Planmeca ProOne Use and care manual

ProOne
PLANMECA
Calibration
Manual
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

2
The manufacturer, assembler, and importer are responsible for the safety,
reliability and performance of the unit only if:
- Installation, calibration, modification and repairs are carried out by
qualified authorized personnel.
- Electrical installations are carried out according to the appropriate
requirements such as IEC364.
- Equipment is used according to the operating instructions
Planmeca pursues a policy of continual product development. Although every
effort is made to produce up-to-date product documentation this publication
should not be regarded as an infallible guide to current specifications. We
reserve the right to make changes without prior notice.
COPYRIGHT PLANMECA USA 2008-03
PUBLICATION Revision 2 JO
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

3
Table of Contents
Chapter A: General Information
1. Disclaimer 5
2. Required Tools 7
2.1 Calibration Tools 7
2.2 Hand Tools 8
Chapter B: Pre-check
1. Dimaxis 4.3.x 9
2. Ball Phantom Test 9
2.1 Measurement Tool Calibration 10
2.2 Measuring Image 10
Chapter C: Removing Covers
1. Upper Arm 13
2. Sensor Head 13
3. Inner Tubehead 14
4. Inner C-Arm 15
Chapter D: Alignment
1. Beam Adjustment 17
1.1 Vertical Alignment 19
1.1.a. High/Low 19
1.1.b Angled 19
1.2 Horizontal Alignment 20
1.2.a Left/Right 20
2. Ball Phantom y-line 21
2.1 Adjusting Y-line 23
3. Ball Phantom x-line 24
3.1 Adjusting X-line 26
3.2 Checking the symmetry 27
3.2.a More than 1mm deviation 28
4. Positioning Lights 29
4.1 Layer 29
4.1.a Adjusting the light 31
4.2 Midsagittal 32
4.3 Frankfort 32
4.3.a Adjusting the light 33
Chapter E: Calibrating the sensor
1. ProOne Setup 35
2. Computer Setup 36
3. Calibration File creation 37
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

4
Chapter F: Ball Phantom
1. Dimaxis 4.3.x 39
2. Measurement Tool Calibration 40
3. Measuring the Image 40
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

5
Chapter
A General Information
1 DISCLAIMER
This manual contains the information required to setup and calibrate
the Planmeca ProOne Panoramic unit.
WARNING :
Protect yourself from radiation when you are checking the beam
alignment and calibrating. Since radiation safety requirements vary
from state to state, country to country, it is the responsibility of the
installer to ensure that the correct precautions are observed.
1.1 The display values shown in this guide are only examples
and should be interpreted as recommended values unless
otherwise specified.
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

6
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

7
2 REQUIRED TOOLS
2.1. Calibration Tools
 Ball phantom (part number 50977) used for checking the position of the
Patient Positioning Mechanism and the Positioning lights. (Figure 1)
Figure 1
 Frankfort plane alignment tool (part number 50977) used with the ball
phantom for checking the position of the Frankfort plane light. (Figure
2)
Figure 2
 Beam alignment tool, fluorescent screen, (part number 50972) used for
checking the position of the x-ray beam. (Figure 3)
Figure 3
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

8
 Alignment Ruler (part number 50973) used for checking the alignment
of the patient positioning mechanism. (Figure 4)
Figure 4
 Calibration block (part number 10016995) used for calibrating the
sensor. (Figure 5)
Figure 5
 Alignment Pins (part number 7100) used for locking the c-arm into
positioning for checking alignment. (Figure 6)
Figure 6
2.2 Hand Tools
 2.5 mm allen wrench
 4 mm allen wrench
 Needle Nose Pliers
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

9
Chapter
B Pre-Check
1 Dimaxis 4.3.x
Click on Start, All Programs, Planmeca, Dimaxis 4.3.x
NOTE: Place the ball phantom into the patient positioning mechanism.
2 Ball Phantom Test
Click OK then click OK again. Select “New” from the bottom of the “Select
Image” screen.
Press the exposure button then press OK once the image is taken to evaluate the
image.
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018

10
2.1 Measurement Tool Calibration
Click the measurement toolbar at the top. (Figure 7)
Figure 7
Click on the first icon, CAL, and calibrate the Center Ball from top to
bottom. (Figure 8)
Figure 8
Enter the number 7 when asked to input a distance. (Figure 9)
Figure 9
2.2 Measuring Image
Click the second icon now and measure the Center Ball top to bottom and
left to right. (Figure 10)
Figure 10
The ball should be 7mm top to bottom and left to right. (Figure 11)
Figure 11
Printed copies of this document are considered uncontrolled.
7535.11.Rev001 08.07.2018