Touch Pad 2)
Put Finger-print
on sensor
3) Touch
User Code
4) Touch #
(OPEnd on FND)
1) Press M Button on
door back.
4) Touch # 3) Touch 5
2) Touch #
(CLEAr on FND)
1) Press M Button on
door back.
2) Touch 5
3) Touch #
4) If there is no registered fingerprint
Put Finger-print three times on sensor.
(good on FND)
(dUAL on FND)
9. Dual mode (Finger-print + Code)
Set
Unset
Open
Finger
-
print 3 times
#M 5
# #M 5
Finger
-
print User Code
#
Touch Pad
Open the Door

9
* NOTE : If dual mode unsets, 2nd code is removed automatically. 1st code cannot be removed.
* NOTE : 1) 2nd code must be different from 1st code.
2)
Prior to closing door, confirm as shown in 10. Dual mode(Code+Code)
▶
Open if 2nd Code registered correctly.
3) 2nd code can be changed in the same way as 10. Dual mode(Code+Code)
▶
Set .
4) For setting or changing 1st code, please do as shown in 3. Set User Code .
1) Touch Pad 2) Touch
1st Code
6) Open the door
4) Touch
2nd Code
5) Touch # 3) Touch #
(OPEnd on FND)
1) Press M Button on
door back.
4) Touch # 3) Touch 9
2) Touch #
(CLEAr on FND)
(4 ~16 digits)
1) Press M Button on
door back.
5) Touch # 2) Touch 9
3) Touch #
4) Enter 2nd Code
(good on FND)
(dUAL on FND)
10. Dual mode (Code + Code)
ㆍTwo different codes should be entered in a row for opening.
* Dual mode and multi mode can not be used simultaneously.
* While using Dual locking function (Code + Code), finger-print function doesn’t work.
Set
Unset
Open
2nd
Code
# #M 9
# #M 9
1st
Code
#
2nd
Code
#
Touch Pad Open

10
*
Alarm is automatically released when door is opened.
Optional Alarm
Curfew Mode
Press BUTTON
(On / Off )
(LED turns on/off, 10 seconds required)
*
Battery life span : 1year (in alarm setting)
*
In following cases, 9V battery must be replaced.
- If alarm horns more than 30 minutes
- When LED light is not bright enough
Set/Unset
Installing Place alarm loaded with 9V battery on doorback.
3) Touch # 1) Press M Button
on door back.
2) Touch 8
(Alerton FND)
1) Press M Button
on door back.
4) Touch # 3) Touch 8
(CLEAr on FND)
2) Touch #
Button
Battery Housing Cover
LED Light
Push down to open.
ㆍOnce alarm system is affected by shock or tilt, it makes horn immediately.
ㆍWhen Alarm system is set on, some impacts to the safe may cause alarm horning.
ㆍMotion sensor may respond to all kinds of movements.
11. Alarm Setting
Set
Unset
#M 8
# #M 8