PLANET ECLIPSE SL Series Owner's manual

FOR SL94 EGO
V1
FEATURE
SUPPLEMENT

CONGRATULATIONS,
Thank you for purchasing an SL-94 Ego marker. The SL range represents
the very best of Eclipse in terms of cutting edge performance and
technology that deliver on our philosophy of refined design and super
fast markers that produce devastating firepower!
I know you’ll be blown away with your new Eclipse SL-94, but before
you use your Marker please read through this Feature Supplement
as well as the Ego9 Operation Manual in its entirety and pay particular
attention to all of the Warnings and Safety Guidelines. If you are missing
either the Feature Supplement or the Ego9 Operational Manual both can
be downloaded from the Downloads page at :
www.planeteclipse.com
At the back of this supplement is a section that will allow you to record and
track your Markers Service History.
If you have any questions or problems turn to the Dealers & Service
Section in the Operation Manual where you
will find a list of accredited Dealer Service
Centres that will be able to help you out
or of course you can always contact
Nicky T in our Tech Support
Department directly on:
[e-mail]
04 SL SHAFT3 BARREL KIT
05 SL94 FIXED OUTPUT LPR
05 ZICK 2 RAMMER SYSTEM
06 ADDITIONAL TRIGGER SYSTEMS
07 FSD DELAY PARAMETER
07 CURE 3 BOLT SYSTEM
08 SERVICE HISTORY
JACK WOOD - CHIEF ENGINEER
READ AND ADHERE STICTLY TO ALL OF THE
SAFETY INSTRUCTIONS AND GUIDELINES IN
THE EGO9 OPERATORS MANUAL!

SL94 FIXED OUTPUT LPR
ZICK 2 RAMMER SYSTEM
LPR CAP
#013 NBR
70
LPR PISTON
SPRING
LPR PISTON
#14x2 NBR 70
OR #016 NBR 70
#010 NBR 70
Your Eclipse SL comes as standard with an Eclipse SL Shaft 3 barrel.
The barrel screws into the body of the SL using a right hand thread meaning
that if you hold the SL pointing away from you the barrel screws into the
body in a counter-clockwise direction.
The barrel comprises of two parts, a barrel back Aand a barrel front B .
The two parts are joined together with a left hand thread meaning that
if you hold the barrel, with the back nearest you, the front unscrews in a
counter-clockwise direction. The bore size of the barrel back is engraved at
the end of the barrel back C.
On the barrel back there is a 016 NBR 70 o-ring D which prevents the barrel
from vibrating loose from the SL body when the marker is fired. There is also
a 015 NBR 70 o-ring on the barrel front E helps with alignment when the
two sections are screwed together.
Replace and lubricate these o-rings with Eclipse Grease as necessary.
SL SHAFT3 BARREL KIT
C
D
A
E
B
NOTE: THE SL WILL ONLY ACCEPT COCKER THREADED
BARRELS. DO NOT USE ANY OTHER TYPE OF BARREL
THREAD.
NOTE: WHEN INSTALLING THE FIXED OUTPUT LPR CAP, DO NOT
USE THE SMALL LPR ADJUSTER SPRING IN THE FRONT OF THE
PISTON FROM THE ADJUSTABLE LPR CAP. INSTALLING THE SMALL
LPR SPRING INTO THE FRONT OF THE FIXED LPR CAP WILL CAUSE
THE OUTPUT PRESSURE TO DROP TOO LOW AND CAUSE LOW AND
INCONSISTENT VELOCITIES.
NOTE: THE BORE SIZE OF YOUR SHAFT 3 MAY VARY ACCORDING TO THE
MODEL OF SL YOU HAVE.
#009 NBR 70
ZICK 2 RAMMER
#009 NBR 70
#011 NBR 70
CUSHION
ZICK 2
CAP
#010 NBR 70
#011 NBR 70
BUMPER
FEATURE SUPPLEMENT
4
FEATURE SUPPLEMENT
5

