Pottinger LION 5000 User manual

/PERATOR@SMANUAL
GB
Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.
).3425#4)/.3&/202/$5#4$%,)6%290AGE
4RANSLATIONOFTHEORIGINAL/PERATING-ANUAL
Ihre / Your / Votre • Masch.Nr. • Fgst.Ident.Nr.
.R
• Rotary Harrow
LION 5000
(Type 5000: + . . 01001)
LION 6000
(Type 6000: + . . 01001)
99 877.GB.80I.0

ALLG./BA SEITE 2 / 0000-GB
Important information concerning Product
Liability.
According to the laws governing product liability, the manufacturer and dealer are obliged to hand the
operating manual to the customer at the time of sale, and to instruct them in the recommended operating,
safety, and maintenance regulations. Conrmation is necessary to prove that the machine and operating
manual have been handed over accordingly.
For this purpose,
- document A is to be signed and sent to Pöttinger,
- document B remains with the dealer supplying the machine,
- and the customer receives document C.
In accordance with the laws of product liability, every farmer is an entrepreneur.
According to the laws of product liability, property damage is damage caused by a machine and not to
it. An excess of Euro 500 is provided for such a liabilioty.
In accordance with the laws of product liability, entrepreneurial property damages are excluded from
the liability.
Attention! Should the customer resell the machine at a later date, the operating manual must be given
to the new owner who must then be instructed in the recommended regulations referred to herein.
GB Dear Farmer
You have just made an excellent choice. Naturally we are very happy
and wish to congratulate you for having chosen Pöttinger. As your
agricultural partner, we offer you quality and efciency combined with
reliable servicing.
In order to assess the spare-parts demand for our agricultural machines
and to take these demands into consideration when developing new
machines, we would ask you to provide us with some details.
Furthermore, we will also be able to inform you of new developments.

Dokument D
GB-0600 Dokum D Anbaugeräte - 3 -
ALOIS PÖTTINGER Maschinenfabrik GmbH
A-4710 Grieskirchen
Tel. [phone]
Telefax [phone]
GEBR. PÖTTINGER GMBH
D-86899 Landsberg/Lech, Spöttinger-Straße 24
Telefon [phone] / 112
Telefax (0 81 91) 92 99-188
GEBR. PÖTTINGER GMBH
Servicezentrum
D-86899 Landsberg/Lech, Spöttinger-Straße 24
Telefon [phone] / 231
Telefax (0 81 91) 59 656
Machine checked according to delivery note. All attached parts removed. All safety equipment, drive shaft and operating
devices at hand.
Operation and maintenance of machine and/or implement according to operating instructions explained to the customer.
Tyres checked re. correct pressure.
Wheel nuts checked re. tightness.
Drive shaft cut to correct lenght.
Correct power-take-off speed indicated.
Fitting to tractor carried out: to three-point linkage
Trial run carried out and no defects found.
Functions explained during trial run.
Pivoting in transporting and operating position explained.
Information given re. optional extras.
Absolute need to read the operating manual indicated.
Please check. X
According to the product liability please check the above mentioned items.
INSTRUCTIONS FOR
PRODUCT DELIVERY
GB
In order to prove that the machine and the operating manual have been properly delivered, a confirmation is necessary.
For this purpose please do the following:
- sign the document A and send it to the company Pöttinger
(in case of Landsberg equipment: to the company Landsberg)
- document B stays with the specialist factory delivering the machine.
- document C stays with the customer.

