POSIFLEX XT-5315 User manual

Package Contents
15” P-CAP touch terminal with Gen 7E or
Gen 8E base (x 1)
Power adapter (x 1)
Power cord (x 1)
User manual (x 1)
Product Features
Fanless Design
Intel 4th generation Haswell CPU
New Gen 7E foldable base that allows JIVA XT Series to be configured
into different configurations.
New Gen 8E foldable base that integrates internal power adaptor and
Powered USB port into the base.
Mini-PCIe expansion slot
16760900020 Ver. A0
http://www.posiflex.com
XT-5315/5515/5515Pro
P-CAP Touch Terminal
User Manual
1

Views of XT-5315/5515/5515Pro with Gen 7E Base
Front View
Rear View
Side View
Cable Cover
Neck Cover
HDD Cover
Cable Exit
XT-5315/5515/5515Pro
P-CAP Touch Panel
LED indicator
Power Button
Brightness Adjustment Button
＋
Brightness Adjustment Button －
Gen 7E Base
2

Bottom View
Views of XT-5315/5515/5515Pro with Gen 8E Base
Front View
Rear View
Cable Holder
Cable Exit
XT-5315/5515 /5515Pro
P-CAP Touch Panel
HDD Cover
Cable Cover
Neck Cover
Cable Exit
LED indicator
Rubber Feet with Fixing Screw
Rubber Feet with Fixing Screw
Gen 8E Base
3

Side View
Bottom View
View of I/O Interface of XT-5315/5515
Rubber Feet with Fixing Screw
Line Out/MIC-In
Combo Jack
USB 2.0
Ports
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Ports
12V BAT Port
DC IN
Power
Connector
Rubber Feet with Fixing Screw
RJ-50 COM Ports
UPS Battery
Compartment
Power Adapter
Compartment
PoweredUSB
Compartment
HD Compartment
Power Button
Brightness Adjustment Button
＋
Brightness Adjustment Button －
4

View of I/O Interface of XT-5515Pro
Positioning your POS for a Perfect Viewing Angle
The adjustable bases designed for XT-5315/5515/5515Pro come in two models,
Gen 7E/8E, and allow you to determine an ideal position for your terminal
using its unique tilt adjustment mechanism. As the below figures suggest, both
bases provide three standard positioning solutions for your terminal: Flat
Folded mode, Low Profile mode, and Full Extended mode.
XT-3515/5515/5515Pro with Gen 7E Base
Flat Folded mode
Low Profile mode
Full Extended mode
XT-3515/5515/5515Pro with Gen 8E Base
Flat Folded mode
Low Profile mode
Full Extended mode
Line Out/MIC-In
Combo Jack
USB 3.0
Ports
DB9 COM Ports
VGA Port
CR Port
LAN Port
12V BAT Port
DC IN
Power
Connector
RJ-50 COM Ports
HDMI Port
5

In general, XT-5315/5515/5515Pro will be set up beforehand in Flat Folded
mode and then packaged into the box for shipping. After it is unpacked, you
may re-adjust the terminal in either Low Profile mode or Full Extended mode
according to your situation. Below will provide instructions on how to adjust
the specific base connected to the POS system. As a reminder, please be
careful not to touch the LCD panel while setting up the tilt angle.
XT-3515/5515/5515Pro with Gen 7E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 7E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out of
the package box and then lay your POS
system on a flat surface.
2. Steady the base with one hand, and then tilt
the screen downwards.
3. Position your terminal in Full Extended mode
3.1 After grabbing the bottom edge of the screen with your hand, gently
move the screen upward until the screen is locked into place with a
click sound.
3.2 With the screen facing toward you, tilt the
screen up or down to your desired angle.
Please do not press on the LCD panel while
setting up the tilt angle.
6

