Pottinger Original inside NOVACAT 3007 T ED User manual

Operator‘s manual
Translation of the original Operating Manual
Nr.
99+3525.EN.80S.0
Disc mower
NOVACAT 3007 T ED / RC /RCB / Coll
(Type 3523: +..01001)
NOVACAT 3507 T ED / RC /RCB / Coll
(Type 3525: +..01001)

1500_GB-PAGE 2
Product liability, information obligation
Product liability obliges manufacturers and dealers to issue operating instructions for the machine at the point of sale and to
instruct
the customer on the operation, safety and maintenance regulations governing the machine.
A confirmation is required to verify that the machine and operating instructions have been handed over correctly.
For this purpose
- Document A
is to be signed and returned to Pöttinger or via the internet to www.poettinger.at
- Document B
remains with the specialist dealer handing over the machine.
- The customer receives document C
.
For the purposes of product liability law, every farmer is an entrepreneur.
In the terms of product liability law, damage to property is any damage arising due to the machine, but not to the machine, and
an
excess (500 euros) exists for this liability.
Corporate damage to property within the terms of the product liability law is excluded from this liability.
Be advised!
The operating instructions must also be handed over with any subsequent machine sale or transfer and the transferee
must be instructed in the regulations stated.
Pöttinger - Trust creates Af
À
nity - since 1871
À
"Quality pays for itself." Therefore we apply the highest quality standards to our products which are constantly monitored by o
ur
in-house quality management and our management board. Because the safety, perfect function, highest quality and absolute
reliability of our machines in operation are the core competencies for which we stand.
There may be deviations between these instructions and the product as we are constantly developing our products. Therefore no
claims may be derived from the data, illustrations and descriptions. Please contact your Specialist Service Centre for any bind
ing
information about specific features of your machine.
We would ask you to please understand that changes to the scope of supply with regard to form, equipment and technical
specifications are possible at any time.
Any form of reprint, translation or reproduction, including excerpts, requires the written approval of Pöttinger Landtechnik Gm
bH.
All rights according to copyright laws remain expressly reserved by Pöttinger Landtechnik GmbH.
© Pöttinger Landtechnik GmbH – 31st October 2012
Refer to PÖTPRO for additional information about your machine:
Are you looking for suitable accessories for your machine? No problem! All the information you require is here at your disposal
.
Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro
Scan the QR code on the machine's type plate or look under www.poettinger.at/poetpro
And if we don't have what your looking for, then your Specialist Service Centre is there for you with help and advice.

Dokument
D
GB-0600 Dokum D Anbaugeräte
- 3 -
PÖTTINGER Landtechnik GmbH
Industriegelände 1
A-4710 Grieskirchen
Tel. 07248 / 600 -0
Telefax 07248 / 600-2511
T
Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating
devices at hand.
T
Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.
T
Tyres checked re. correct pressure.
T
Wheel nuts checked re. tightness.
T
Drive shaft cut to correct lenght.
T
Correct power-take-o
Ɉ
speed indicated.
Ɉ
T
Fitting to tractor carried out: to three-point linkage
T
Trial run carried out and no defects found.
T
Functions explained during trial run.
T
Pivoting in transporting and operating position explained.
T
Information given re. optional extras.
T
Absolute need to read the operating manual indicated.
Please check.
X
According to the product liability please check the above mentioned items.
INSTRUCTIONS FOR
PRO
DUCT DELIVERY
EN
EN
In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.
For this purpose please do the following:
- sign the
document A
and send it to the company Pöttinger or via the internet to www.poettinger.at
-
document B
stays with the specialist factory delivering the machine.
-
document C
stays with the customer.

