Power Electronics SDRIVE 700 Series Parts list manual

Getting Started Manual
variable speed drive

variable speed drive
Getting Started Manual
Edition: March 2007
SD70IM01BI Rev. B

SDRIVE 700 POWER ELECTRONICS
2

POWER ELECTRONICS SDRIVE 700
3
SAFETY SYMBOLS
Always follow safety instructions to prevent accidents and potential hazards from occurring.
Edition of March 2007
This publication could present technical imprecision or misprints. The information here included will be
periodically modified and updated, and all those modifications will be incorporated in later editions.
To consult the most updated information of this product you might access through our website
www.power-electronics.com where the latest version of this manual can be downloaded.
Revisions
Date Revision Description
01 / 03 / 2006 A Updated software version SW Ver 1.02
16 / 03 / 2007 B Drawings and misprints updating. New frames.
Frames updating.
Software updating (2) to Software version 1.3
WARNING This symbol means improper operation may results in serious personal
injury or death.
CAUTION Identifies shock hazards under certain conditions.Particular attention should
be given because dangerous voltage may be present. Maintenance
operation should be done by qualified personnel
Identifies potential hazards under certain conditions. Read the message and
follow the instructions carefully.
Identifies shock hazards under certain conditions.Particular attention should
be given because dangerous voltage may be present.

SDRIVE 700 POWER ELECTRONICS
4

POWER ELECTRONICS SDRIVE 700
INDEX 5
INDEX
SAFETY INSTRUCTIONS........................................................................................................... 7
1. INTRODUCTION .................................................................................................................. 11
1.1. Designation Code....................................................................................................... 11
1.2. Drive Description........................................................................................................ 12
2. INSTALLATION AND CONNECTION.................................................................................. 13
2.1. Basic Configuration.................................................................................................... 13
2.2. Environmental Conditions.......................................................................................... 14
2.3. Drive Mounting........................................................................................................... 14
2.4. Power Connection and Control Wiring....................................................................... 14
3. POWER RANGE.................................................................................................................. 16
3.1. Power Range at 400Vac............................................................................................ 16
3.2. Power Range at 500Vac............................................................................................ 17
4. TECHNICAL CHARACTERISTICS...................................................................................... 18
5. DIMENSIONS....................................................................................................................... 20
5.1. Dimensions of Frames 3, 4 and 5 .............................................................................. 20
5.2. Dimensions of Frames 6 and 7 .................................................................................. 21
5.3. Dimensions of Frames 8 and 9 .................................................................................. 22
5.4. Dimensions of Frames 10 and 11.............................................................................. 23
5.5. Dimensions of Frames 4 and 5 IP00.......................................................................... 24
5.6. Dimensions of Frames 6 and 7 IP00.......................................................................... 25
6. CONNECTION TERMINALS................................................................................................ 26
6.1. Power Connections.................................................................................................... 26
6.2. Control Connections................................................................................................... 32
6.3. Control Terminals Description.................................................................................... 34
7. DISPLAY UNIT AND CONTROL KEYPAD.......................................................................... 35
7.1. Keypad Unit Description............................................................................................. 35
8. STATUS MESSAGES.......................................................................................................... 38
8.1. List of Status Messages............................................................................................. 38
8.2. List of Warning Messages.......................................................................................... 39
9. VISUALIZATION AND STATUS PARAMETERS. GROUP G0 ........................................... 40
9.1. Parameters SV.1 – Motor Visualization...................................................................... 40
9.2. Parameters SV.2 – Drive Visualization ...................................................................... 41
9.3. Parameters SV.3 – External Visualization.................................................................. 41
9.4. Parameters SV.4 – Internal Visualization................................................................... 42
9.5. Parameters SV.5 – Programmable Parameters......................................................... 42
9.6. Parameters SV.8 – Pump Control.............................................................................. 43
10. DESCRIPTION OF PROGRAMMING PARAMETERS ........................................................ 45
10.1. Group 1 – G1: Options Menu..................................................................................... 45
10.2. Group 2 – G2: Motor Nameplate Data ....................................................................... 47
10.3. Group 3 – G3: References......................................................................................... 47
10.4. Group 4 – G4: Inputs.................................................................................................. 48
10.5. Group 5 – G5: Acceleration and Deceleration Ramps ............................................... 56
10.6. Group 6 – G6: PID Control......................................................................................... 57
10.7. Group 7 – G7: Start / Stop Mode Configuration ......................................................... 58
10.8. Group 8 – G8: Outputs............................................................................................... 60
10.9. Group 9 – G9: Comparators....................................................................................... 64
10.10. Group 10 – G10: Limits.............................................................................................. 68
10.11. Group 11 – G11: Protections ..................................................................................... 69
10.12. Group 12 – G12: Auto Reset...................................................................................... 71