4. Return your terminal back to Flat Folded mode from Full Extended
mode.
4.1 Tilt your screen in a horizontal position. Then, remove the cable
cover from the base.
4.2 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, move the display downwards
until the lever is lifted off the hook as shown in the figure
4.3 Push the cable cover back.
4.4 Tilt the screen again to the horizontal
position.
Hook
Lever
7

5. Position the terminal in Low Profile mode.
5.1 Follow Step 4 to set up the termimal in Flat
Folded mode.
5.2 Tilt the screen all the way down
5.3 To tilt screen up or down to your desired
angle, please be advised to keep the base
steady with one hand to do so. Do NOT
press on the LCD panel while setting up the
tilt angle.
XT-5315/5515/5515Pro with Gen 8E Base
Please refer to the following instructions on how to switch among different
positioning modes to find an ideal viewing angle for XT-5315/5515/5515Pro
with Gen 8E base.
1. Unpack XT-5315/5515/5515Pro, which is
supposed to be set in flat folded mode, out
of the package box and then lay your POS
system on a flat surface.
2. While steadying the terminal with your
hand holding onto the base, tilt the screen
down.
8

3. Push the cable cover outwards to remove
it from the base.
4. Position your terminal in Full Extended mode.
4.1 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display upwards
until the lever is snapped into the lower hook to raise the screen as
shown in the below figure.
4.2 Push the cable cover back.
4.3 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the tilt
angle.
Lower
hook
Lever
9

5. Position the terminal in Low Profile mode.
5.1 While keeping your terminal steady with your hand holding on to
the base, tilt your terminal down. Then, remove the cable cover
from the base.
5.2 Support the screen with one hand holding onto its bottom edge.
Then, while pulling the lever backwards, move the display
upwards or downwards until the lever is snapped into the upper
hook to lower the screen as shown in the below figure.
5.3 Push the cable cover back.
5.4 Tilt the screen up or down to your
desired angle. Please do not press on
the LCD panel while setting up the
tilt angle.
Lever
Upper
hook
10

6. Return the terminal back to Flat Folded mode.
6.1 While steadying your terminal with your hand holding onto the
base, tilt your screen up.
6.2 Support the screen with one hand holding onto its bottom edge.
While pulling the lever backwards, release the lever back to the
point above the upper hook as shown in the figure.
6.3 Push the cable cover back.
6.4 Tilt the screen to the horizontal position.
Lever
11

Routing and Arranging Cables
Gen 7E/8E bases feature their own cable management to help you well
organize the cords whenever you need to connect peripheral devices to XT-
5315/5515/5515Pro. The following provides some useful cable-routing
instructions required to manage your cables.
1. Set up your terminal in Full Extended
mode and then tilt the screen all the way
down.
2. Remove the cable cover.
3. Pull outwards the locking levers with your
forefingers and then remove the neck
cover in the direction shown by the arrow.
4. Tilt the screen to the horizontal position.
Thread the cables along the cable passage
and then through the cable exit.
5. Tilt the terminal up enough to have the bottom I/O plate
towards you. Locate the cable arrangement cover as shown in
the figure.
Cable Arrangement Cover
12

6. Remove the cable arrangement cover by
pushing it up in the direction shown by
the arrow.
7. Properly insert the cable into the correct
port on the bottom I/O plate.
8. Neatly arrange your cable. Then, make
sure the cord can be held into place and
passed through the cable exit after sliding
back the cable arrangement cover.
9. Have the screen tilt all the way down, and
then push the neck cover back into place.
10. Place the cable cover back.
11. Make sure the cable is threaded through the cable exit at the bottom
of the base.
Gen 7E base
Gen 8E base
Cable Exit
13

