POSIFLEX PS-3315 User manual

1
Package Contents
PS-3315/3315E/3316/3316E fanless
LCD touch terminal (x 1)
12V/40W Power adaptor (x 1)
Power cord (x 1)
User Manual (x 1)
Product Features
Fanless terminal
Foldable base that allows PS Series to be configured into different
configurations
5-wire resistive touch for PS-3315/3315E/3316/3316E
Integrated structure for side mount upgrade kit: SA-
105/205/305/405/505; back mount display: LM-6807U / 6810U and
PD-360R/360UE/2609UE/6807U; 40-key dynakey attachment with
MSR or RFID option: KP-500
Water resistant structure designed for easy cleaning
PS-3315/3315E/3316/3316E
Fanless LCD Touch Terminal
User Manual
13110900070 Ver. F0

2
Views of PS-3315/3315E/3316/3316E
Front View
PS-3315/3315E
PS-3316/3316E
Rear View
PS-3315/3315E
PS-3316/3316E
Left Side View
LCD Touch Panel
Gen7 Base
MSR Port Cover
HDD Cover
HDD Cover
Rear I/O Cover
Rear I/O Cover
Neck Cover
Cable Cover
Cable Exit
2nd Display
Screw Hole

3
Right Side View
Bottom View
View of I/O Interface
Top I/O Ports
Rear I/O Ports
1
COM4 Port
3
Parallel (LPT) Port Connector
2
USB 2.0 Port
4
PS/2_KB Pin Header
Bottom I/O Cover
1
2
3
4
Power Button
Brightness
Adjustment Button “+”
Brightness
Adjustment Button “-”

4
Bottom I/O Ports
1
RJ45 LAN Port
2
USB 2.0 Port
3
VGA Port
4
COM Port
(COM3/COM2/COM1)
5
RJ11 Cash Drawer Port
6
12VDC-IN Power Jack
Positioning your POS for a Perfect Viewing Angle
The adjustable Gen7 base is designed to help you determine an ideal
position for PS-3315/3315E/3316/3316E using its unique tilt
adjustment mechanism. As the below figures suggest, Gen7 base
basically provides three standard positioning solutions for your terminal:
Flat Folded mode, Low Profile mode, and Full Extended mode.
PS-3315/3315E/3316/3316E with Gen7 Base
Flat Folded mode
Low Profile mode
Full Extended mode
In general, PS-3315/3315E/3316/3316E will be set up beforehand in
Flat Folded mode and then packaged into the box for shipping. After it
is unpacked, you may re-adjust the terminal in either Low Profile
mode or Full Extended mode according to your situation. Below will
provide instructions on how to adjust the specific base connected to the
POS system. As a reminder, please be careful not to touch the LCD
panel while setting up the tilt angle. Please refer to the following
instructions on how to switch among different positioning modes to
find an ideal viewing angle for PS-3315/3315E/3316/3316E with Gen7
base.
1
2
3
4
5
6

5
1. Unpack PS-3315/3315E/3316/3316E,
which is supposed to be set in Flat
Folded mode, out of the package box
and then lay your POS system on a flat
surface.
2. Steady the base with one hand, and then
tilt the screen downwards.
3. Position your terminal in Full Extended mode
3.1 After grabbing the bottom edge of the screen with your hand,
gently move the screen upward until the screen is locked into
place with a click sound.
3.2 With the screen facing toward you, tilt
the screen up or down to your desired
angle. Please do not press on the LCD
panel while setting up the tilt angle.

6
4. Return your terminal back to Flat Folded mode from Full
Extended mode.
4.1 Tilt your screen in a horizontal position. Then, remove the
cable cover from the base.
4.2 Support the screen with one hand holding onto its bottom
edge. While pulling the lever backwards, move the display
downwards until the lever is lifted off the hook as shown in
the figure
4.3 Push the cable cover back.
4.4 Tilt the screen again to the
horizontal position.
Hook
Lever

7
5. Position the terminal in Low Profile mode.
5.1 Follow Step 4 to set up the termimal in
Flat Folded mode.
5.2 Tilt the screen all the way down
5.3 To tilt screen up or down to your
desired angle, please be advised to keep
the base steady with one hand to do so.
Do NOT press on the LCD panel while
setting up the tilt angle.
Installing Optional Upgrade Kits and Peripherals
PS-3315/3315E/3316/3316E can work with multiple optional upgrade
kits and peripheral devices, such as magnetic stripe reader (MSR), LCD
monitor, cash drawer and the like. Before installing an optional upgrade
kit and/or peripheral device, make sure that the system is powered off
and the external power source is removed from the POS box to prevent
electric hazard. For the detailed instruction, refer to each of the user
manuals of the optional upgrade kits and peripheral devices.

