Planet FT-722 User manual

Fast Ethernet Media Converter
100Base-FX
Multi-mode to Single-mode

Trademarks
Copyright PLANET Technology Corp. 2004.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology
Corp. The information in this manual is subject to change
without notice. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will
work properly in all environments and applications, and makes
no warranty and representation, either implied or expressed,
with respect to the quality, performance, merchantability, or
fitness for a particular purpose.
PLANET has made every effort to ensure that this User s
Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User sManual is subject to change without
notice and does not represent a commitment on the part of
PLANET. PLANET assumes no responsibility for any
inaccuracies that may be contained in this User s Manual.
PLANET makes no commitment to update or keep current the
information in this User s Manual, and reserves the right to
make improvements to this User s Manual and/or to the
products described in this User s Manual, at any time without
notice.
If you find information in this manual that is incorrect,
misleading, or incomplete, we would appreciate your
comments and suggestions.

1
FCC Warning
This equipment has been tested and found to comply with the
regulations for aClass Adigital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with this
user s guide, may cause harmful interference to radio
communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the user
may be required to take adequate measures.
Revision
User's manual for PLANET Fast Ethernet Converter
Model:FT-722
Rev 1.0 (March.2004)
Part No. 2010-000030-000

2
1. Overview
Thank you for purchasing PLANET FT-722 Fast Ethernet
Fiber-optic Media Converter. This converter is used to convert
one type media signal to other type equivalent that allowstwo
type segments connect easily, efficiently and inexpensively.
This converter can be used as astandalone unit or as a
slide-in module to the 10”/19”media chassis (up to 15 units)
for aTP and Fiber combined networks at acentral wiring
closet. Please contact with your sales representative for more
about the 19”media chassis.
2. Model List
Your Fast Ethernet Converter comes with one of the following
models.
ð FT-722Sxx: two on board SC fiber connectors
Sxx represents Single-model optic interface in xx kilometers.
In the following sections, the term “FT-722”indicates the
product above, the term “MM”and “SM”represents
Multi-mode and Single Mode fiber-optic mode.
3. Checklist
Your FT-722 carton should contain the following items:
ð The Fast Ethernet Media Converter
ð AC-DC Power Adapter (Output: 5VDC, 2 A max.)
ð This user s manual
If any item is missing or damaged, please consult the dealer
from whom you purchased your Fast Ethernet Converter.

3
4. Product Outlook
Left View
There are two fiber-optic connectors, multi-mode on the left,
single-mode on the right and three LED indicators.
PWR
RX
Multi-ModeSingle-Mode
TXRXTX
Fast Ethernet Converter
LNK/ACT
Right View
One DIP switch for Link Fault Pass Through (LFP) feature,
“ON”to turn-on the LLCF and LLR detection (default). And
“OFF”to turn –off this feature.
5V DC
+OFF
LFP
ON

4
5. Installing the Converter
Please followthese steps to install the converter:
• Turn off the power of the device/station in anetwork to
which the FT-722 will be attached
• Ensure that there is no activity in the network
• Attach MM fiber cable from the FT-722 to the MM fiber
network. TX, RXmust be paired at both ends
• Attach SMfiber cable from the FT-722 to the SMfiber
network. TX, RXmust be paired at both ends.
• Connect the 5VDC power adapter to the FT-722 and
verify that the Power LED lights up.
• Turn on the power of the device/station, the LNK /ACT
LEDs should light when all cables are attached.
100Base-FX
Multi-mode
Fiber Network
FT-722
100Base-FX
Single-mode
Fiber Network
100Base-FX
Multi-mode to Single-mode
Note:
n To prevent from optic acceptor malfunction, check the
both end including, connectors, cable type (MM/SM), and
wiring distance before power on the Media Converter.
n DIP-switch LFP is turn on by default, any broken link will
cause the other end link down as well. To diagnose which
end is broken, please turn off the LFP and power off/on the
converter again. Please remains it on in normal operation.

5
6.LED indication
LED COLOR DESCRIPTION
Blinks: when any FXpackets transmitting
and receiving
LNK /
ACT Green
Lit: when Fiber connection is good
PWR Green Lit when +5VDC power detected
7. Cable Connection Parameter
Fast Ethernet 100Base-FXnetworks allow512bit time delay
between any two-node stations in a collision domain.
The overall bit time of Fiber wires and devices must be within
512bit time in segment. To extend the distance, you may use
switch to break up acollision domain and extend the distance.
The limitations are as below:
Duplex Connection Limitation (max.)
Multi-Mode
MM Half Node to Node
Node to Switch 412 meters*
MM Full Node to Node
Node to Switch 2 kilometers
Single-Mode
SMHalf Node to Node
Node to Switch 412 meters*
SMFull Node to Node
Node to Switch Varies on model
Note:
n In half-duplex mode, 412 meters is the maximum distance
between two devices. To force both devices to full-duplex
for optimal distance is strongly recommended.

6
8. FT-722 Technical Specifications
The FT-722 comes with the following standard features:
• Standard: IEEE802.3u, 100Base-FX, IEEE802.3xFlow
control
• Connectors
ð One Fiber-optic, 1310nm wavelength, MM
ð One Fiber-optic, 1310nm wavelength, SM
• Data Transfer Rate: 100Mbps, 200Mbps (full-duplex)
• LED indicators: PWR, LNK/ACT
• Power Requirement: 5V DC, 2A
• Ambient Temperature: 0°to 50°C (operating)
• Humidity: 5% to 90% (non-condensing)
• Dimension: 26 x70 x97mm (HxWxD)
• Cable:
ð Fiber: MM: 50/125 µm or 62.5/125 µm optic fiber
ð Fiber: SM: 8.3/125, 8.7/125, 9/125 µm optic fiber
Connecting to Router, Bridge, or Switch, Hub, please refer to
the device s Technical Manual.
9. Power information
The power jack of FT-722 is with 2.5mm in the central post
and required +5VDC power input. It will conform to the
bundled AC-DC adapter and Planet sMedia Chassis. Should
you have the problem to make the power connection, please
contact your local sales representatives.
Please keep the AC-DC adapter as spare parts when your
FT-722 is installed to a Media Chassis.
Part No. 2010-000030-000