Installing Optional Upgrade Kits and Peripherals
XT-5315/5515/5515Pro is an expandable model which allows you to upgrade
its own capacity by additionally installing multiple peripheral devices, such as
magnetic stripe reader (MSR), LCD monitor and cash drawer, according to
your preference. The following will give you installation instructions on how
to expand on your current POS system with these optional upgrade kits. Before
proceeding with the installation of peripherals, please make sure the POS
system is completely shut down to prevent damage.
Installing UPS Battery to Gen 8E Base
UPS battery compartment can be found at
the bottom of Gen 8E base as shown in the
figure. Please be advised that the installation
of UPS battery should be conducted by a
technician according to the user manual
specific to UPS battery.
Installing PoweredUSB to Gen 8E Base
The middle compartment at the bottom of
Gen 8E base is designed to install
PoweredUSB. However, the installation of
PoweredUSB is required to be conducted
properly and accurately, so please contact
your service provider for help. The detailed
installation guide will be provided in the
relevant technical manual.
Installing Power Adapter to Gen 8E Base
Power adapter is used to provide power which your terminal needs to be
operated normally. Please go through the below steps to install the power
adapter into Gen 8E base. If the power adapter is already installed to Gen
8E base, you may skip this section
1. Lay your POS terminal on a flat surface
with its bottom facing towards you.
14

2. Take the AC power adapter with its
rubber feet facing you. Place the bottom
side of the power adapter into the
bottom of the power adapter
compartment first, and then push the top
side of the adaptor into the
compartment.
3. After pushing the power adapter up to
the top, place two brackets separately on
the top and bottom sides of the power
adapter compartment as shown in the
figure. Then, fasten two brackets with
four fixing screws.
4. Before threading the cable through the cable exit, loosen two
fixing screws for the bracket of the PoweredUSB compartment.
Then, slide the bracket in the direction shown by the arrow to
remove the bracket.
5. Pass the cable of the power adapter
through the cable exit and then connect
it to the port on the I/O plate of your
POS system. (Please refer to Routing
and Arranging Cables section to thread
the cable, according to the model of
your base.)
Cable Exit
Bracket Power Adaptor
15

6. Neatly thread the cord along the bottom edge of the PoweredUSB
compartment (1), and then use the cable tie to hold the extra cable
(2) as shown in the figure.
7. Place back the PoweredUSB
compartment bracket into place, and
then secure it using two fixing screws.
8. Lay the POS terminal on a flat surface
with its rear facing towards you. Then,
connect the female end of power cord to
the power adapter and the other end to
the electrical outlet.
9. To hold the power cord into place, attach the screw hole of
power cord holder to the hole at the bottom of Gen 8E base,
and then use a fixing screw to secure the power cord holder.
Cable tie
(1)
(2)
Power Cord Holder
16

Installing Side Mount Upgrade Kits
Located at left side on the back of
your LCD panel, side mount
compartment is mainly used for
installation of side-mounted
equipment, such as magnetic stripe
reader. For detailed installation
instructions, please refer to the user
manual specific to the device which
you intend to mount onto the terminal.
Installing Rear Top Mount Upgrade Kits
Rear top mount upgrade kits, including
customer pole displays and monitors,
have to be mounted onto the top side on
the rear of your POS terminal as shown
in the figure. As for the installation
instructions along with the individual
cable arrangement for the specific base,
please be advised to read the user
manual specific to the device you
intend to install.
Installing Wall Mount Kits
The wall mount kits enable you to mount your POS terminal onto the
wall as an alternative. For detailed installation instructions, please be
advised to refer to the user manual specific to wall mount kits.
Installing an Operating System
You are highly advised not to install an operating system on XT-
5315/5515/5515Pro without professional instructions. Not only might the
careless handling during installation cause irreversible damage to your
machine, but also the improper installation likely leads to system malfunction
or failure. Please contact with your dealers about the issues of operating
system installation.
Performing System Recovery
For XT-5315/5515/5515Pro models with preloaded operating systems, you are
not encouraged to recover your system without the help of system integrators.
Please be advised to contact your service center for further assistance with
system recovery.
17