FSD DLY
THE FIRST SHOT DROP OFF
DELAY PARAMETER
This parameter sets the amount of time after the last shot before the FSD
COMP is used on the next shot. The first shot after powering on the SL94
will always have FSD COMP. This parameter can be set between 30 and
240 seconds in 10 second increments.
THE SL94
TRIGGER SYSTEMS
The SL94 comes with two complete trigger systems (bearing carrier, trigger,
spring and set-screws) that are interchangeable with the SL94 frame.
For full details of how to change the trigger system in the SL94 please
consult the “Ego9 Trigger Assembly” section in the Ego9 Operators
Manual. If you have any doubts about how to conduct this procedure then
do not hesitate to contact your nearest Eclipse Service Center (see Eclipse
Certified Service Center pages of Ego9 Operators Manual).
For full details of how to adjust your trigger please refer to the Setting th
Trigger Section of the Ego9 Operators Manual.
IMPORTANT
When setting the trigger it is essential to ensure that the electronic trigger
detection is working correctly. When the trigger is fully depressed the
Trigger Detection Indicator (TDI) should point upwards . When
the trigger is fully released the TDI should point downwards .
For more information, see Understanding the Trigger Detection Indicator
(TDI) and Filter Menu in the Ego9 Operators Manual.
ASpring
BSpring Return Strength Screw
CTrigger Pin Locking Screw
DFront Stop Trigger Screw
EMagnet Return Strength Screw
FMicro Switch Activation Screw
GRear Stop Trigger Screw
C
G
F
B
A
ED
C
G
F
B
A
ED
WARNING: REMOVE ALL PAINTBALLS & DE-GAS YOUR MARKER,
DISCHARGING ANY STORED GAS IN A SAFE DIRECTION,
DISCONNECT THE BATTERY & REMOVE THE BARREL, LOADER & AIR SYSTEM
TO MAKE THE MARKER EASIER & SAFER TO WORK ON.
BOLT PLUNGER
BOLT SPRING
#015 NBR 70
BOLT PIN
NOTE: FOR FULL INSTRUCTIONS OF HOW TO ADJUST THE FSD DLY
PARAMETER PLEASE CONSULT THE ADVANCED SET-UP SECTION OF THE
EGO9 OPERATORS MANUAL.
CURE 3 BOLT SYSTEM
FEATURE SUPPLEMENT
6
FEATURE SUPPLEMENT
7

SERVICE HISTORY
WORK UNDERTAKEN:SERVICE STAMP: SERVICE STAMP:
SERVICE STAMP: SERVICE STAMP:
SERVICE STAMP: SERVICE STAMP:
DATE: SIGNATURE: DATE: SIGNATURE:
DATE: SIGNATURE: DATE: SIGNATURE:
DATE: SIGNATURE: DATE: SIGNATURE:
WORK UNDERTAKEN:
WORK UNDERTAKEN:
SERVICE HISTORY
WORK UNDERTAKEN:
WORK UNDERTAKEN:
WORK UNDERTAKEN:
FEATURE SUPPLEMENT
8
FEATURE SUPPLEMENT
9

NOTES NOTES
FEATURE SUPPLEMENT
10
FEATURE SUPPLEMENT
11

UK & EUROPE
Units 5-8 Southfield Ind Est, Praed Road Trafford Park, Manchester, England, M171SJ
Call: [phone]
USA & CANADA
Suite 4, 84 Cutler Street, Warren, Rhode Island, 02885, USA
Call: 401 247 9061
Licensed under one or more of the following patents:
US 6311682, 6615814, 5881707, 5967133, 6035843, 6474326B1, 6637421B2 UK GB 234270, GB 2345953
© Copyright 2009 Planet Eclipse Ltd. SL, and the SL94 device are either trademarks, design trademarks or registered trademarks of Planet Eclipse Ltd.
SL09V1