Phoenix SPECTRUM LS6000 User manual

SPECTRUM
LS6000
Operating
Instructions

2
Contents Page
1 Batteries 3
2 Opening 4
3 Setting User Code 4
4 Locking 5
5 LED Light 5
6 Multi-user mode & Dual-user mode 6
7 Changing Door Panel 7
Contents
FOR SAFETY
Prior to using the safe, please read the instructions carefully.
Cautions when placing the safe.
The safe is heavy and should be handled very carefully.
Never move the safe with the door open.
Place the safe on at oor.
Cautions when using the safe.
Be careful not to slam the door closed.
Be careful not to trap hands or ngers when closing door.
As the safe is heavy and operated with a smart digital lock, it is not recommended
that children operate the safe.
Be careful not to forget the user code, and keep the instruction outside of the safe.

3
Components
Prior to using safe, install 4pcs of AA alkaline batteries.
(LED ickers, Bi Bi Bi sound, Melody rings for 1 second)
* Non-alkaline and rechargeable batteries are not
recommended.
The batteries need to be replaced when ‘Bi-ric’ sound is
emitted when any button is pressed.
Replace all 4 batteries at the same time.
* Battery life span : 1 year (Average openings 3 times a day)
* When the batteries are replaced, the registered user code is
not erased.
* Note: If the door does not open in spite of the correct user
code being entered, please change the batteries before calling
for service.
Instructions Drawer Shelf Shelf Clips
(4pcs)
1.5V Alkaline
AA Batteries
(4pcs)
Memory Button
LEDLight
Digital Lock
Door Panel
1. Batteries

4
2. Opening
NOTE: If wrong code is tried, Red LED ickers sounding Bi Bi Bi Bi.
Paralysis: If a wrong code is entered 5 times, the lock will be paralyzed for 5 minutes
Remaining paralysis time can be checked via the LED.
Eg) In the case of 4 minutes remaining, LED ickers 4 times every 10 seconds.
Scramble Numbers: The code can be disguised by inserting random numbers either before, after
or both before and after the user code. E.g. user code of 1234, xxx1234, 1234xxx or xxx1234xxx.
Total of 32 numbers can be accepted.
Mute sound: You can hide the button sound.
SET: M 7 #
UNSET: M # 7 #
3. Set User Code
NOTE: 1) Prior to closing the door, check the new code has been registered correctly by
following 2. Opening.
2) It is not recommended to use codes such as a telephone numbers, birthday or
consecutive numbers for security reasons.
1 ) Press C Button
(Bi sound, LED ickers)
2 ) Enter User Code
(LED ickers, Bi sound)
(Factory Code 1 2 3 4)
3 ) Press # Button
(Melody rings)
4 ) Open the door
1 ) Press MButton on the back of the door. 2 ) Enter New Code
(4 ~16 digits)
3 ) Press #Button.
(Melody rings)
Keep the door open.

5
4. Locking
NOTE: 1) Don’t close the door with the bolts in the locked position.
2) If door is unlocked when #button pressed, red LED turns on sounding Bi Bi Bi Bi.
- Door may not be closed because of over inside matters.
Door open alert: If the door is not locked within 1 minute after opening, an alert will sound for
30 seconds.
5. LED Light
1) Close the door 2 ) Press # Button
(LED ickers with melody)
LED turns on for 15 seconds, each time the Cbutton is pressed.

6
6. Multi-user mode & Dual-user mode
Multi-user mode
Multi-user mode: Two users can independently open the safe with their own user code.
Dual-user mode: Two different codes should be entered consecutively to open the safe.
* Both modes can not be used simultaneously.
SET: M 2 # 2nd Code #
NOTE: 1) Prior to closing the door, conrm the 2nd code has been registered correctly by
following 2. Opening
2) 2nd code can be changed in the same way as Multi-user mode > set .
3) For setting or changing 1st code, please do as shown in 3. Setting User Code .
UNSET: M # 2 #
NOTE: When unsetting multi user codes the 2nd code is removed automatically. The 1st code
will be retained.
OPEN: C 1st Code or 2nd Code # Open the door
Dual-user mode
SET: M 9 # 2nd Code #
NOTE: 1) Prior to closing the door, conrm the ngerprint has been registered correctly as
shown in 2. Opening
2) 2nd code can be changed in the same way as the initial set up Dual-user mode > SET
3) For setting or changing the 1st code, please follow the instructions in 3. Set User
Code.
UNSET: M # 9 #
NOTE: When unsetting dual mode, the 2nd code is removed automatically. The 1st code will be
retained.
OPEN: C 1st Code # 2nd Code # Open the door

7
7. Changing Door Panel
When changing the panel please take care not to trap ngers in between the panel and door
frame. It is recommended when replacing the panel with a new one, to wear gloves.
1 ) Hold and adjust the panel to allow the
position guide to locate into the xing hole.
2 ) Push the panel into the door frame to
attach.
1 ) Place a nger into the hinge hole on upper
right side of door frame and push the panel
outwards to detach.
2 ) Lift the panel up to detach.
DETACH PANEL
ATTACH PANEL

Need support?
We’re here if you need us.
Web www.phoenixsafe.co.uk
Email [email protected]
Phone [phone]
Where peace of mind
is guaranteed.