Operation Environment
To prevent XT-5315/5515/5515Pro from overheating, it is suggested to
position your terminal in a well-ventilated working environment. In doing so,
please be advised to keep the POS terminal at least 25mm away from other
devices to ensure the machine is properly cooled down and functioning
normally.
Powering ON/OFF XT-5315/5515/5515Pro
Power ON XT-5315/5515/5515Pro
Press down the power button for at least 3 seconds
to power on the POS.
Power OFF XT-5315/5515/5515Pro
In most cases, press the power button of the POS to
power the system off. If the terminal fails to turn
off the machine for unknown reasons, please be
advised to hold the power button more than 10
seconds to force a shutdown of the system.
Status LED Indicator
LED status indicator, which is located at the bottom edge of the LCD panel, is
mainly responsible for notifying users of the current system status by emitting
various LED signals. In the chart provided below, it describes all the possible
LED status as a quick reference.
LED Status
System
status
AC power
supply
UPS Battery
Description
Off
OFF
OFF
Without battery
System power OFF
Off
OFF
OFF
With battery
System power OFF
Green
OFF
ON
With/Without
battery
System standby
Blue
ON
ON
With/Without
battery
System power ON
Blinking blue
ON
OFF
With battery
System running on
UPS battery
Blinking green
ON
OFF
With battery
UPS battery low
Power
Button
18

Specifications
XT-5315
XT-5515
XT-5515Pro
CPU
Intel Haswell CPU, LGA 1150 Package
DRAM Memory
SO-DIMM socket x2, DDR-3 1600, Max. 16GB
Storage Device
SATAIII x2 (2.5" HDD)
RAID Function
N/A
RAID0, RAID1
Intel vPro support
N/A
Yes
TPM Function
N/A
Yes
Power Supply
12V/130W (upgrades to 12V/150W for PoweredUSB)
OS Support
POSReady 7 / Win 7 / Linux / Win8 / Win 10 IoT
LCD Display
15" TFT LCD, 1024 x 768
Touch Function
5 wires, bezel-free P-CAP touch panel
Serial Port
Max. 6 ports, DB9 x2, RJ45 x2 (RJ-45 to DB9 Cable
Optional), Box-Header x1 (Y cable to DB9 x2 Optional)
Parallel Port
1 port, Box-header x1 on back window (Optional)
HDMI Port
N/A
1 port
Display Port
1 port, Box-header x1
N/A
Standard USB
Port
8 ports, 6ports on the Rear I/O
(USB3.0 x 2 & USB2.0 x 4), 2
internal proprietary ports for
extension device
8 ports, 6ports on the
Rear I/O (USB3.0 x
6), 2 internal
proprietary ports for
extension device
PoweredUSB
(Optional)
PU-480：24V x 1 + 5V x 8 via Gen 8E base
PU-490
：
24V x 1 + 12V x 3 via Gen 8E base
LAN Port
2 ports, 10 / 100 / 1000 Mb x 2
1 port, 10/100/1000
Mb x1 (Intel i217LM
only)
VGA Port
1 port, D-SUB 15 Pin with 12V power for Posiflex LCD
Monitor
CR Port
1 port, controlling 2 CR
PS/2 Keyboard
1 port, Box-header x1 on back window
UPS Port
Yes, optional 2300mAh/12V Battery
Audio Port
Mic-in / Line-Out for Combo Jack
Extension Slot
mini-PCIe slot x 1, USB interface support
Power Indicator
LED
Power On/Standby, bi-color LED indicators
Ethernet link LED on Ethernet connector
Wireless LAN
Optional, through mini-PCIe slot
Dimension
372 x 320 x 252.7 (W x D x H in mm)
Weight
5.86 (N. W. in kg)
Environmental
Requirements
Operating
：
0°C
〜
40°C, 20%RH - 90%RH (Equipped with
HDD);0°C 〜50°C, 20%RH - 90%RH (Equipped with SSD)
Storage：-20°C 〜70°C, 10%RH - 90%RH
19

<MEMO>
20