Planet WBS-202N User manual

User’s Manual
www.PLANET.com.tw
802.11n 300Mbps
Outdoor Wireless CPE
WBS-202N/WBS-502N

I
Copyright
Copyright 2018 by PLANET Technology Corp. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not PLANET, its distributor, or its dealer) assumes
the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting
from any defect in the software. Further, PLANET reserves the right to revise this publication and to
make changes from time to time in the contents hereof without obligation to notify any person of such
revision or changes.
All brand and product names mentioned in this manual are trademarks and/or registered trademarks of
their respective holders.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
To assure continued compliance, use only shielded interface cables when connecting to computer or
peripheral devices. Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired
operation.

I
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 26cm
between the radiator & your body.
CE Compliance Statement
This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general
public to electromagnetic fields by way of health protection. The device complies with RF
specifications when it is used at a safe distance of 20 cm from your body.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it.
However, special attention must be paid to the dangers of electric shock and static electricity when
working with electrical equipment. All guidelines of this and of the computer manufacture must
therefore be allowed at all times to ensure the safe use of the equipment.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following the EU
directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country Restriction Reasons/remarks
Bulgaria None General authorization required for outdoor use and
public service
France
Outdoor use;
limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy None If used outside of own premises, general authorization is
required
Luxembourg None General authorization required for network and service
supply(not for spectrum)
Norway Implemented This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian
Federation
None Only for indoor applications
Note: Please don’t use the product outdoors in France.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.

II
Revision
User Manual of PLANET 802.11n 300Mbps Outdoor Wireless CPE
Model: WBS-202N / WBS-502N
Rev: 1.0 (June, 2018)
Part No. EM-WBS-202N_WBS-502N _v1.0 (2081-E10730-000)

III
CONTENTS
Chapter 1.Product Introduction...........................................................................................................1
Package Contents...............................................................................................................11.1
Product Description............................................................................................................21.2
Product Features.................................................................................................................61.3
Product Specifications .......................................................................................................71.4
Chapter 2.Hardware Installation........................................................................................................10
Product Outlook................................................................................................................102.1
2.1.1 Port and Button.......................................................................................................12
2.1.2 Hardware Description.............................................................................................12
Chapter 3.Connecting to the CPE .....................................................................................................13
System Requirements ......................................................................................................133.1
Installing the CPE..............................................................................................................133.2
Chapter 4.Quick Installation Guide ...................................................................................................15
Manual Network Setup -- TCP/IP Configuration.............................................................154.1
4.1.1 Configuring the IP Address Manually .....................................................................15
Starting Setup in the Web UI............................................................................................194.2
Chapter 5.Configuring the CPE .........................................................................................................20
Wizard.................................................................................................................................205.1
Gateway Mode...................................................................................................................215.2
5.2.1 WAN Settings..........................................................................................................22
5.2.2 Wireless..................................................................................................................23
Repeater Mode ..................................................................................................................245.3
WISP Mode.........................................................................................................................265.4
AP Mode.............................................................................................................................275.5
Super WDS Mode ..............................................................................................................285.6
Advanced ...........................................................................................................................305.7
5.7.1 Device Status..........................................................................................................30
5.7.2 Wireless..................................................................................................................34
5.7.3 Network...................................................................................................................39
5.7.4 Firewall....................................................................................................................45
5.7.5 Management...........................................................................................................48
Chapter 6.Quick Connection to a Wireless Network.......................................................................55
Windows XP (Wireless Zero Configuration)...................................................................556.1
Windows 7 (WLAN AutoConfig).......................................................................................576.2
Mac OS X 10.x....................................................................................................................606.3

IV
iPhone/iPod Touch/iPad ...................................................................................................646.4
Appendix A: Planet Smart Discovery Utility.....................................................................................67
Appendix B: FAQs...............................................................................................................................68
Q1: How to set up the AP Client Connection...........................................................................68
Q2: How to set up the WDS Connection..................................................................................72
Appendix B: Troubleshooting............................................................................................................78
Appendix C: Glossary.........................................................................................................................80