SDRIVE 700 POWER ELECTRONICS
6 INDEX
10.13. Group 13 – G13: Fault History................................................................................... 73
10.14. Group 14 – G14: Multi-references.............................................................................. 74
10.15. Group 15 – G15: Inch Speeds ................................................................................... 74
10.16. Group 16 – G16: Skip Frequencies............................................................................ 74
10.17. Group 17 – G17: Brake.............................................................................................. 75
10.18. Group 19 – G19: Fine Tuning .................................................................................... 76
10.19. Group 20 – G20: Serial Communication Controls...................................................... 78
10.20. Group 25 – G25: Pump Control ................................................................................. 80
11. FAULT MESSAGES. DESCRIPTION AND ACTIONS ........................................................ 98
11.1. Description of Faults List............................................................................................ 98
11.2. Procedure for Fault Solutions..................................................................................... 100
11.3. Maintenance .............................................................................................................. 103
12. COMMONLY USED CONFIGURATIONS............................................................................ 105
12.1. Start / Stop Commands and Speed Reference by Keypad........................................ 105
12.2. Start / Stop Commands by Terminals and Speed Reference by
Analogue Input........................................................................................................... 105
12.3. Start / Stop Commands by Terminals and Speed Reference by
Motorized Potentiometer............................................................................................ 107
12.4. Start / Stop Commands by Terminals and Seven Speed References
Selectable by Digital Inputs........................................................................................ 108
12.5. Pressure Group Control with 3 Auxiliary Pumps, Start and Stop on Demand............ 109
12.6. Pressure Group Control with Eight Pressure References.......................................... 112
13. CONFIGURATION REGISTER............................................................................................ 115

POWER ELECTRONICS SDRIVE 700
SAFETY INSTRUCTIONS 7
SAFETY INSTRUCTIONS
IMPORTANT!
Read this manual carefully to maximise the performance of this product and to ensure its safe use.
In this manual, safety messages are classified as follows:
WARNING
Do not remove the cover while the power is applied or the unit is in operation.
Otherwise electric shock could occur.
Do not run the drive with the front cover removed. Otherwise you may get an electric
shock due to the high voltage terminals or exposure of charged capacitors.
Do not remove the cover except for periodic inspections or wiring, even if the
input power is not applied. Otherwise you may access the charged circuits and get an
electric shock.
Wiring and periodic inspections should be performed at least 10 minutes after
disconnecting the input power and after checking the DC Link voltage is
discharged with a meter (below 30VDC).
Otherwise you may get an electric shock.
Operate the switches with dry hands.
Otherwise you may get an electric shock.
Do not use cables with damaged insulation.
Otherwise you may get an electric shock.
Do not subject the cables to abrasions, excessive stress, heavy loads or pinching.
Otherwise, you may get an electric shock.