8
Connecting Power Adapter and I/O Cables
Gen7 base features its own cable management to assist you in well
organizing the cords whenever you need to connect peripheral devices
to PS-3315/3315E/3316/3316E. The following provides some useful
cable-routing instructions required to manage your cables.
1. Set up your terminal in Full Extended
mode and then tilt the screen all the way
down.
2. Remove the cable cover from the base.
3. Pull outwards the locking levers with
your forefingers and then remove the
neck cover in the direction shown by the
arrow.
4. Tilt the terminal to the horizontal
position. Then, thread cables through the
cable passage.
5. After tilting the screen all the way up,
remove the bottom I/O cover to locate
the bottom I/O plate.
Cable Passage

9
6. Connect the connector of the power
adapter to the 12VDC-IN power jack.
7. Tuck the extra cables inside the bottom
I/O compartment, and then push back the
cover to close it.
8. Tilt the screen all the way down.
9. After neatly arranging the cable, place back the neck cover.
10.Push back the cable cover. Please also make sure that cables can be
routed through the cable exit.
Cable Exit

10
Powering ON the PS-3315/3315E/3316/3316E
Power ON PS-3315/3315E/3316/3316E
Press down the power button for at least 3 seconds to
power on the POS.
Power OFF PS-3315/3315E/3316/3316E
In most cases, press the power button of the POS to
power the system off. If the terminal fails to turn off the
machine for unknown reasons, please be advised to hold
the power button more than 10 seconds to force a
shutdown of the system.
Once powering off the system, if you want to power it
on again, please wait at least 3 seconds.
Power LED Indicator
Power LED indicator, which is located at the
center of the bottom edge of the LCD panel, is
mainly responsible for notifying users of the
current system status by emitting various LED
signals. The chart provided below will offer
helpful information that you need to interpret
LED status.
LED
Status
Description
POWER
Solid blue
System power ON
Solid orange
System standby

11
Installing an Operating System
You are highly advised not to install an operating system on
PS-3315/3315E/3316/3316E without professional instructions. Not
only might the careless handling during installation cause irreversible
damage to your machine, but also the improper installation likely leads
to system malfunction or failure. Please contact with your dealers about
the issues of operating system installation.
Operating System Recovery
For PS-3315/3315E/3316/3316E models with preloaded operating
systems, you are not encouraged to recover your system without the
help of system integrators. Please be advised to contact your service
center for further assistance with system recovery.
Operation Environment
To prevent PS-3315/3315E/3316/3316E from overheating, it is
suggested to position your terminal in a well-ventilated working
environment. In doing so, please be advised to keep the POS terminal at
least 25mm away from other devices to ensure the machine is properly
cooled down and functioning normally.

12
Specifications
PS-3315/3316
PS-3315E/3316E
Processor
Intel Bay Trail-M, N2807
Intel Bay Trail-D, J1900
System
Memory
2GB DDR3L 1333MHz default
Storage Device
SATA x 1
SATA x 1
(supporting SSD only)
Power Supply
12V/40W (upgrades to 60W or higher when required)
OS support
Windows 7 / POSReady 7 / Windows Embedded 8.1
Industry / DOS/ Linux per request
LCD Panel
15" 1024 x 768 TFT LCD for PS-3315/3315E
15.6” 1366 x 768 TFT LCD for PS-3316/3316E
Touch sensor
5-wire resistive touch with front bezel
Touch
Controller
USB interface
Serial Port
4 ports, 3 x DB9 on bottom I/O plate + 1 x RJ50 on top I/O
plate, 5V/12V support on all COM ports
Parallel Port
1 port, via optional conversion cable
Standard USB
Port
5 external ports (4 on bottom I/O plate + 1 on top I/O plate)
+ 3 internal ports
LAN Port
10 / 100 / 1000 Mb x 1
Display Port
VGA x 1, 12V support for Posiflex monitors
CR Port
1 port, controlling 2 CR via optional Y-cable
PS/2 Port
Pin header inside service window
Audio
Buzzer only
WiFi
USB WiFi dongle
Base Stand
GEN7 foldable base
Environmental
Requirements
Operating :
0°C - 40°C, 20%RH - 90%RH (Equipped with HDD);
0°C - 50°C, 20%RH - 90%RH (Equipped with SSD)
Storage :
-20°C - 70°C, 10%RH - 90%RH