Pixapro LED200B MKIII User manual

Instruction Manual
Model LED200B MKIII
Power Output 200W
Brightness 16,000 lux @ 1m
LED Type Integrated LED Chip
Beam Angle 65°
CRI >95
TLCI >95
Power Range 10-100%`
Heat Dissipation Built-in Fan (<18dB)
Remote Control Yes (Sold Separately - Requires Receiver Dongle)
Adapter Input AC 90-240V~ 50/60Hz
Adapter Output DC 24V / 5A
Adapter Output Port XLR-4 Port
Dimensions 360mm x 250mm x 315mm
Net. Weight 3.6kg
Please read these instructions carefully before using your device for the first time. It includes everything
you need to know to avoid physical injuries and damages.
Please pay attention to all safety notes in this instruction manual.
Please keep this manual safe. In case of selling or leaving the device to other persons, please don’t
forget to hand this manual over as well.
Specifications
CAUTION!
PLEASE READ
INSTRUCTIONS
BEFORE USE

2
Table of Contents
Specifications ..............................................................................1
Parts Diagram ............................................................................. 3
How To Use ................................................................................ 3
Power Input.......................................................................... 3
Power Adjustments.............................................................. 4
Memory Function................................................................ 4
Li ght ID and Group Settings............................................. 4
Overheat Protection............................................................ 5
Optional Acessories................................................................... 5
Troubleshooting........................................................................... 5
Health & Safety Precautions.......................................................5
Contact Information.................................................................... 6
CAUTION!
DO NOT Look Directly Into The Light
Important Information... Please Read

3
Parts & How To Use
6. Power Switch
7. Power Input Port
8. Reflector
9. Yoke Bracket
10.Umbrella Locking Screw
11 . Stand Locking Screw
12. Modifier Release
13. Angle Adjustment Screw
14. Handle
15. LED Chip
1. Colour Temperature Dial
2. Parameter Store/Read Button
3. USB Receiver Port
4. LCD Screen
5. Power Dial
1. Power Input
Connect the power adapter, to the Power Input port (7), located at the back of your LED200B MKIII. Please
pay attention to orientation of the bayonet on the power connector. You should hear a “click” which indicates
that your power adapter is securely connected to your LED200B MKIII unit. Once connected, plug your power
adapter into the mains power socket, and switch on the power switch (6). LCD display (4) should then light-up to
indicate that the unit is ready for use.
2. Power/Colour Tempterature Adjustment
To control the Power output, rotate power dial (5) clockwise, the power will increase in increments of10%. if you
rotate the power dial in an anti-clockwise direction, power decrease in 10% increments for quick adjustments.
For more precise power adjustments, press power dial (5) in once, and the percentage on the display should
blink. Rotate the dial in a clockwise direction, and the power increase by increments of 1% for every click; Rotate
the dial in an anti-clockwise direction, and the power decrease by increments of 1% for every click;
The Power range goes from 0-100%. 100% represents full power status, and 0% represents off power status.
To control the Colour-Temperature, rotate the Colour-Temperature dial (1) cloackwise, and the Colour-Temper-
tature will increase up to 5600K (Daylight Balanced. If you rotate the colour-temperature dial anti-clockwise, it
decrease down to 3200K (Tungsten Balanced).
How To Use

4
3. Memory Function
The parameter storage/recall buttons (2), from left to right, are M1, M2, M3, and M4. Press and hold for two
seconds to store parameter settings and short press to recall storage parameters. For example, if you want to
store certain power settings, press and hold the key M3 for 2 seconds. The “M3” appears in the lower right
corner of the LCD display, e.g. the current power and colour temperature parameters are stored. When the pa-
rameters are changed, if you need to use the previously stored power settings again, simply press the M3 key to
restore the original parameters.
4. Light ID and Group Settings (For Optional Remote Control)
Insert the optional PiXAPRO 2.4GHz remote control receiver into the USB receiver socket (3) located at the back
of the LED200B MKIII unit. Together with the optional PiXAPRO 2.4GHz radio remote, you can wirelessly and
remotely control the power of your LED200B MKIII light
Simply insert the remote control receiver into the USB receiver port
(3) and turn on the main power switch (6). The red indicator light on
the remote receiver should flashes, indicating that the communication
connection is normal. At the same time, the LCD screen automatically
switches to the interface shown in the figure to the right. Set the remote
transmitter to the same Light ID Number as set on the LED head, and
you should now be ale to remotely control the light.
Light ID number setting: After pressing and holding the power dial (5) for two seconds, the “G0” icon on the LCD
screen starts flashing. Now use the power dial (5) to set your groups on the flash ( G0-G9); Press the power dial
(5) again and the “L0” “ icon on the LCD screen should start blinking. Now use the power dial (5) to set your
light-number on the flash ( L0-L9). Once you are happy with your settings, press the power dial (5) in again to
confirm and save your settings. You can also leave your adjustments for about 2 seconds to automatically save.
The LED200B MKIII can be set to a total of 100 Light numbers.
How To Use
2.4GHz Wireless
Remote Control
2.4GHz Wireless
Receiver Dongle