SDRIVE 700 POWER ELECTRONICS
8 SAFETY INSTRUCTIONS
CAUTION
Install the drive on a non-flammable surface. Do not place flammable material
nearby. Otherwise fire could occur.
Disconnect the input power if the drive gets damaged. Otherwise it could result in a
secondary accident or fire.
After the input power is applied or removed, the drive will remain hot for a couple
of minutes. Touching hot parts may result in skin burns.
Do not apply power to a damaged drive or to a drive with parts missing even if the
installation is complete. Otherwise you may get an electric shock.
Do not allow lint, paper, wood chips, dust, metallic chips or other foreign matter
into the drive. Otherwise fire or accident could occur.
WARNINGS
RECEPTION
The SDRIVE 700 is carefully tested and perfectly packed before leaving the
factory.
In the even of transport damage, please ensure that you notify the transport
agency and POWER ELECTRONICS: 902 40 20 70 (International [phone]
57) or your nearest agent, within 24hrs from receipt of the goods.
UNPACKING
Make sure model and serial number of the variable speed drive are the same on
the box, delivery note and unit.
Each variable speed drive is supplied with a SDRIVE 700 technical manual.

POWER ELECTRONICS SDRIVE 700
SAFETY INSTRUCTIONS 9
SAFETY
Before operating the drive, read this manual thoroughly to gain and understanding
of the unit. If any doubt exists then please contact POWER ELECTRONICS, (902
40 20 70 / [phone]) or your nearest agent.
Wear safety glasses when operating the drive with power applied and the front
cover is removed.
Handle the drive with care according to its weight.
Install the drive according to the instructions within this manual.
Do not place heavy objects on the drive.
Ensure that the mounting orientation is correct.
Do not drop the drive or subject it to impact.
The SDRIVE 700 drives contain static sensitive printed circuits boards. Use static
safety procedures when handling these boards.
Avoid installing the drive in conditions that differ from those described in the
Technical Characteristics section.
CONNECTION PRECAUTIONS
To ensure correct operation of the drive it is recommended to use a SCREENED
CABLE for the control wiring.
For EMERGENCY STOP, make sure supply circuitry is open.
Do not disconnect motor cables if input power supply remains connected. The
internal circuits of the SDRIVE 700 series will be damaged if the incoming power
is connected and applied to output terminals (U, V, W).
It is not recommended to use a 3-wire cable for long distances. Due to increased
leakage capacitance between conductors, over-current protective feature may not
operate correctly.
Do not use power factor correction capacitors, surge suppressors, or RFI filters on
the output side of the drive. Doing so may damage these components.
Always check whether the DC Link LED is OFF before wiring terminals. The
capacitors may hold high-voltage even after the input power is disconnected. Use
caution to prevent the possibility of personal injury.
TRIAL RUN
Verify all parameters before operating the drive. Alteration of parameters may be
required depending on application and load.
Always apply voltage and current signals to each terminal that are within levels
indicated within this manual. Otherwise, damage to the drive may result.

SDRIVE 700 POWER ELECTRONICS
10 SAFETY INSTRUCTIONS
OPERATION PRECAUTIONS
When the Auto Restart function is enabled, keep clear of driven equipment, as the
motor will restart suddenly after a fault is reset.
The “STOP / RESET” key on the keypad is active only if the appropriate function
setting has been made. For this reason, install a separate EMERGENCY STOP
push button that can be operated at the equipment.
If a fault reset is made with the reference signal still present then a restart will
occur. Verify that it is permissible for this to happen, otherwise an accident may
occur.
Do not modify or alter anything within the drive.
Before programming or operating the SDRIVE 700 series, initialise all parameters
back to factory default values.
EARTH CONNECTION
The drive is a high frequency switching device and leakage current may flow.
Ground the drive to avoid electrical shock. Use caution to prevent the possibility of
personal injury.
Connect only to the dedicated ground terminal of the drive. Do not use the case or
the chassis screw for grounding.
When installing, grounding wire should be connected first and removed last.
The earth cable must have a minimal cross sectional area that meets local
country electrical regulations.
Motor ground must be connected to the drive ground terminal and not to the
installation’s ground. We recommend that the section of the ground connection
cable should be equal or higher than the active conductor.
Installation ground must be connected to the drive ground terminal.