- 4 -
EN
INTRODUCTION
1700_GB-Introduction
Introduction
Dear Customer
These Operating Instructions are intended to allow you
to familiarise yourself with the implement and provide
you with clear information on safe and correct handling,
care and maintenance. Thus please take the time to read
these Instructions.
These Operating Instructions comprise part of the imple-
ment. They are to be kept at a suitable location and acces-
sible to staff over the entire service life of the implement.
Instructions based on the national provisions regarding
protectionagainstaccidents,roadtrafficandenvironmental
protection are also to be applied additionally.
Anypersonscommissionedwiththeoperation,maintenance
or transport of the implement must read and understand
these Instructions, in particular the safety information, prior
to starting work. Any warranty claims lapse on non-obser-
vance of these Instructions.
Incase youhavequestionsrelatedtothis operationmanual
or further questions about this implement, please contact
your dealer.
Care and maintenance performed in good time and scru-
pulously according to the maintenance intervals specified
ensureoperationalandtraffic safetyas wellas thereliability
of the implement.
Use only the original spare parts and accessories from
Pöttinger or accepted by Pöttinger. For those parts relia-
bility, safety and suitability for Pöttinger machines can be
assured. Warranty claims lapse if non-approved parts are
used. The use of original parts is also recommended after
thewarrantyperiodhasexpiredtomaintaintheperformance
of the implement in the long term.
Product liability legislation obliges the manufacturer and
the authorised dealer to issue Instructions when selling
implements and to instruct customers in the use with refer-
ence to the safety, operating and maintenance regulations.
Confirmation in the form of a declaration of transfer is
required to verify that the implement and Instructions have
been transferred correctly. The declaration of transfer was
attached to the implement on delivery.
Every self-employed person and farmer is an entrepreneur
within the meaning of the product liability legislation. In
accordance with the laws of product liability, entrepre-
neurial property damages are excluded from the liability.
All damage to property within the meaning of the product
liability legislation is regarded as damage caused by the
implement but not to the implement.
These Operating Instructions are integral part of the imple-
mentdeliveryscope.Youshouldthereforehandthemoverto
the new owner if ownership of the implement is transferred.
Train and instruct the new owner in the regulations stated.
The Pöttinger Service-Team wishes you good luck.

- 5 -
EN
1700_GB-Inhalt_3525
TABLE OF CONTENTS
Table of contents
Introduction................................................................ 4
SYMBOLS USED
CE mark..................................................................... 6
Safety hints: ............................................................... 6
WARNING SIGNS
Meaning of warning signs.......................................... 7
ATTACHING
Safety advice ............................................................. 9
Attaching to tractor..................................................... 9
First fitting of the machine........................................ 10
Hydraulic connection ............................................... 10
Cardan shaft length ................................................. 10
Drive speed control ..................................................11
SETTINGS
Set the mower bar bearing pressure at the
mainsprings ............................................................. 12
Set the mower bar cutting height ............................. 12
Tine conditioner: Change rotor rpm ......................... 13
Tine conditioner: Set degree of processing ............. 13
TRANSPORT AND WORKING POSITION
Changing from transport to working position ............14
Changing from working position to transport
position .................................................................... 15
Road Transport ........................................................ 16
OPERATION
Important notes prior to the start of work..................17
ATTACHING
Safety advice ........................................................... 18
Attaching to tractor................................................... 18
First fitting of the machine........................................ 19
Hydraulic connection ............................................... 19
Cardan shaft length ................................................. 19
Drive speed control ................................................. 20
CROSS CONVEYOR BELT
Safety advice ........................................................... 21
Road Transport ........................................................ 21
Cross conveyor function .......................................... 21
Cross conveyor operation........................................ 22
Cable harness cross conveyor................................. 24
Hydraulic plan cross conveyor ................................. 25
Control panel cross conveyor................................... 26
TINE CONDITIONER
Operation mode....................................................... 27
General safety information....................................... 27
Possible settings...................................................... 27
Operation................................................................. 29
Maintenance ............................................................ 29
Rotor tines: .............................................................. 30
Detaching and attaching the conditioner ................. 30
ROLLER CONDITIONER
Safety advice ........................................................... 31
Operation mode ....................................................... 31
Overview.................................................................. 31
Possible settings...................................................... 32
Operation................................................................. 33
Maintenance ............................................................ 33
Roller conditioner for collector ................................. 36
UNCOUPLE THE MACHINE
Uncouple the machine............................................. 37
GENERAL MAINTENANCE
Safety advice ........................................................... 38
General maintenance information............................ 38
Cleaning of machine parts....................................... 38
Parking in the open.................................................. 38
Winter storage.......................................................... 38
Articulated shafts ..................................................... 39
Hydraulic unit........................................................... 39
Wear control cutting blades bracket
......................... 40
Holder for the rapid change of mowing blades ........41
Mowing blades suspension checks .........................41
Changing the mowing blades ...................................41
After the first operation hours .................................. 42
Winter standstill ....................................................... 42
Every 50 operating hours
......................................... 42
Mower bar oil change .............................................. 42
Cross conveyor belt maintenance............................ 44
Inductive sensor - Cross conveyor belt:................... 44
Disposal of old equipment ....................................... 44
Lifting the implement................................................ 45
Transmission............................................................ 46
Taper bushes installation instructions...................... 47
TECHNICAL DATA
Technical data.......................................................... 48
The defined use of the mower unit........................... 48
Type plate ................................................................ 49
Type plate position................................................... 49
SUPPLEMENT
SAFETY ADVICE
NOVACAT 3007 T ED /RC / Coll.............................. 56
NOVACAT 3507 T ED / RC /Coll.............................. 56
Lubrication chart ...................................................... 58
Lubricants ................................................................ 59
Tightening torque..................................................... 62
Air pressure ............................................................. 62
Power supply ........................................................... 65
Fitting of the control panel ....................................... 65
Setting up
................................................................. 66
Reverse gearbox
...................................................... 66

