PLANEPRINT WANNA PLAY II Programming manual

PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
NOTE:
Slicing works best
with CURA!
www.planeprint.com
the ONLY place where you can get
original Planeprint STL files legally!
Reno Air race biplane

WANNA PLAY II 2
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PLALW-PLA TPU CARBON

WANNA PLAY II 3
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
Required accessoires
Filament
• LW-PLA (cannot be replaced by PLA!), ~1500 grams
• PLA oder better Tough PLA, ~320 grams
• TPU A95, ~20 grams
• LW-TPU Colorfabb VarioShore about 100 grams
(strongly recommended for tires, but it also works with normal TPU)
Materials
• some tapping screws
(search for: M2 flat head tapping screw assortment)
• CA super glue (liquid and liquid medium)
• CA activator
• Metal screw 3*40mm with nuts (not self-locking!), 4 pieces
• Metal screw 3*20mm with self-locking nuts, 4 pieces
• Metal screw 3*30mm, 2 pieces
• Ball bearings 3x6x2,5mm, 4 pieces
• Carbon tube Ø8mm*1000mm (inside 6mm), 4 pieces*
• Carbon rod Ø3*1000mm, 1 piece*
• Steel wire Ø1*1000mm, 2 pieces
• Self-adhesive Velcro tape
• Velcro strap
• Servo cable extension 350mm, 2 pieces
• Rod connection, 4 pieces
• Neodym-Super-Magnet 5x5x5mm, 4 pieces
• some Hair gums
• some lead to correct the CG
Tools
Cutter knife, small Philips screwdriver, Sandpaper,
Metal saw, Needle nose pliers.
*Cut the 8mm tubes into the following parts:
Tube 1 for the gear: 2x125, 2x158
Tube 2 for the wings: 2x500
Tube 3 for the wings and HS: 1x800, 1x120
Tube 4 for the wing: 1x1000 (do not cut)
*Cut the 3mm rod into the following parts:
Motormount: 4x200
Metal screw 3*40mm, 3*20
Rod connection
Carbon tube
Magnet 5x5x5mm
Tapping screws 2mm
Hair gums
Ball bearings
6 mm
3 2.5

WANNA PLAY II 4
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
RC Components
ENGINE PROPDRIVE V2 3548 900KV (HobbyKing) or comparable motors.
You can also use any other motor that fits a 14x7 propeller!
NOTE Tthis motorization is very powerful. The Wanna Play is not
full throttle safe with it. Always be careful, it is up to your discretion
and the quality of your printing and assembly as to what stresses
the aircraft can withstand.
The optimal length of the motor is when the distance to the back of the prop is 58 mm.
If the motor is shorter, you can use longer screws and washers. If the motor is longer, the
motor cross can also be mounted behind the motor mount. In this case the diameter of the
motor must not be more than 35 mm!
PROP 12x7 or 14x6
BEC-CONTROLLER 80 A (must fit the engine!)
RECEIVER 5 Channel
BATTERY 4S Lipo, 3500 – 5000 MaH
(The battery should have a weight of 400 to 450 grams)
SERVOS 4 pieces like Corona DS-238MG or comparable
Dimensions (The optimal distance between screws is 35 mm):
max. 30 mm max. 15 mm
max. 30 mm
43 to 50 mm
58 mm
Rear mounting Prop

WANNA PLAY II
5
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
Printing the parts – Printing profiles
For the new PROFILE P5_Gyroid it is essential to use Cura Version 5 or later, It will work with
older versions, but the weight of the parts will be higher and the printing time longer.
This manual is constantly being improved and supplemented, we recommend downloading
the latest version from our website before building.
The development of a complex, airworthy RC flight model to express on any stan-
dard 3D printer is a very complex and extensive process. Therefore, we appeal to
your fairness not to forward the STL data you have acquired to third parties.
Thank you for your understanding and have fun with your PLANEPRINT MODEL!
Important for the
1-wall-print (P3, P5)!
In order to print airfoils of the lowest possi-
ble weight with high stability, it is necessa-
ry to print with only one wall line (Nozzle 0.4
mm). Decisive here is the adhesion between
the layers! To achieve this, you must print at
a much higher temperature than normal. As
a guideline, 230° C is a good starting point.
The parts-cooling fan should be set to 0% or
a maximum of 20%. Since not every printer
works the same, it may be necessary to make
small adjustments to these settings.
For slicing all Planeprint
models, these profiles have
to be created in Cura:
PROFILE P1_Fullbody
PROFILE P2_Hollowbody
PROFILE P3_Surface (Not necessary for this plane)
PROFILE P4_Flex
PROFILE P5_Gyroid
You can find the description at
www.planeprint.com/print
PROFILE P5_Gyroid
It is essential for the necessary stability of the LW parts
printed with PROFILE_5 are as stable as possible. Please
use a test part to check the strength by fracture tests. It must
not break along the layer lines under any circumstances! Also
note that the printing temperature for LW-PLA is as low as
possible to obtain a wall thickness of 0.4 to 0.6 mm at a flow
of 60 to 70 % (depending on brand).
Caution: at too high temperatures, LW-PLA becomes brittle
and breaks more easily.