POWER ELECTRONICS SDRIVE 700
INTRODUCTION 11
1. INTRODUCTION
1.1. Designation Code
SD 7 0115 5 2 1 12
* In case of 230Vac power supply, consult availability with Power Electronics.
CODE PULSE NUMBER
- 6 Pulses
12 12 Pulses
18 18 Pulses
CODE FILTER
1 First environment filter
2 Second environment filter
CODE PROTECTION DEGREE
0 IP00 Degree protection
2 IP20 Degree protection
5 IP54 Degree protection
CODE POWER SUPPLY
5* 380 – 500Vac
6 690Vac
CODE CURRENT
115 115A
330 330A
… …A
CODE MODEL
7 700
CODE SERIES
SD SDRIVE

SDRIVE 700 POWER ELECTRONICS
12 INTRODUCTION
1.2. Drive description
The SDRIVE700 is a UNIQUE drive:
¾Due to its mechanical design.
FFA (Full Frontal Access) has reached an important objective: to make easy, in a
significant way, its installation and maintenance thanks to its modular independence. It is
available in IP00, IP20 and IP54.
¾Due to features.
First speed drive incorporating a Graphical Display with 3.5" TFT touch screen for fast
and easy programming.
oReal time clock and perpetual calendar.
oUSB 2.1 Communication Port.
oFibre Optic Port.
¾Due to its reliability.
FPA (Fault Preventing Algorithms) is able to detect critical situations and correct them
avoiding unnecessary downtime in production. Power Electronics has employed a new
control strategy: MCA (Motion Combined Algorithms) combining all the advantages of
different traditional motor control and ensuring robustness and stability.
1. Removable Display
2. Control Terminals
3. Power Terminals
1
2
3

POWER ELECTRONICS SDRIVE 700
INSTALLATION AND CONNECTION 13
2. INSTALLATION AND CONNECTION
2.1. Basic Configuration
The following devices are required to operate the drive. Proper peripheral devices must be selected
and correct connections must be done to ensure proper operation. An incorrectly applied or installed
drive can result in system malfunction or reduction in product life as well as component damage. You
must read and understand this manual thoroughly before proceeding.
AC Power
Supply
Use a power source with a voltage within the permissible range
of drive input power rating. Equipment is provided to operate
with the neutral connected to the ground.
Earth leakage
circuit breaker
(ELB)
Select circuit breakers or fuses in accordance with applicable
national and local codes. We recommend using specified circuit
breakers or fuses to operate with drive.
Inline Magnetic
Contactor
Install if necessary. When installed, do not use it for the purpose
of starting or stopping the drive.
Installation and
wiring
To reliably operate the drive, install the drive in the proper
orientation and with proper clearances. Incorrect terminal wiring
could result in the equipment damage.
Motor
Do not connect power factor capacitors, surge arrestors or radio
noise filters to the output side of the drive.

SDRIVE 700 POWER ELECTRONICS
14 INSTALLATION AND CONNECTION
2.2. Environmental Conditions
Verify ambient conditions of mounting location.
Ambient temperature should not be below -30ºC or exceed 50ºC. It is necessary to consider the use
of the equipment according to normal duty or heavy duty. It is recommended to consult the tables of
standard types included in this manual to guarantee correct use of the equipment.
Relativity humidity should be less than 95% (non-condensing).
Altitude should be below 1.000m (3.300ft).
SD700 is offered with IP00, IP20 and IP54 protection degree. Nevertheless, we recommend
protecting it from conductive dust (dry or wet) and water drops. As an electronic device, the SD700
will have a longer life if the installation is done properly in a clean place, with a correct ventilation
system and protected from mechanical vibrations.
2.3. Drive Mounting
SD700 should be mounted vertically. It should be well fastened through the anchorages designed for
this to avoid any movement.
If the drive is installed inside a cabinet the heated air must be vented out of the cabinet to ensure
correct cooling. To avoid such a situation it is also necessary to leave enough horizontal and vertical
space with any adjacent equipment.
We recommend cooling the cabinet to evacuate dissipated heat.
2.4. Power Connection and Control Wiring
2.4.1. Power Wiring
Input terminals (drive supply) and output terminals (motor supply) are accessible from the bottom.
SD700 is designed for working with 3-phase supply with the neutral connected to the earth.
It is not necessary to use power factor correction capacitors at the SD700 input, and do not
connect them to the output of the drive.
Line voltage should be connected to L1, L2 and L3 terminals, and earth will be connected to the
terminals assigned for this function.
Motor should be connected to the terminals indicated as U, V and W.
Figure 2.1 Power Connection Detail