- 6 -
1800_EN-Sicherheit ANSI
EN
SYMBOLS USED
CE mark
The CE mark, which is affixed by the manufacturer, indicates outwardly that this machine conforms to the engineering
guideline regulations and the other relevant EU guidelines.
EU Declaration of Conformity (see Attachment)
By signing the EU Declaration of Conformity, the manufacturer declares that the machine that
is brought into service complies with all relevant fundamental safety and health requirements.
Safety hints:
These Operating Instructions contain the
following Figures:
DANGER
If you do not follow the instructions in a text section
If you do not follow the instructions in a text section
with this marking, there is a risk of fatal or life-
with this marking, there is a risk of fatal or life-
with this marking, there is a risk of fatal or life-
threatening injury.
threatening injury.
threatening injury.
• All instructions in such text sections must be
• All instructions in such text sections must be
followed!
WARNING
If you do not observe the instructions marked this
way, there is the risk of a severe injury.
way, there is the risk of a severe injury.
• All instructions in such text sections must be
• All instructions in such text sections must be
followed!
CAUTION
If you do not observe the instructions marked this
way, there is the risk of an injury.
• All instructions in such text sections must be
• All instructions in such text sections must be
followed!
NOTE
NOTE
NOTE
If you do not observe the instructions marked this
way, there is the risk of material damage.
way, there is the risk of material damage.
• All instructions in such text sections must be
• All instructions in such text sections must be
followed!
TIP
The text sections marked in this way provide you with
The text sections marked in this way provide you with
special recommendations and advise regarding the
economical use of the implement.
economical use of the implement.
ENVIRONMENT
The text sections marked in this way provide practices
and advice on environmental protection.
The features marked as (optional) are only available as
standard with specific implement versions or are only
offered for specific versions as optional equipment or are
only offered in certain countries.
Figures may deviate from your implement in detail and are
to be taken as illustrations of operating principle.
Designations such as right and left always apply as the
direction of travel unless the text or illustrations clearly
show otherwise.

- 7 -
EN
1800_GB-Warning signs_3525
WARNING SIGNS
Meaning of warning signs
1
495.158/17
Do not touch rotating machine components.
Wait until they have stopped completely. 495158
2
bsb 447 410
Danger from
Å
ying objects when the engine is running.
Å
- Keep a safe distance 495152
3
Close the protection before turning on the cardan shaft - risk of
injury by
Å
ying objects 495167.
Å
4
Lifting point for crane 495404.

- 8 -
EN
1800_GB-Warning signs_3525
5
Lubrication point for grease 494646.
6
Read the operating instructions before initial operation 494529
7
Never reach into the crushing danger area as long as parts can
move there. 495171
8
Free the swivelling area of the unit - Danger of being hit by the
swivelling unit. 495157
9
Shut engine o
Ɉ
and remove key before carrying out main-
Ɉ
tenance or repair work. 495165

- 9 -
EN
1800_GB-Operation_3525
ATTACHING
Safety advice
DANGER
Life-threateningdangerthroughoperatinga machine
that is unroadworthy or damaged.
• Check the vehicle for roadworthiness prior
to every operation (lights, brakes, protective
panels …)!
• Regularly check tightness of the blades,
bolts and tine conditioners.
For further safety instructions
see Annex-A1, 1-8.
Attaching to tractor
Starting position
355-08-04
1
2
9
8
3
7
62-00-14
62-00-14
Park machine with support foot (7) on level ground, pin
with bolts (8) and secure with spring cotter (10).
Attachment
• Secure the hydraulic lower link, so that machine cannot
swing out sideways.
- Against uneven, unstable trailing of the machine.
- Attach and lock at this height the lower linkage to the
pipe bend (9).
The mounting height corresponds to the parking height
on firm ground.
- Attach safety chain:
Connect the lower linkage to the tractor with the safety
chain (1).
At the lower link side, the safety chain is to be attached
to the inner side of the mounting pins
At the tractor side, no statement to be made from our
side, as the tractor is exported in too many different
models.
017-18-006
1
TIP
By an unintentional separation of the couplings, the
By an unintentional separation of the couplings, the
safety chain works provisionally instead of the hanger, to
allow for it to run behind the tractor. The safety chain also
prevents the unit to touch the ground with the drawbar.
Fold up support stand (7): Pos A
- Stake support foot (7) with bolts (8) and secure with
spring cotter (10).
7
8
9
A
B
355-08-05
10