V
FIGURE
FIGURE 2-1 WBS-202N/502N FRONT SIDE.............................................................................................10
FIGURE 2-2 WBS-202N/502N REAR SIDE...............................................................................................10
FIGURE 2-3 WBS-202N RIGHT SIDE........................................................................................................11
FIGURE 2-4 WBS-502N RIGHT SIDE........................................................................................................11
FIGURE 2-5 WBS-202N/WBS-502N INTERFACE......................................................................................12
FIGURE 3-1 CONNECT THE ANTENNA........................................................................................................13
FIGURE 3-2 CONNECT THE ETHERNET CABLE............................................................................................14
FIGURE 3-3 CONNECT THE POEINJECTOR................................................................................................14
FIGURE 4-1 TCP/IPSETTING...................................................................................................................16
FIGURE 4-2WINDOWS START MENU ........................................................................................................17
FIGURE 4-3 SUCCESSFUL RESULT OF PING COMMAND..............................................................................17
FIGURE 4-4 FAILED RESULT OF PING COMMAND .......................................................................................18
FIGURE 4-5 LOGIN BY DEFAULT IPADDRESS.............................................................................................19
FIGURE 4-6 LOGIN WINDOW.....................................................................................................................19
FIGURE 5-1 MAIN MENU ..........................................................................................................................20
FIGURE 5-2 OPERATION MODE.................................................................................................................21
FIGURE 5-3 GATEWAY MODE....................................................................................................................21
FIGURE 5-4 GATEWAY-STATIC IP .............................................................................................................22
FIGURE 5-5 GATEWAY –PPPOE(ADSL)..................................................................................................22
FIGURE 5-6 GATEWAY –DHCP................................................................................................................23
FIGURE 5-7 GATEWAY –WIRELESS ..........................................................................................................23
FIGURE 5-8 REPEATER MODE ..................................................................................................................24
FIGURE 5-9 REPEATER MODE -SCAN AP .................................................................................................25
FIGURE 5-10 REPEATER MODE -SELECTAP............................................................................................25
FIGURE 5-11 WISPMODE.......................................................................................................................26
FIGURE 5-12 WISP MODE –SELECTAP..................................................................................................26
FIGURE 5-13 WISP MODE –SELECT WAN TYPE......................................................................................27
FIGURE 5-14APMODE ...........................................................................................................................27
FIGURE 5-15 SUPER WDS MODE ............................................................................................................28
FIGURE 5-16 SUPER WDS MODE –AP1..................................................................................................29
FIGURE 5-17 SUPER WDS MODE –AP2..................................................................................................29
FIGURE 5-18 ADVANCED..........................................................................................................................30
FIGURE 5-19 STATUS...............................................................................................................................30
FIGURE 5-20 WIRELESS STATUS ..............................................................................................................31
FIGURE 5-21 LAN STATUS.......................................................................................................................32
FIGURE 5-22 WAN STATUS......................................................................................................................33
FIGURE 5-23 BASIC SETTINGS .................................................................................................................34
FIGURE 5-24 VIRTUAL AP........................................................................................................................35
FIGURE 5-25ACCESS CONTROL -ACCESS ALL .........................................................................................35
FIGURE 5-26ACCESS CONTROL –ALLOW LISTED.....................................................................................36
FIGURE 5-27ADVANCED SETTINGS ..........................................................................................................37
FIGURE 5-28 LAN SETTINGS ...................................................................................................................39