- 4 -
0800_GB-INHALT_877
GB
CONTENTS
CE sign
The CE sign, which is affixed by the
manufacturer, indicates outwardly
that this machine conforms to the
engineering guideline regulations and
the other relevant EU guidelines.
EU Declaration of Conformity
By signing the EU Declaration of Conformity, the
manufacturer declares that the machine being brought
into service complies with all relevant safety and health
requirements.
Meaning of warning signs
Danger - stay clear of rotating machine parts
Danger-ying objects; keep safe distance from
the machine as long as the engine is running.
Never reach into the crushing danger area as
long as parts may move.
Not step onto the machine
when PTO is connected
and engine is running.
Observe Safety Points in Supplement A!
bsb 44 410
Table of contents
CE sign .............................................................................................. 4
Meaning of warning signs ................................................................. 4
CONNECTING TO TRACTOR
Preparing the tractor ......................................................................... 5
Preparing the implement ................................................................... 5
Track loosener (Optional equipment)................................................. 5
TRANSPORT POSITION - WORKING POSITION
Conversion from working to transport position................................. 6
Driving on public roads ..................................................................... 6
Conversion from transport to working position................................. 7
Parking in the open ........................................................................... 7
Garaging the implement.................................................................... 7
Before uncoupling the hydraulic hoses............................................. 7
Take care when turning on slopes!.................................................... 8
OPERATION
Lightning during use on roads........................................................... 9
Check before putting into operation ................................................. 9
Change speed transmission.............................................................. 9
Working depth adjustment ................................................................ 9
Stripping plates ............................................................................... 10
Adjusting the Stripping plates ......................................................... 10
Side shields ..................................................................................... 10
Safety points ................................................................................... 10
OVERLOAD CUT-OUT
Cam clutch function (1600 Nm)....................................................... 11
Cam clutch adjustment ................................................................... 11
Dismantling the cam clutch............................................................. 11
MAINTENANCE AND SERVICE
Advice for general maintence.......................................................... 12
Winter storage ................................................................................. 12
Hydraulic unit .................................................................................. 12
Important montage hint .................................................................. 12
Changing the tines .......................................................................... 13
Greasing .......................................................................................... 13
Spur wheel - angular gear ............................................................... 13
Lubrication chart(GB) ..................................................................... 14
TECHNICAL DATA
Technical data ................................................................................. 16
Necessary connections ................................................................... 16
Optional equipment......................................................................... 16
Location of Identication Plate........................................................ 17
The Dened Use of the Rotary Harrow ........................................... 17
SUPPLEMENT
Recommendations for work safety ................................................ 20
Driveshaft ........................................................................................ 21
Lubricants........................................................................................ 23
Combination of tractor and mounted implement............................ 25

GB
- 5 -
0000-gb anbau_877
CONNECTiNg TO TraCTOr
Preparing the tractor
Ballast weight:
Observe Safety points in Supplement!
Lifting gear
- The left and right lifting struts (4) must be the same length.
Adjust using adjuster (3).
- If lifting struts (4) can be pinned at various positions on the lower
links, then select the back position (H). In doing this, the tractor’s
hydraulics will not be so greatly overloaded.
- Pin (2) upper link (1) in accordance with the manufacturer’s
specifications.
- Secure lower links with struts (5) so that attached implement cannot
swing out during transportation.
Preparing the implement
Mounting axle
Install correct mounting bar on tractor’s lifting gear which corresponds
to the connecting size (Category II or III). See Spare Parts List also.
Upper link
- Position upper link (1) so that the attachment point (P1) on the
implementduring operation is somewhathigherthantheattachment
point (P2) on the tractor.
Connect drive shaft
- Check drive shaft length and adapt if necessary before initial
operation.
See chapter "Drive Shaft" in Supplement B also.
Track loosener (Optional equipment)
Only use track loosener when working on ploughed ground!
TD65/92/2
1P1
P2