- 10 -
EN
1800_GB-Operation_3525
ATTACHING
Connect hydraulic lines at tractor
- Guide the hydraulic lines through the cable guide (13).
- Attach the stake couplings of the hydraulic lines.
1 = Extend the drawbar cylinder
2 = Retract the drawbar cylinder
3 = Raise the wheel carrier
4 = Raise the wheel carrier
Connecting the electrical system
- Guide the lines through the cable guide (13)
- Connect
- Electrical system: see Supplement
First fitting of the machine
Hydraulic connection
On the tractor there have to be at least
• 1 double-acting (11) and
• 1 single-action (12)
hydraulic plug connection.
Cardan shaft length
Before first use, check the length of the cardan shaft and
if necessary adjust it.
See also Chapter "cardan shaft" in Supplement B as well
as attached Operating Instructions of the cardan shaft.
TIP
Use the correct cardan shaft!
Use the correct cardan shaft!

- 11 -
EN
1800_GB-Operation_3525
ATTACHING
Drive speed control
(Tractor side)
TD8/95/6a
1000 rpm
= Standard-Drive Speed
The pivoting gear (PG) has been factory set for operation
with this rpm (delivery condition).
1 Cardan shaft rotation = 3 mowing discs-rotations
540 rpm
If the tractor can only achieve a drive speed (up to 540
rpm), then the transmission (PG) must be removed and
reinstalled inverted.
1 Cardan shaft rotation = 6 mowing discs rotations
1000 rpm
1000 rpm
540 rpm
SG
S
H
TD24/95/47
• Thereby safely support the drawbar! (For example
with a stable wood log "H")
• Subsequently mount the protective head (PH) again
TIP
For further details see chapter
"Turn gearing round"
attached!

- 12 -
1700_GB-Setting_3522
EN
Set the mower bar bearing pressure at
the mainsprings
y
11
Adjustment process:
1. Lift the handle (12) up from the bracket (13).
2. Rotate the threaded spindle accordingly.
3. Secure the handle (12) in the bracket (13) again.
- Inthispositionthethreadedspindleissecuresagainst
twisting.
TIP
The mower bar bearing load on the ground should be
approx. 150 kg (approx. 75 kg left and right)
SETTINGS
Spring setting dimensions
Type of machine
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
NOVACAT 307 T NOVACAT 3007 T NOVACAT 3507 T
x (mm)
160
155
145
y (mm)
300
220
200
TIP
The spring setting dimensions are approximate values.
The spring setting dimensions are approximate values.
These can vary due to component tolerances, tyre pres-
These can vary due to component tolerances, tyre pres-
sure as well as tyre dimensions. Where necessary, the
relief springs should be readjusted.
Set the mower bar cutting height
For optimal operation the telescopic upper link setting
should be 580 mm.
11
580 mm
The hinged plate (14) serves as a cutting height indicator
as well as anti-twist protection.

- 13 -
1700_GB-Setting_3522
EN
SETTINGS
Adjustment process:
1. Lift the hinged plate (14).
2. Twist the telescopic upper link (11) accordingly.
- Increase cutting height - twist right
- Decrease cutting height - twist left
3. Secure telescopic upper link against twisting with the
hinged plate (14).
Tine conditioner: Change rotor rpm
355-08-09
A
B
By swapping the belt pulleys (A) and (B), the conditioning
rpm can be altered from 1000 rpm to 700 rpm.
• Speed: 1000 rpm
Upper belt pulley ø 197 mm
Lower belt pulley ø 167 mm
(Normal rpm)
• Speed: 700 rpm
Upper belt pulley ø 167 mm
Lower belt pulley ø 197 mm
This rpm is recommended for leafy forage. The
forage is not crushed so strongly.
Tine conditioner: Set degree of
processing
The gap between the beating arm and rotor is adjusted
using the hand lever. As a result, the conditioning effect
can be altered.
3
2
1
0
355-08-15
• Conditioning is most effective in the lowest position
(3)astheforagesurfaceisstronglyreamed.However,
the fodder must not be beaten.
• The opposite occurs in the top position (0) as the
forage surface is only lightly reamed.
Among other things, the right setting depends on the
quantity of cut material, driving speed and tractor
capacity. Therefore, any binding recommendation
regarding the correct lever setting cannot be made at
this time.