VI
FIGURE 5-29 IP-MAC BIND .....................................................................................................................39
FIGURE 5-30 VLAN.................................................................................................................................40
FIGURE 5-31 SNMP................................................................................................................................41
FIGURE 5-32 STATIC IP............................................................................................................................41
FIGURE 5-33 PPPOE(ADSL)..................................................................................................................42
FIGURE 5-34 DHCP................................................................................................................................43
FIGURE 5-35 WANADVANCED SETTINGS..................................................................................................44
FIGURE 5-36 IP/PORT FILTERING.............................................................................................................45
FIGURE 5-37 MAC FILTERING..................................................................................................................46
FIGURE 5-38 URLFILTERING...................................................................................................................46
FIGURE 5-39 PORT FORWARDING.............................................................................................................47
FIGURE 5-40 DMZ ..................................................................................................................................48
FIGURE 5-41 SYSTEM TIME......................................................................................................................48
FIGURE 5-42 SIGNAL TRACKING ...............................................................................................................49
FIGURE 5-43 DDNS SETTINGS.................................................................................................................50
FIGURE 5-44 QOS...................................................................................................................................51
FIGURE 5-45 LOGS..................................................................................................................................52
FIGURE 5-46 UPGRADE FIRMWARE ..........................................................................................................53
FIGURE 5-47 SYSTEM..............................................................................................................................53
FIGURE 5-48 USER..................................................................................................................................54
FIGURE 6-1 SYSTEM TRAY –WIRELESS NETWORK ICON ...........................................................................55
FIGURE 6-2 CHOOSING A WIRELESS NETWORK.........................................................................................55
FIGURE 6-3 ENTERING THE NETWORK KEY...............................................................................................56
FIGURE 6-4 CHOOSING A WIRELESS NETWORK -- CONNECTED..................................................................56
FIGURE 6-5 NETWORK ICON.....................................................................................................................57
FIGURE 6-6 WLANAUTOCONFIG.............................................................................................................57
FIGURE 6-7 TYPING THE NETWORK KEY ...................................................................................................58
FIGURE 6-8 CONNECTING TO A NETWORK.................................................................................................58
FIGURE 6-9 CONNECTED TO A NETWORK ..................................................................................................59
FIGURE 6-10 MAC OS –NETWORK ICON..................................................................................................60
FIGURE 6-11 HIGHLIGHTING AND SELECTING THE WIRELESS NETWORK .....................................................60
FIGURE 6-12 ENTER THE PASSWORD .......................................................................................................61
FIGURE 6-13 CONNECTED TO THE NETWORK............................................................................................61
FIGURE 6-14 SYSTEM PREFERENCES.......................................................................................................62
FIGURE 6-15 SYSTEM PREFERENCES -- NETWORK ...................................................................................62
FIGURE 6-16 SELECTING THE WIRELESS NETWORK ..................................................................................63
FIGURE 6-17 IPHONE –SETTINGS ICON....................................................................................................64
FIGURE 6-18 WI-FI SETTING....................................................................................................................64
FIGURE 6-19 WI-FI SETTING –NOT CONNECTED......................................................................................65
FIGURE 6-20 TURNING ON WI-FI..............................................................................................................65
FIGURE 6-21 IPHONE -- ENTERING THE PASSWORD...................................................................................66
FIGURE 6-22 IPHONE -- CONNECTED TO THE NETWORK ............................................................................66

User Manual of WBS-202N/WBS-502N
-1-
Chapter 1. Product Introduction
Package Contents1.1
Thank you for choosing PLANET WBS-202N or WBS-502Ne Wireless AP. Please verify the contents inside the
package box.
Package Contents of WBS-202N/WBS-502N
WBS-202N / WBS-502N Quick Guide Ethernet Cable Mounting Strap
If there is any item missing or damaged, please contact the seller immediately.

User Manual of WBS-202N/WBS-502N
-2-
Product Description1.2
Flexible and Reliable Outdoor Characteristics
With the standard IEEE 802.3af/at Power over Ethernet (PoE) design, the WBS-202N and WBS-502N (outdoor
wireless CPE) can be easily installed in the areas where power outlets are not available. The outdoor wireless
CPE is definitely suitable for wireless IP surveillance, and bridge link of building to building and backbone of
public service. Additionally, the self-healing capability keeps connection alive all the time. With the IP55-rated
outdoor enclosure, the outdoor wireless CPE can perform normally under rigorous weather conditions, meaning
it can be installed in any harsh, outdoor environments
Designed for Various Requirements
The outdoor wireless CPE is specially designed for long-distance outdoor surveillance and wireless backhaul
solutions that are capable of establishing stable bridge connection through the embedded antenna. To provide
maximum performance, the outdoor wireless CPE can implement up to 8 operation modes where a multitude of
applications in communities, warehouses, campuses, harbors, etc. can be made.

User Manual of WBS-202N/WBS-502N
-3-

User Manual of WBS-202N/WBS-502N
-4-
Multiple SSIDs with VLAN Tagging
The outdoor wireless CPE supports WPA/WPA2, and the 802.1X RADIUS authentication to secure the wireless
connection. Besides, the supported IEEE 802.1Q VLAN allows multiple VLAN tags to be mapped to multiple
SSIDs to distinguish the wireless access. This makes it possible for the outdoor wireless CPE to work with
managed Ethernet switches to have VLANs assigned to a different access level and authority.
3 Simple Steps to Set Up WDS
Without needing to enter the Web interface for configuration, the outdoor wireless CPE needs three simple steps
to establish the WDS PtP connection without any difficulty. By just clicking the Pair button on the WBS-202N and
within 2 minutes, you can connect two WBS-202Ns without complicated configuration.

User Manual of WBS-202N/WBS-502N
-5-
Optimized Efficiency in AP Management
The brand-new GUI configuration wizard helps the system administrator easily set up the outdoor wireless CPE
step by step. Besides, the built-in Wi-Fi analyzer provides real-time channel utilization to prevent channel
overlapping to assure greater performance. With the automatic transmission power mechanism, distance control
and scheduling reboot setting, the outdoor wireless CPE is easier for the administrator to deploy and manage
without on-site maintenance. Moreover, you can simply use PLANET AP controller and SAPC (Smart AP
Control), to deliver wireless profiles to multiple APs simultaneously, thus making the central management
simple.