5
Description Possible Cause Possible Solutions
Nothing Happens When Power is
Switched on.
Power shows 10% Rotate Power-Dial in a Clockwise
Direction
Power adapter does not match
Please use power adapter that
comes supplied with the LED200B
MKIII Unit
Low Battery Charge Battery Before Use
Circuit Board Damaged Please Return to Vendor for Repair
Lack of Brightness Over-heat Protection has been
activated
Leave adequate cooling time be-
fore use
When turn on the light, the battery
displays inaccurate. Low battery
when increase brightness, full bat-
tery when decrease brightness.
Battery display test indicated usage
of time length in the current bright-
ness. Increase brightness requires
more battery; the usage time is
short, so battery display shows less
Normal
Items shown on LCD display are
incomplete, or the back-light is not
turning on.
LCD Display is malfunctioning Please Return to Vendor for Repair
How To Use
Troubleshooting
5. Overheat Protection
The LED200B MKIII features a built-in temperature controller and an ultra-quiet cooling fan (<18dB), strictly to
regulate the temperature of the LED200B MKIII body. Since the LED200B MKIII uses the rear-conduction heat
dissipation method, the heat from the LED chip is channelled directly to the LED200B MKIII’s housing where the
heat is dissipated.
If the temperature of the shooting environment is too high, the LED200B MKIII’s body temperature will increase. If
it rises above about 58°C, the output power will be automatically reduced by 50% to protect the LED chip from
overheating and sustaining permanent damage. If the temperature of the LED200B MKIII continues to increase,
the LED chip will automatically switch-off until the unit cools back down to a safe working temperature. After
restarting, the LED200B MKIII everything should go back to normal.
Optional Accessories
Optional accessories for the PiXAPRO LED200B MKIII include:
2.4GHx Wireless Remote control, 2.4GHz Wireless remote control receiver dongle, S-Type fitting soft-
boxes, reflectors, barn door sets etc. (Sold Separately).

6
Health & Safety Precautions
DO NOT touch or allow anything to make direct contact with the LED chip whilst LED200B MKIII is in use or is cool-
ing down. May burn the skin, or cause permanent damage to the LED.
DO NOT cover the LED200B MKIII body whilst in use, as it can affect heat dissipation, and cause the LED200B
MKIII unit to overt-heat, which may cause permanent damage.
ENSURE the device is given sufficient cooling-down time (approximately for 15 minutes for every hour of use) before
storage.
Please store LED200B MKIII unit in a cool dry place.
DO NOT expose the LED200B MKIII to direct sunlight, moisture, dust, chemical solutions, gasoline, grease, oil, paint,
or detergents etc. May cause permanent damage to your LED200B MKIII head unit.
DO NOT look directly into, or place Led chip at close proximity to the eyes of people or animals. Please use
:LED200B MKIII at a distance of at least 1m away from your subject unless diffused.
ENSURE the device is properly disconnected the power supply when the light is not in use, before mounting or during
maintenance.
PLEASE ENSURE your device is checked by qualified Technician before switching on again, if you LED200B MKIII
has suffered any falls or hard impacts.
ENSURE all the inflammable materials are kept away from the LED100K MKIII.
DO NOT insert metal object into the LED200B MKIII housing
DO NOT touch power cord with wet hands. Risk of electrocution
When disconnecting the Power-Cord, please pull out by the plug, and not by the cable.
DO NOT attempt to repair light. If your LED200B MKIII develops a fault, as doing so will VOID your warranty. Please
contact us at [e-mail]
DO NOT dismantle the head unit unless work is carried out by a qualified technician. Dismantling your LED200B
MKIII will VOID your warranty.
50 Popes Lane, Oldbury,
West Midlands, B69 4PA
0121 5 52 3113
[email protected]