GB
- 6 -
0000-gb TransporT_877
TraNspOrT pOsiTiON -
WOrkiNg pOsiTiON
Conversion from working to transport position
Safety Precaution!
see supplement-A1 points 7.), 8c. - 8h.)
• Changingfromworkingpositiontotransportposition
is only to be carried out on even, firm ground.
• Make sure that swivel area is free and that nobody
is standing in the danger area.
- heed the distance (17) to the rear window!
1. switch off the PTO drive shaft
2. raise implement using the tractor’s lifting gear (H1)
3. secure both packer rollers in the lowermost position
with bolts (15)
4. risebothrotaryharrowsintothetransportationposition
(T)
- use the appertaining double-action control valve for this
Security equipment
A security equipment is installed at the two swing cylinders. This
is always actively and prevents the sudden turning away of the
two rotary harrows if a hydraulic line becomes leaky or a hydraulic
hose is damaged.
The security equipment is not allowed to off or is
changed!
Important!
In the transport position (T), the machine cannot be
parked longer time.
- The casing bearing in the inner of the gear balk is filled with
transmission grease. This grease could flow out, the lubrication
would be no longer sufficient then
Driving on public roads
• Observe the official regulations of your country.
• Travelling on open roads may only be carried out as described
in chapter "Transport position".
• Protection devices must be in proper condition.
• Beforetravellingbringallswivellingpartsintotheircorrectpositions
and secure against dangerous changes to position.
• Check that lighting functions before travelling.
• Important information can also be found in the supplement of this
operating manual.

GB
TraNspOrT pOsiTiON -
WOrkiNg pOsiTiON
-  -
0000-gb TransporT_877
Conversion from transport to working position
• Make sure that swivel area is free and that nobody is standing in
the danger area.
Work steps
- see previous page,
however in reverse
order.
Hint
Turning away of the two rotary harrows into the working position
can take place only with one double acting hydraulic valve. The
security equipment (hydraulic barrier) is deactivated only by hydraulic
pressure.
Parking in the open
When parking in the open for
long periods of time, clean
plunger rods and then coat with
grease.
Garaging the implement
- Implement stops only in working position
- Park implement on firm and even ground.
- With soft underground use a stable base
- Pull support stand (18) out and secure with spring pin.
- Uncouple drive shaft from tractor.
- Remove upper link from implement.
- Uncouple the hydraulic lines from tractor.
FETT
Before uncoupling the hydraulic hoses
• Move control valve (EW) to „lower“ position
This will release any possible residual pressure present in the
lines.
2-way-valve
A = closed
E = open

0000-gb HangfaHrT_877 - 8 -
GB
wOrkiNg ON SlOpES
Take care when turning on slopes!
Thetractor'stravelling characteristicsare influenced
by the weight (G) of the machine. This can lead to
dangerous situations, especially on slopes.
Danger of tipping occurs
• when the both machines are in a raised position
- The machine facing uphill is always raised first which results
in uneven weight distribution (G).
• when travelling in a curve with both machines raised
Safety advice
• Reduce speed in curves accordingly.
• It is better to travel in reverse on a slope than to carry out a risky
turning manoeuvre.

GB
- 9 -
0000-gb EInsaTZ_877
OpEraTiON
Lightning during use on roads
If desired, a lightning unit can be supplied.
For single parts see spare parts list.
Check before putting into operation
- Implement connected horizontally.
- Upper link correctly positioned.
- Lower link (4) laterally secured.
- Drive shaft adapted to correct length.
- Rotary r.p.m. pre-selected per table.
Change speed transmission
The rotor r.p.m. (215, 296, 393 min-1) is to be preselected from the
table according to operating conditions and tractor power.
Attention!
• Combustion danger through hot gears
- this hint is applied to all gears at the machine
- hold distance, use protective gloves
• Before operating the gear control lever turn off the
motor
Safety point
Danger - stay clear
of rotating machine
parts.
Observe safety
distance when engine
is running with p.t.o.
connected.
Power-take-off r.p.m. 1000 min-1
Hint:
Use only this r.p.m. so that various drive components on the tractor
and implement are not subject to additional load.
Working depth adjustment
The working depth (T) is determined by the swivel range of the
attached roller.
The left and right bolts act as buffers when they are placed in
corresponding holes in the hole pattern.
For safety reasons, implement should stand on the
ground when adjustments are being made.
- Twist and remove bolts.
- Place left and right bolts in the corresponding holes and secure
by twisting.
495.737
III.
II.
215
1000 296 393
I.
min
-1
min
-1