- 14 -
1800_GB-Transport and working position_3525
EN
Changing from transport to working
position
CAUTION
Risk of injury exists through swivelling of the unit.
Risk of injury exists through swivelling of the unit.
• Control the pivot range of the unit immedi-
ately before pivoting.
ately before pivoting.
• Inform the people in the pivot range or
close, out of the danger zone.
1. Undo hydraulic circle
- Swing lever to position E1.
2. Swing out the machine
• Swivel cylinder (5)
- Retract fully: Pos A
- Extend fully: Pos. B
355-08-7
M
5
5
TRANSPORT AND WORKING POSITION
3. Lower the machine
• Undo double-sided lift cylinder (1)
- Swing lever to position
A1
- Retract lift cylinder fully (1)
3
55-08-06
1
TD 495.732
A1
T1
5. Fold down side hoop guard (9) to working
position (left and right)
- Remove linch pin (10).
- Remove hoop guard.

- 15 -
1800_GB-Transport and working position_3525
EN
TRANSPORT AND WORKING POSITION
Changing from working position to
transport position
DANGER
Life hazard - due to rotating or tossed components
• Switch off the cutter bar drive, before switch-
• Switch off the cutter bar drive, before switch-
ing to transport position.
• Wait until the cutter bar has stopped moving
before you swivel it to transport position.
DANGER
Life hazard - due to moving parts
• Make sure that the swivel range is clear and
• Make sure that the swivel range is clear and
that no-one is standing in the danger area.
NOTE
NOTE
NOTE
Risk of property damage exists when leaving the
machine
• Do not park the machine, when the flange
surfaces are not tight bolted with each other.
1. Lift the machine
• Extend lift cylinder fully (1)
• Lock double-sided lift cylinder (1)
- Swing lever to position
T1
3
55-08-06
1
TD 495.732
A1
T1
2. Swing in the machine
• Extend or retract the swivel cylinder (5) fully
- Bring the drawbar to middle position (Pos M)
- Tab (15) and tab (16) must be placed in the flight
line
3. Lower cross conveyor belt
4. - Fold up the side protection (9) and secure
using the bolt pin (10)
5. Lock hydraulic circle
- Swing lever to position E2.
355-08-7
M
5
15
16

- 16 -
1800_GB-Transport and working position_3525
EN
TRANSPORT AND WORKING POSITION
Road Transport
DANGER
Life danger by unintentional swivelling of the unit
during transportation in open traffic.
• Lock the hydraulic circle at the locking valve
while driving (Lever in Pos. E2)
• Driving on public roads is permitted only transport
position!
• Fold up hoop guard (9).
- Remove linch pin (10).
- Fold up hoop guard.
- Secure with linch pin..
• Check lights and security equipment.

- 17 -
EN
1800_GB-Operation_3522
OPERATION
Important notes prior to the start of work
After the first hours of operation
• Pull all blade fittings.
1. Check
- Check the condition of the blades and mount.
- Check mowing discs for damage (see chapter
"Maintenance and Service").
2. Switch the machine on, only when in working
positionandexceedthestipulatedp.t.o.speed,
accordingtothe gearbox:Not 540 or 1000rpm!
• Always,andonly,switchthep.t.o.driveonwhenallsafety
devices (covers, protective aprons, casings, etc.) are
in proper condition and are attached to the machine in
their safety positions.
3. Pay attention to correct p.t.o. direction of
rotation! If rotation direction is wrong, then
the drive runs empty in the free-running drive
shaft.
4. Prevent any damage!
The area to be mowed must be free of obstacles or foreign
objects.Suchobjects(e.g.largestones,piecesofwood,
boundary stones, etc.) can damage the mower unit.
If, nevertheless, a collision occurs,
• Stop immediately and switch off the drive.
• Check the machine carefully for any damage. You must
check in particular the mowing discs and their drive
shafts.
• If necessary have it checked over in a specialist work
shop as well.
After contact with a foreign object
• Check the condition of knives and the knife fixings.
• Retighten all blade screw fittings.
5. Keep away from the engine when it's running
bsb 447 410
• Guidepeopleoutofthedangerareaasthey maybecome
injured by foreign objects being ejected by the mower.
Special care is necessary on stony ground, and near
roads and paths.
6. Wear hearing protection
The noise level in the workplace can deviate from
the measured value (see Technical Data) particularly
through the differing types of tractor cabins.
• If a noise level of 85 dB (A) is reached or exceeded,
then the contractor (farmer) must have suitable hearing
protection readily available (UVV 1.1 § 2).
• If a noise level of 90 dB (A) is reached or exceeded,
then hearing protection must be worn (UVV 1.1 § 16).
7. Check the condition of the V-Belts.
Replace worn and damaged V-Belts!
8. Control V-Belt tension!
The disc on the compression spring must be set at a
higher reference dimension. Setting is performed in
accordance to twisting of the adjusting nut.
Then secure with lock nut (see chapter "Maintenance
and Service").
9. For mowing, slowly engage the p.t.o. shaft
away from the crop and bring the mower rotor
up to full speed.
Smoothly increasing the p.t.o. speed will avoid system-
related noises from the p.t.o. free-wheel.
- The driving speed depends on the ground conditions
and the crop to be mown.
TIP
Further safety instructions: see Annex A1.