POWER ELECTRONICS SDRIVE 700
INSTALLATION AND CONNECTION 15
We recommend installing the drive according to the following connection:
Figure 1.2 Power wiring connection
Note: It is recommended to use an earth cross section equal or higher than active wires cross section.
CAUTION
Line voltage must never be connected to U, V and W terminals. Otherwise the drive will be
damaged.
2.4.2. Control Wiring
Control wiring should be installed as far as possible from the power wiring. If you have to pass the
control wiring next to the power wiring it should do perpendicularly. The cable should be screened
and the shield should be connected to ground.
Do not use voltages of 24Vdc and 220Vac into the same cable.
2.4.3. Observations before Trial Run
Before applying voltage, we recommended to check that the power wiring is connected correctly
and to verify that the connections are correctly fastened.
It is recommended to close the doors of SD700 before applying voltage the first time.
Before applying voltage to the drive and configuring it, make sure the line voltage is compatible
with drive power supply. On the contrary, the drive will be damaged.
After applying voltage to the drive, verify the display is turned on and the status led of the DC bus
is also illuminated.
Check line voltages when the display is lit. If the drive does not read one of the 3 phases then
check input power wiring.
Before starting the SD700, the parameters should be programmed correctly for proper operation
of the motor. Ensure the correct motor parameters are entered before giving the first “start”
command to the drive.
WARNING
It is absolutely necessary that the installer guaranties the correct observance of the law and the
regulations that are in force in those countries or areas where this device is going to be installed.
GL1
(R) L2 (S)
SD70DTP0003AI
L3
(T) U V W
INPUT POWER SUPPLY
3 PHASE + PE, 380-480Vac
50/60Hz
G

SDRIVE 700 POWER ELECTRONICS
16 POWER RANGE
3. POWER RANGE
3.1. Power Range at 400Vac
Operation Temperature 50ºC
HEAVY DUTY Operation Temperature 40ºC HEAVY DUTY
FRAME CODE I(A) Rated Power (kW)
at 400Vac 150% Overload I(A) Rated Power (kW) at 400Vac 120% Overload
SD70006 5x x xx 6 2,2 9 7,5 3 9
SD70007 5x x xx 7,5 3 11 9,4 4 11
SD70009 5x x xx 9 4 14 11 5,5 14
SD70012 5x x xx 12 5,5 18 15 7,5 18
SD70018 5x x xx 18 7,5 27 23 11 27
1
SD70024 5x x xx 24 11 36 30 15 36
SD70032 5x x xx 32 15 48 40 18,5 48
SD70038 5x x xx 38 18,5 57 48 22 57
2
SD70048 5x x xx 48 22 72 60 30 72
SD70060 5x x xx 60 30 90 75 37 90
SD70075 5x x xx 75 37 113 94 45 113
SD70090 5x x xx 90 45 135 113 55 135
3
SD70115 5x x xx 115 55 173 144 75 173
SD70150 5x x xx 150 75 225 188 90 225
4 SD70170 5x x xx 170 90 255 213 110 255
SD70210 5x x xx 210 110 315 263 132 315
SD70250 5x x xx 250 132 375 313 160 375
5
SD70275 5x x xx 275 150 413 344 200 426
SD70330 5x x xx 330 160 495 413 220 495
SD70370 5x x xx 370 200 555 463 250 555
6
SD70460 5x x xx 460 250 690 575 315 690
SD70580 5x x xx 580 315 870 725 400 870
SD70650 5x x xx 650 355 975 813 450 975
7
SD70720 5x x xx 720 400 1080 900 500 1080
SD70840 5x x xx 840 450 1260 1050 560 1260
8 SD70925 5x x xx 925 500 1388 1156 630 1388
SD71030 5x x xx 1030 560 1545 1288 710 1545
SD71150 5x x xx 1150 630 1725 1438 800 1725
SD71260 5x x xx 1260 710 1890 1575 900 1890
9
SD71440 5x x xx 1440 800 2160 1800 1000 2160
SD71580 5x x xx 1580 900 2370 1975 1100 2370
10 SD71800 5x x xx 1800 1000 2700 2250 1200 2700
11 SD72200 5x x xx 2200 1200 3300 2750 1500 3300
Table 3.1 Table of power and current data at 400V
NOTES:
Rated power for standard A.C. motors of 4-pole (1500rpm).
For higher power units contact Power Electronics.
The motor nameplate must be checked to ensure that the selected variable speed drive is correct
for each specific motor.