GB
OpEraTiON
- 10 -
0000-gb EInsaTZ_877
Stripping plates
Adjusting stripper carrier is carried out by unscrewing both nuts
(11) left and right.
Check beforehand that individual stripping plates (10) are
equidistant to the roller.
Adjusting the Stripping plates
- Turn roller, thereby checking the stripper plate (10) gap.
- Loosen hexagonal screw (SK) and correctly set stripper plate.
- Turn roller once again and check.
bsb 44 410
Side shields
Side shields (20) can be
screwed on at various
points.
Theposition shouldsuitthe
working depth.
Rear deflector (Optional
equipment)
Rear deflector (31) height
isadjustableandtherefore
adapts to the respective
working depth.
With damp and sticky
ground the rear deflector
shouldbesetatthehighest
position or removed.
Safety points
• Onlyoperatethemachine
under the following
conditions:
1. when the both protection
tubes (30a) are installed.
2. when the rear rail (31) or a trailing implement (cage drum roller,
Packer roller) is attached.
3. whenboth sideshields(20) areswivelleddownandtheappropriate
working depth is set.
• Stay clear while engine
is running.
Keep people out of the
danger area where the risk
ofinjury fromejectedforeign
bodies exists.
Take particular care on stoney fields, and near streets and
roads.
• Turn p.t.o. off when raising the machine.

- 11 -
0000-gb gWsIcHErung_877
GB
OVErLOaD CUT-OUT
Cam clutch function (1600 Nm)
The cam clutch switches the drive off when it becomes overloaded.
The switched off clutch can be switched on again by uncoupling the p.t.o.
drive.
Take note!
Sensible operation prevents frequent clutch response and preserves
against unnecessary wear and tear.
Cam clutch adjustment
The factory setting is 1600 Nm.
This corresponds to a setting of L = 128 mm.
Dismantling the cam clutch
- Only dismantle clutch when locking cam is engaged
(E).
- Note fitting position of locking cam (SN) when
dismantling.
- Remove spring bolt (F).
Take note!
Both compression springs on the spring bolt must be
equally tensioned firmly.

0000-gb WarTung_877
GB
- 12 -
MaiNTENaNCE aND sErViCE
Advice for general maintence
In order to keep the implement in good condition even after a
longer service life, please observe the following advice.
Safety points
• Turn engine off when
adjustment, service
and repair work is to be
done.
• Do not work under the
machine without safe
support.
- Retighten all screws after the first hours of operation.
- Observe maintenance advice for spur wheel - angular gear.
- The spur wheel gear in the rotor bar is maintenance free.
Cleaning of machine parts
Attention! Do not use high-pressure washers for the cleaning of
bearing- and hydraulic parts.
- Danger of rust!
- After cleaning, grease the machine according to the lubrication
chart and carry out a short test run.
- Cleaning with too high pressure may do damage to varnish.
Winter storage
- Thoroughly clean the machine beforehand.
- Park where protected against weather.
- Change or top-up gear oil.
- Protect all exposed sections against rust.
- Grease all greasing points according to lubrication chart.
- Do not park the machine in high waved position (transport
position)
Hydraulic unit
Caution! Danger of injury or infection!
Under high pressure, escaping fluids can penetrate the skin.
Therefore seek immediate medical help!
Afterthefirst10operatinghoursandtheneveryconsecutive
50 operating hours
- Check the hydraulic unit and lines for tightness and retighten
screw connections if necessary.
Before operation
- Check hydraulic hoses for wear.
Replace worn or damaged hydraulic hoses immediately. The
replacement hoses must meet the manufacturer’s technical
requirements.
Important montage hint
The bearing axes (F) must be mounted aligned at the gears.