User Manual of WBS-202N/WBS-502N
-6-
Product Features1.3
Industrial Compliant Wireless LAN and LAN
Compliant with the IEEE 802.11b/g/n and IEEE 802.11a/n wireless technology
2T2R architecture with data rate of up to 300Mbps
Equipped with two 10/100Mbps RJ45 ports with auto MDI/MDI-X supported
Fixed Network Broadband Router
Supported WAN connection types: DHCP, Static IP, PPPoE
Supports Port Forwarding and DMZ for various networking applications
Supports DHCP server in Gateway/WISP mode
RF Interface Characteristics
Built-in 14dBi dual-polarization antenna (WBS-202N)
Built-in 15dBi dual-polarization antenna (WBS-502N)
High output power with multiply-adjustable transmit power control
Outdoor Environmental Characteristics
IP55 rating
IEEE 802.3af/at Power over Ethernet design
Operating temperature: -20~70 degrees C
Multiple Operation Modes and Wireless Features
Multiple operation modes: AP, Gateway, Repeater, WDS, WISP
WMM (Wi-Fi multimedia) provides higher priority to multimedia transmitting over wireless
Coverage threshold to limit the weak signal of clients occupying session
Real-time Wi-Fi channel analysis chart and client limit control for better performance
Secure Network Connection
Full encryption supported: WPA/WPA2, WPA-PSK/WPA2-PSK and 802.1X RADIUS authentication
Supports 802.1Q VLAN and SSID-to-VLAN mapping
Supports IP/Port/MAC address/URL filtering, DoS, SPI Firewall
Supports DMZ and Port Forwarding
Bandwidth control per IP address to increase network stability
Easy Installation and Management
3 simple steps to establish WDS connection easily
Supports PLANET AP Controllers in AP mode
Easy discovery by PLANET Smart Discovery
Self-healing mechanism through system auto reboot setting
System status monitoring through remote Syslog Server
Supports PLANET DDNS/ Easy DDNS

User Manual of WBS-202N/WBS-502N
-7-
Product Specifications1.4
Model Name WBS-202N WBS-502N
Description WBS-202N: 2.4GHz 802.11n 300Mbps Outdoor Wireless CPE
WBS-502N: 5GHz 802.11n 300Mbps Outdoor Wireless CPE
Hardware Features
Interfaces
Wireless IEEE802.11b/g/n, 2T2R Wireless IEEE 802.11a/n, 2T2R
PoE: 1 x 10/100BASE-TX, auto-MDI/MDIX, 802.3af/at PoE In
LAN: 1x 10/100BASE-TX, auto-MDI/MDIX
Antennas Built-in 14dBi directional
antenna with
dual polarization
Built-in 15dBi
directional antenna with dual
polarization
Button Reset/Pair button, WDS Switch
Dimensions 87 x 38 x 260mm
Weight 405g
Power Requirements 48V 0.5A, IEEE 802.3af/at PoE+
Power Consumption < 13W
Wireless Interface Specifications
Standard
IEEE 802.11b/g/n
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x flow control
IEEE 802.11a/n
IEEE 802.11i
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3x flow control
Media Access Control CSMA/CA
Modulation
802.11g/n: OFDM (BPSK/ QPSK/
16QAM/ 64QAM)
802.11b: DSSS (DBPSK/ DQPSK/
CCK)
802.11a/n:
OFDM (BPSK/ QPSK/ 16QAM/
64QAM)
Frequency Band FCC: 2.412~2.462GHz
ETSI: 2.412~2.472GHz FCC: 5.180~5.240GHz, 5.745~5.825GHz ETSI: 5.180~5.700GHz
Operating Channels FCC: 1~11 Channels
ETSI: 1~13 Channels
FCC: 36, 40, 44, 48, 149, 153, 157, 161,
165 (9 channels)
ETSI: 36, 40, 44, 48, 52, 56, 60, 64, 100,
104, 108, 112, 116, 132, 136, 140 (16
channels)
5GHz channel list will vary in different
countries according to their
regulations.
Max. Transmit Power
(dBm) FCC: up to 29 ± 1dBm
ETSI: < 20dBm (EIRP) FCC: up to 27 ± 2dBm ETSI: < 20dBm (EIRP)
Network
Mode Data Rate
Receive
Sensitivity
(dBm)
Network
Mode Data Rate
Receive
Sensitivity
(dBm)

