PLANEPRINT BLERIOT XI Programming manual

You can find the STL data
at www.planeprint.com
NOTE: Slicing only
works with CURA!
PRINTING & ASSEMBLING MANUAL

BLÉRIOT XI 2
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PLA TPU CARBON

BLÉRIOT XI 3
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
RC Components
ENGINE AXI 2203/40 VPP or comparable indoor-20 grams-motors.
31 mm
or comparable indoor-20 grams-motors.
PROP 8x3.8 or comparable, also possible 8x3, 8x4
BEC-CONTROLLER 15 A (one matching the motor)
RECEIVER 3 Channel
BATTERY 2S Lipo, 650 MaH (ideal weight 38 grams)
SERVOS • Stemedu Micro 3.7g Servo GH-S37D
• PLANET-HOBBY ECO PLUS
• PICCO 8 DIGITAL SERVO
• Diamond D47
• Hitec HS 40 Eco Servo 4,8g
or similar in the same size, 2 pieces
There are also ready-made indoor drive sets with motor, servos and battery available from many dealers.
max. 22 mm max. 8.5 mm
max. 27 mm
Required accessoires – basic equipment
• Tough PLA (or PLA), ~200 grams
• LW TPU like VarioShore, ~20 grams (or TPU A95)
• CA super glue (liquid and liquid medium or thick)
• CA activator
• Wood glue
• Carbon rod Ø2*1000mm, 1 piece
• Carbon rod Ø0.8*1000mm (also possible is Ø1mm), 2 pieces
• Steel wire Ø0.8mm (a few short pieces for the linkage)
• Parchment or tissue paper (or another light paper to cover the wings)
• black and gold acrylic paint and thin gray twine
• some tapping screws Ø2 mm
• Hair gums or small rubber bands
Tools
Cutter knife, Scissors, small Philips screwdriver, Sandpaper, small brush

BLÉRIOT XI
4
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
Printing the parts – Printing profiles
This manual is constantly being improved and supplemented, we recommend downloading
the latest version from our website before building.
The Blériot XI requires :
PROFILE P1_Fullbody,PROFILE P2_Hollowbody and PROFILE P4_Flex
The development of a complex, airworthy RC flight model to express on any stan-
dard 3D printer is a very complex and extensive process. Therefore, we appeal to
your fairness not to forward the STL data you have acquired to third parties.
Thank you for your understanding and have fun with your PLANEPRINT MODEL!
Important for the
1-wall-print (P3, P5)!
In order to print airfoils of the lowest possi-
ble weight with high stability, it is necessa-
ry to print with only one wall line (Nozzle 0.4
mm). Decisive here is the adhesion between
the layers! To achieve this, you must print at
a much higher temperature than normal. As
a guideline, 230° C is a good starting point.
The parts-cooling fan should be set to 0% or
a maximum of 20%. Since not every printer
works the same, it may be necessary to make
small adjustments to these settings.
For slicing all Planeprint
models, these profiles have
to be created in Cura:
PROFILE P1_Fullbody
PROFILE P2_Hollowbody
PROFILE P3_Surface
PROFILE P4_Flex
PROFILE P5_Gyroid
You can find the description at
www.planeprint.com/print

P1_Gear_bl.stl
MATERIAL PLA, Weight: ~ 6 g
ADDITIONAL SETTINGS
None required
TIP These parts should be black, you can
paint them with acrylic paint or print them
with black filament.
This part is not needed
(serves to optimize the paths)
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Elevator_bl.stl
MATERIAL PLA, Weight: ~ 10 g
ADDITIONAL SETTINGS
None required

P1_Grid 1_bl.stl
MATERIAL PLA, Weight: ~ 15 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Grid 1 side_bl.stl
MATERIAL PLA, Weight: ~ 7 g
ADDITIONAL SETTINGS
None required

P1_Grid 2_bl.stl
MATERIAL PLA, Weight: ~ 10 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Grid 2 side_bl.stl
MATERIAL PLA, Weight: ~ 6 g
ADDITIONAL SETTINGS
None required

P1_Grid 3_bl.stl
MATERIAL PLA, Weight: ~ 8 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Grid 3 side_bl.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required

P1_Grid 4 side_x2_bl.stl
MATERIAL PLA, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Grid 4 down_bl.stl
MATERIAL PLA, Weight: ~ 4 g
ADDITIONAL SETTINGS
None required

P1_Grid 5_bl.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody Tough PLA (or PLA)
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Grid 4 up_bl.stl
MATERIAL PLA, Weight: ~ 4 g
ADDITIONAL SETTINGS
None required