0000-gb WarTung_877
GB
MaiNTENaNCE aND sErViCE
- 13 -
Spur wheel - angular gear
- First oil change is after 50 hours of operation.
- Further oil change after 500 hours of operation.
Note:
• Change oil when at operating temperature.
The oil is too viscid when cold. Too much old oil remains stuck
to the gearwheels and because of this any suspended matter
present cannot be removed from the gearing.
Attention combustion danger!
• hot gear
• hot oil
- Check oil level before putting into
operation.
Oil level check
- Park machine horizontally.
L = Ventilating screw:
is removed to enable oil filling.
N = Level screw:
oil level is correct when it reaches the same level as the
screw.
A = Drain plug.
Change speed transmission (middle position)
Amount of oil: 6,5 Liter SAE 90
Angular gears (left and right)
Amount of oil: 4 Liter SAE 90
Changing the tines
Damaged or worn rotor tines are to be replaced. Observe the
correct fitting position of each rotor tine (see Spare Parts list).
Both screws (SK) are to be glued into place with Loctite 243 or
another equivalent product, and tightened to 290 Nm (29 kpm).
Greasing
Drive shaft
- Lubricate drive shaft every 40 hours of operation.
- Take sliding sections apart and grease well.
Greasing positions
- after 30 operating hours greases.
FETT

9900 LEGENDE-SCHMIERPL / BA/EL ALLG / BETRIEBSSTOFFVORSCHRIFT - 14 -
Smøreplan
8hHver 8. driftstime
20hHver 20. driftstime
40 F Hvert 40. læs
80 F Hvert 80. læs
1 J 1 gang årligt
100 ha For hver 100 hektar
FETT Fedt
= Antal smørenipler
(IV) Se smørediagrammet
Liter Liter
* Udstyrsvariant
Se producentens anvisninger
Schmierplan
8halle 8 Betriebsstunden
20halle 20 Betriebsstunden
40 F alle 40 Fuhren
80 F alle 80 Fuhren
1 J 1 x jährlich
100 ha alle 100 Hektar
FETT FETT
= Anzahl der Schmiernippel
(IV) Siehe Anhang "Betriebsstoffe"
Liter Liter
* Variante
Siehe Anleitung des Herstellers
Smeerschema
8halle 8 bedrijfsuren
20halle 20 bedrijfsuren
40 F alle 40 wagenladingen
80 F alle 80 wagenladingen
1 J 1 x jaarlijks
100 ha alle 100 hectaren
FETT VET
= Aantal smeernippels
(IV) Zie aanhangsel "Smeermiddelen"
Liter Liter
* Varianten
zie gebruiksaanwijzing van de fabrikant
Schema di lubrificazione
8hogni 8 ore di esercizio
20hogni 20 ore di esercizio
40 F ogni 40 viaggi
80 F ogni 80 viaggi
1 J volta all'anno
100 ha ogni 100 ettari
FETT GRASSO
= Numero degli ingrassatori
(IV) vedi capitolo “materiali di esercizio”
Liter litri
* variante
vedi istruzioni del fabbricante
Plan de graissage
8hToutes les 8 heures de service
20hToutes les 20 heures de service
40 F Tous les 40 voyages
80 F Tous les 80 voyages
1 J 1 fois par an
100 ha tous les 100 hectares
FETT GRAISSE
= Nombre de graisseurs
(IV) Voir annexe "Lubrifiants"
Liter Litre
* Variante
Voir le guide du constructeur
Lubrication chart
8hafter every 8 hours operation
20hafter every 20 hours operation
40 F all 40 loads
80 F all 80 loads
1 J once a year
100 ha every 100 hectares
FETT GREASE
= Number of grease nipples
(IV) see supplement "Lubrificants"
Liter Litre
* Variation
See manufacturer’s instructions
FETT
Esquema de lubricación
8hCada 8 horas de servicio
20hCada 20 horas de servicio
40 F Cada 40 viajes
80 F Cada 80 viajes
1 J 1 vez al año
100 ha Cada 100 hectáreas
FETT LUBRICANTE
= Número de boquillas de engrase
(IV) Véase anexo “Lubrificantes”
Liter Litros
* Variante
Véanse instrucciones del fabricante
Plano de lubrificação
8hEm cada 8 horas de serviço
20hEm cada 20 horas de serviço
40 F Em cada 40 transportes
80 F Em cada 80 transportes
1 J 1x por ano
100 ha Em cada100 hectares
FETT Lubrificante
= Número dos bocais de lubrificação
(IV) Ver anexo ”Lubrificantes"
Liter Litro
* Variante
Ver instruções do fabricante
Smörjschema
8hVarje 8:e driftstimme
20hVarje 20:e driftstimme
40 F Varje 40: e lass
80 F Varje 80: e lass
1 J 1 x årligen
100 ha Varje 100:e ha
FETT FETT
= Antal smörjnipplar
(IV) Se avsnitt ”Drivmedel”
Liter liter
* Utrustningsvariant
Se tillverkarens anvisningar
Smøreplan
8hHver 8. arbeidstime
20hHver 20. arbeidstime
40 F Hvert 40. lass
80 F Hvert 80. lass
1 J 1 x årlig
100 ha Totalt 100 Hektar
FETT FETT
= Antall smørenipler
(IV) Se vedlegg "Betriebsstoffe"
Liter Liter
* Unntak
Se instruksjon fra produsent
Voitelukaavio
8h8 käyttötunnin välein
20h20 käyttötunnin välein
40 F 40 kuorman välein
80 F 80 kuorman välein
1 J kerran vuodessa
100 ha 100 ha:n välein
FETT RASVA
= Voitelunippojen lukumäärä
(IV) Katso liite ”Polttoaineet”
Liter Litraa
* Versio
Katso valmistajan ohjeet
DKFIN
I P
NL S N
D GBF
E