User Manual of WBS-202N/WBS-502N
-8-
802.11b 1Mbps -95
11Mbps -90
802.11g 6Mbps -90 802.11a 6Mbps -92
54Mbps -72 54Mbps -75
802.11n
HT20
MCS0/MCS
8 -90 802.11n
HT20
MCS0/MC
S8 -91
MCS7/MCS
15 -72/-68 MCS7/MC S15 -72
802.11n
HT40
MCS0/MCS
8 -90 802.11n
HT40
MCS0/MC
S8 -88
MCS7/MCS
15 -72/-68 MCS7/MC S15 -70
Environment & Certification
Operating Temperature -20 ~ 70 degrees C
Operating Humidity 5 ~ 90% (non-condensing)
IP Level IP55
ESD Protection ± 8kV air-gap discharge
± 4kV contact discharge
Surge Protection ± 4kV
Regulatory CE, RoHS
Software
LAN Static IP
Supports IP-MAC binding
WAN Type (GW/WISP
mode)
Static IP
Dynamic IP
PPPoE
Wireless Modes
Access Point
Gateway
Repeater
WDS (AP/Bridge/Station)
WISP
Channel Width 20MHz, 40MHz
Encryption Type WPA, WPA-PSK, WPA2, WPA2-PSK, 802.1X
Wireless Security Enable/Disable SSID Broadcast
Wireless MAC address filtering
User Isolation
Max. SSIDs 4

User Manual of WBS-202N/WBS-502N
-9-
Max. Wireless Clients 64 per radio (50 is suggested, depending on usage)
Max. WDS Peers 4 (Up to 3 peers by using “One-click WDS”)
Wireless QoS Supports Wi-Fi Multimedia (WMM)
Wireless Advanced
Auto Channel Selection
5-level Transmit Power Control (100%, 75%, 50%, 25%, 12.5%)
Client Limit Control, Coverage Threshold
Distance control (Auto Ack Timeout)
Wi-Fi channel analysis chart
Status Monitoring
Device status, wireless client List
PLANET Smart Discovery
DHCP client table
System Log supports remote syslog server
VLAN IEEE 802.1Q VLAN (VID: 3~4094)
SSID-to-VLAN mapping up to 4 SSIDs
Self-healing Supports auto reboot settings per day/hour
Management
Remote management through PLANET DDNS/ Easy DDNS
Configuration backup and restore
Supports UPnP
Supports IGMP Proxy
Supports PPTP/L2TP/IPSec VPN Pass-through
SNMP v1/v2c/v3 support, MIB I/II, Private MIB
Central Management Applicable controllers: WAPC-500, WAPC-1000 and Smart AP Control(SAPC)

User Manual of WBS-202N/WBS-502N
-10-
Chapter 2. Hardware Installation
Product Outlook2.1
WBS-202N/502N
Dimensions: 87 x 38 x 260mm
Front Side :
Figure 2-1 WBS-202N/502N Front Side
Rear Side
Figure 2-2 WBS-202N/502N Rear Side

User Manual of WBS-202N/WBS-502N
-11-
RightSide
Figure 2-3 WBS-202N Right Side
Figure 2-4 WBS-502N Right Side
LED Definition
LED State Meaning
Power On The device is powered on
Off The device is powered off
WAN Port
On Port linked
Blinking Data is transmitting or receiving data
Off No link
LAN Port
On Port linked
Blinking Data is transmitting or receiving data
Off No link
WLAN
On The wireless radio is on
Blinking Data is transmitting or receiving over wireless
Off The wireless radio is off

User Manual of WBS-202N/WBS-502N
-12-
2.1.1 Port and Button
It provides a simple interface monitoring the AP. Figure 2-5 shows the hardware interface of the
WBS-202N/502N.
WBS-202N/502N Hardware Interface:
Figure 2-5 WBS-202N/WBS-502N Interface
2.1.2 Hardware Description
Hardware Interface Definition
Object Description
PoE LAN Port
10/100Mbps RJ45 port, auto MDI/MDI-X
LAN Port 10/100Mbps RJ45 port, auto MDI/MDI-X
WDS Switch Position “S” to “M” on the master AP. Stay in “S” on the slave AP.
Reset/Pair Button
Press and hold the Reset button on the device for over 15 seconds to
return to the factory default setting.
Press the Pair button within 2 minutes on both sides to establish WDS
PtP connection.