POWER ELECTRONICS SDRIVE 700
POWER RANGE 17
3.2. Power Range at 690Vac
Operation Temperature 50ºC
HEAVY DUTY Operation Temperature 40ºC HEAVY DUTY
FRAME CODE I(A) Rated Power (kW)
at 690Vac 150% Overload I(A) Rated Power (kW) at 690Vac 120% Overload
SD70052 6x x xx 52 45 78 65 55 78
SD70062 6x x xx 62 55 93 78 75 93
3
SD70080 6x x xx 80 75 120 100 90 120
4 SD70105 6x x xx 105 90 157 131 110 157
SD70130 6x x xx 130 110 195 163 132 195
SD70150 6x x xx 150 132 225 188 160 225
5
SD70170 6x x xx 170 160 255 213 200 255
SD70210 6x x xx 210 200 315 263 250 315
SD70260 6x x xx 260 250 390 325 315 390
6
SD70320 6x x xx 320 315 480 400 355 480
SD70385 6x x xx 385 355 578 481 450 578
7 SD70460 6x x xx 460 450 690 575 500 690
SD70550 6x x xx 550 500 825 688 630 825
8 SD70660 6x x xx 660 630 990 825 800 990
SD70750 6x x xx 750 710 1125 938 900 1125
SD70840 6x x xx 840 800 1260 1050 1000 1260
9
SD70950 6x x xx 950 900 1425 1188 1100 1425
SD71140 6x x xx 1140 1000 1710 1425 1300 1710
SD71270 6x x xx 1270 1200 1905 1588 1600 1905
10
SD71420 6x x xx 1420 1400 2130 1775 1700 2130
SD71500 6x x xx 1500 1500 2250 1875 1800 2250
11 SD71800 6x x xx 1800 1800 2700 2250 2000 2700
Table 3.2 Table of power and current data at 690V
NOTES:
Rated power for standard A.C. motors of 4-pole (1500rpm).
For higher power units contact Power Electronics.
The motor nameplate must be checked to ensure that the selected variable speed drive is correct
for each specific motor.