- 15 -
0000 scHMIErpLan_873

0800-gb TEcH. DaTEn_877
GB
- 16 -
TEChNiCaL DaTa
Optional equipment
Rear deflector
Track loosener (4 pieces)
Lighting set
Technical data
LION 6000
(Type 6000)
1,5 m
-
-
1,4 m
6,0 m
< 3 m
20
25 / 29 cm
199 kW (270 PS)
1000 min-1 (U/min)
2270 kg
3290 kg
<70 dB(A)
Necessary connections
• 1 double-action hydraulic connection
pressure min.: 160 bar
pressure max.: 210 bar
• 7-pole electric connection for lighting (12 Volt)
Subjecttoalterationsdue totechnical
advancement without notice.
Length:
With packer roller
Cage drum roller
Spiral roller
Height (approx)
Working width
Transporting width
No. of rotors
Working depth/Tine length
Requisite power
max.
Drive r.p.m.
Weight – basic implement
Coupled with packer roller 500 mm
ø (approx)
Permanent sound emission level
LION 5000
(Type 5000)
1,5 m
-
-
1,4 m
5,0 m
< 3 m
16
25 / 32 cm
199 kW (270 PS)
1000 min-1 (U/min)
2090 kg
3200 kg
<70 dB(A)
Subject to alterations due to technical
advancement without notice.
Length:
With packer roller
Cage drum roller
Spiral roller
Height (approx)
Working width
Transporting width
No. of rotors
Working depth/Tine length
Requisite power
max.
Drive r.p.m.
Weight – basic implement
Coupled with packer roller 500 mm ø
(approx)
Permanent sound emission level

0800-gb TEcH. DaTEn_877
GB
TEChNiCaL DaTa
- 1 -
Location of Identification Plate
The serial number (Masch.Nr. / Fzg.Ident.Nr.) is struck into the Vehicle Identification
Plate shown opposite, and into the frame. Guarantee claims and queries cannot be
processed without the serial number being given.
Please enter the number on the title page of the operating manual immediately upon
taking possession of the vehicle/implement.
The Defined Use of the Rotary Harrow
The "LION" Rotary Harrow is intended for normal use in agricultural work.
• To prepare the top layer of arable land for sowing afterwards.
Any other uses are regarded as not included in this definition. The manufacturer takes no responsibility for any resulting damage which
occurs henceforth.
The risk is carried solely be the user.
• The keeping of operating, service and maintenance requirements layed down by the manufacturer also come under the heading of „defined
use“.