WANNA PLAY II
6
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Interconnects_wp.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Gear parts_wp.stl
MATERIAL PLA, Weight: ~ 45 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
7
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Motormount_wp.stl
MATERIAL PLA, Weight: ~ 18 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Motormount base_wp.stl
MATERIAL PLA, Weight: ~ 21 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
8
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Protectors FUS_wp.stl
MATERIAL PLA, Weight: ~ 11 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Parts_wp.stl
MATERIAL PLA, Weight: ~ 19 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II 9
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Parts rear_wp.stl
MATERIAL PLA, Weight: ~ 9 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Protectors WING_wp.stl
MATERIAL PLA, Weight: ~ 11 g
ADDITIONAL SETTINGS
None required
Remove support.
Please be careful with the knife!

WANNA PLAY II
10
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Servo board 35mm_wp.stl or
P1_Servo board customizable_wp.stl
MATERIAL PLA, Weight: ~ 5 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Rear gear_wp.stl
MATERIAL PLA, Weight: ~ 4 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
11
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Strut parts_wp.stl
MATERIAL PLA, Weight: ~ 7 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Spinner plate 6_wp.stl
MATERIAL PLA, Weight: ~ 12 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
12
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Winglets_wp.stl
MATERIAL PLA, Weight: ~ 11 g
ADDITIONAL SETTINGS
None required
P1_Clips 1mm wire.stl
MATERIAL PLA, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
13
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
Carbon tool 8mm.stl
MATERIAL PLA, Weight: ~ 6 g
ADDITIONAL SETTINGS
None required
Use this tool to cut the 8mm carbon tubes.

WANNA PLAY II
14
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P2_Cowling lock_wp.stl
MATERIAL PLA, Weight: ~ 5 g
ADDITIONAL SETTINGS
None required
PROFILE P2_Hollowbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P2_Hollowbody.
Please note the additional settings for the individual parts!
P2_Battery mount_wp.stl
MATERIAL PLA, Weight: ~ 20 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
15
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P2_Parts_wp.stl
MATERIAL PLA, Weight: ~ 13 g
ADDITIONAL SETTINGS
None required
PROFILE P2_Hollowbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P2_Hollowbody.
Please note the additional settings for the individual parts!
P2_Gearbase L_wp.stl and
P2_Gearbase R_wp.stl
MATERIAL PLA, Weight: ~ 20 g
ADDITIONAL SETTINGS
• Infill Pattern: Gyroid

WANNA PLAY II
16
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P2_Servocovers_wp.stl
MATERIAL PLA, Weight: ~ 11 g
ADDITIONAL SETTINGS
None required
PROFILE P2_Hollowbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P2_Hollowbody.
Please note the additional settings for the individual parts!
P2_Rim bearings_wp.stl
MATERIAL PLA, Weight: ~ 7 g
ADDITIONAL SETTINGS
• Wall Line Count: 3
There is also a rim version STL without
ball bearing, but we recommend the
variant with ball bearing!

WANNA PLAY II
17
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P2_Hollowbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P2_Hollowbody.
Please note the additional settings for the individual parts!
P2_Strut_wp.stl
MATERIAL PLA, Weight: ~ 12 g
ADDITIONAL SETTINGS
• Infill Density: 6 %
• Print twice

WANNA PLAY II
18
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P4_Flex
The following parts must be sliced with the PROFILE P4_Flex.
Please note the additional settings for the individual parts!
P4_Hinges_wp.stl
MATERIAL TPU A95, Weight: ~ 2 g
ADDITIONAL SETTINGS
None required
P4_Rear wheel_wp.stl
MATERIAL TPU A95 or better VarioShore,
Weight: ~ 2 g
ADDITIONAL SETTINGS
VarioShore with Flow 70 %:
• Infill Density: 100 %
TPU A95:
• Infill Density: 100 %

WANNA PLAY II
19
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P4_Flex
The following parts must be sliced with the PROFILE P4_Flex.
Please note the additional settings for the individual parts!
P4_Rubber bands_wp.stl
MATERIAL TPU A95, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required
P4_Tension belts 125_wp.stl
MATERIAL TPU A95, Weight: ~ 4 g
ADDITIONAL SETTINGS
None required

WANNA PLAY II
20
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P4_Flex
The following parts must be sliced with the PROFILE P4_Flex.
Please note the additional settings for the individual parts!
P4_Tire_wp.stl
MATERIAL TPU A95 or better VarioShore,
Weight: ~ 55 g
ADDITIONAL SETTINGS
VarioShore with Flow 70 %:
• Wall Line Count: 6
• Top Layers: 6
• Bottom Layers: 6
• Infill Density: 15 %
• Infill Pattern: Gyroid
• print this part twice
TPU A95:
• Wall Line Count: 3
• Top Layers: 3
• Infill Pattern: Gyroid