- 18 -
EN
1800_GB-Operation_3525
ATTACHING
Safety advice
DANGER
Life-threateningdangerthroughoperatinga machine
that is unroadworthy or damaged.
• Check the vehicle for roadworthiness prior
to every operation (lights, brakes, protective
panels …)!
• Regularly check tightness of the blades,
bolts and tine conditioners.
For further safety instructions
see Annex-A1, 1-8.
Attaching to tractor
Starting position
355-08-04
1
2
9
8
3
7
62-00-14
62-00-14
Park machine with support foot (7) on level ground, pin
with bolts (8) and secure with spring cotter (10).
Attachment
• Secure the hydraulic lower link, so that machine cannot
swing out sideways.
- Against uneven, unstable trailing of the machine.
- Attach and lock at this height the lower linkage to the
pipe bend (9).
The mounting height corresponds to the parking height
on firm ground.
- Attach safety chain:
Connect the lower linkage to the tractor with the safety
chain (1).
At the lower link side, the safety chain is to be attached
to the inner side of the mounting pins
At the tractor side, no statement to be made from our
side, as the tractor is exported in too many different
models.
017-18-006
1
TIP
By an unintentional separation of the couplings, the
By an unintentional separation of the couplings, the
safety chain works provisionally instead of the hanger, to
allow for it to run behind the tractor. The safety chain also
prevents the unit to touch the ground with the drawbar.
Fold up support stand (7): Pos A
- Stake support foot (7) with bolts (8) and secure with
spring cotter (10).
7
8
9
A
B
355-08-05
10

- 19 -
EN
1800_GB-Operation_3525
ATTACHING
Connect hydraulic lines at tractor
- Guide the hydraulic lines through the cable guide (13).
- Attach the stake couplings of the hydraulic lines.
1 = Extend the drawbar cylinder
2 = Retract the drawbar cylinder
3 = Raise the wheel carrier
4 = Raise the wheel carrier
Connecting the electrical system
- Guide the lines through the cable guide (13)
- Connect
- Electrical system: see Supplement
First fitting of the machine
Hydraulic connection
On the tractor there have to be at least
• 1 double-acting (11) and
• 1 single-action (12)
hydraulic plug connection.
Cardan shaft length
Before first use, check the length of the cardan shaft and
if necessary adjust it.
See also Chapter "cardan shaft" in Supplement B as well
as attached Operating Instructions of the cardan shaft.
TIP
Use the correct cardan shaft!
Use the correct cardan shaft!

- 20 -
EN
1800_GB-Operation_3525
ATTACHING
Drive speed control
(Tractor side)
TD8/95/6a
1000 rpm
= Standard-Drive Speed
The pivoting gear (PG) has been factory set for operation
with this rpm (delivery condition).
1 Cardan shaft rotation = 3 mowing discs-rotations
540 rpm
If the tractor can only achieve a drive speed (up to 540
rpm), then the transmission (PG) must be removed and
reinstalled inverted.
1 Cardan shaft rotation = 6 mowing discs rotations
1000 rpm
1000 rpm
540 rpm
SG
S
H
TD24/95/47
• Thereby safely support the drawbar! (For example
with a stable wood log "H")
• Subsequently mount the protective head (PH) again
TIP
For further details see chapter
"Turn gearing round"
attached!