GB-Anhang Titelblatt _BA-Allgemein
GB
sUppLEMENT

GB-Anhang Titelblatt _BA-Allgemein
GB
The decision must be made, ”original” or ”imitation”? The decision is often governed
by price and a ”cheap buy” can sometimes be very expensive.
Be sure you purchase the ”Original” with the cloverleaf sym-
bol!
• Quality and precise fitting
- Operating safety.
• Reliable operation
• Longer lasting
- Economy
• Guaranteed availability through your
Pöttinger Sales Service.
Things will run better with
genuine Pöttinger parts
The original cannot be copied ...

9400_GB-Anhang A_Sicherheit
sUppLEMENT - a
Recommendations for work safety
- A 1 -
20%
Kg
Recommendations for work safety
All points refering to safety in this manual are indicated
by this sign.
1.)Defined use
a. See "Technical Data".
b. The keeping of operating, service and maintenance requirements
layed down by the manufacturer also come under the heading of
"defined use".
2.) Spare parts
a. The original components and accessories have been designed
especially for these machines and appliances.
b. We want to make it quite clear that components and accesories
that have not been supplied by us have not been tested by us.
c. The installation and/or use of such products can, therefore,
negatively change or influence the construction characteristics
of the appliance. We are not liable for damages caused by the
use of components and accessories that have not been supplied
by us.
d. Alterations and the use of auxiliary parts that are not permitted
by the manufacturer render all liability invalid.
3.) Protection devices
All protection devices must remain on the machine and be
maintained in proper condition. Punctual replacement of worn
and damaged covers is essential.
4.) Before starting work
a. Before commencing work, the operator must be aware of all
operating devices and functions. The learning of these is too late
after having already commenced operation!
b. The vehicle is to be tested for traffic and operating safety before
each operation.
5.) Asbestos
- Certain sub-supplied components of the
vehicle may contain asbestos due to technical
reasons. Observe the warning on spare
parts.
6.) Transport of persons prohibited
a. The transport of persons on the machine is not permitted.
b. The machine may only be driven on public roads when in the
position stipulated for road transport.
7.) Driving ability with auxiliary equipment
a. The towing vehicle is to be sufficiently equiped with weights at the
front or at the rear in order to guarantee the steering and braking
capacity (a minimum of 20% of the vehicle’s tare weight on the
front axle).
b. The driving ability is
influenced by ground
conditions and by the
auxiliary equipment. The
driving must be adapted
to the corresponding
terrain and ground
conditions.
c. When driving through
curves with a connected
appliance, observe the
radius and swinging
mass of the appliance.
d. When travelling in a curve with attached or semimounted
implements, take into account the working range and swing mass
of the implement!
8.) General
a. Before attaching implement to three-point linkage, move system
lever into a position whereby unintentional raising or lowering is
ruled out!
b. Danger of injury exists when coupling implement to tractor!
c. Danger of injury through crushing and cutting exists in the three-
point linkage area!
d. Do not stand between tractor and implement when using three-
point linkage external operation!
e. Attach and detach drive shaft only when motor has stopped.
f. When transporting with raised implement, secure operating lever
against lowering!
g. Before leaving tractor, lower attached implement to the ground
and remove ignition key!
h. Nobody is to stand between tractor and implement without tractor
being secured against rolling using parking brake and/or wheel
chocks!
i. For all maintenance, service and modification work, turn driving
motor off and remove universal drive.
9.) Cleaning the machine
Do not use high-pressure washers for the cleaning of bearing- and
hydraulic parts.