SDRIVE 700 POWER ELECTRONICS
18 TECHNICAL CHARACTERISTICS
4. TECHNICAL CHARACTERISTICS
Power supply 380-500Vac, 550-690Vac (-20% to +10%) 3-Phase
230Vac optional*
Input frequency 48 a 62 Hz
Input current ≤Output current
Input power factor ≥0.98 (of fundamental)
Power factor ≤0.88
Momentary power loss > 2sec (depending on the load)
EMC input filter Second environment, limits 3 and 4
First environment, limit 1 and 2 optional built in
INPUT
Harmonics filter Choke coils 3% impedance
Motor output voltage 0Vac to 100% Input voltage
Output frequency 0 to ±250%
Overload capacity 150% during 60sec at 50ºC
Efficiency (at full load) >97%
Motor power (kW) 50 to 150% of SD700 rating
Motor voltage 5 to 500Vac
Control method Vector control without encoder (Sensorless, open loop).
Vector Control and V/Hz
Carrier frequency 4 to 8kHz – PEWave
Output dV/dt filter 500 to 800V/µs (according to SD700 rating)
OUTPUT
Output cable length Maximum 300 meters**
Ambient temperature Minimum: -30°C Maximum: +50°C
Altitude 1000m
Altitude de-rating >1000m, 1% per 100m; 3000m maximum
Degree protection IP00, IP20 and IP54
Ambient humidity <95%, non-condensing
ENVIRONMENTAL
CONDITIONS
Display degree protection IP54
Rotor locked
Motor overload (thermal model)
Phase current imbalance, phase voltage imbalance
Motor over-temperature (PTC, normal status 85R – 2kΩ)
Speed limit
MOTOR
PROTECTIONS
Torque limit
Output current limit
Overload
IGBT's overload
Input phase loss
Low input voltage, High input voltage
DC Bus voltage limit
Low DC Bus voltage
High input frequency
Low input frequency
IGBT temperature
Heat-sink over-temperature
Power supply fault
Drive thermal model
Ground fault
Software and Hardware fault
DRIVE
PROTECTIONS
Analogue input signal loss (speed reference loss)
6 programmable inputs, active high (24Vdc)
1 PTC input:
“1” logic = PTC resistance < than 1K5 (ambient temperature)
“0” logic = PTC resistance > than 4K7 (high temperature)
1 programmable digital input (controlled by jumper, a fault is generated when it is disconnected, to avoid dangerous
situations during programming)
DIGITAL INPUTS
Additional features: Isolated power supply
2 programmable and differential inputs. Operation modes:
Current signal: 0 – 20mA, 4 – 20mA.
Voltage signal: 0 – 10Vdc, ±10Vdc, differential
ANALOGUE
INPUTS
Additional features: Optically insulated
* Consult availability with Power Electronics.
** Cable length could be increased depending on cable type. Consult with Power Electronics.

POWER ELECTRONICS SDRIVE 700
TECHNICAL CHARACTERISTICS 19
Optional encoder boards are available for two differential encoders (one available for the user, one available for
vector control mode). Others types of encoders can be used as necessary
ENCODER
INPUTS Additional features:
Voltages inputs from 5 to 24Vdc
DIGITAL
OUTPUTS
3 programmable changeover relays (250Vac, 8A or 30Vdc, 8A)
ANALOGUE
OUTPUTS
2 isolated programmable outputs: 0 – 20mA, 4 – 20mA, 0 – 10Vdc y ±10Vdc
POTENTIOMETER
VOLTAGE
10Vdc power supply voltage for speed reference by potentiometer (26mA maximum)
USER POWER
SUPPLY
24Vdc user power supply regulated and short-circuit protected
From a communication perspective the SD700 will provide:
Standard Hardware: Optional Hardware:
USB Port Optic Fibre
RS232 Port Ethernet
RS485 Port
Software Protocols:
Standard: Optional:
Modbus-RTU Profibus
DeviceNet
TCP/IP
COMMUNICATION
N2 Metasys
Average current and 3-phase motor current
Average voltage and 3-phase motor voltage
Average input voltage and 3-phase input voltage
Speed, Torque, Power, Power factor of motor
Relay status
Digital input status / PTC status
Output comparator status
Value of analogue inputs and sensors
Analogue output value
Motor overload status and drive overload status
IGBT temperature
Motor output frequency
VISUALIZATION
INFORMATION
Fault history (6 last faults)
Local from keypad
Remote from digital inputs
CONTROL
MODES Serial communications
Type Removable
Length 3 meters*
Connection RJ45
Alphanumeric Display 4 lines of 16 characters
Visualization Leds LED ON: Control board is energized
LED RUN: Motor receiving power supply from SD700
LED FAULT: Blinking shows that a fault has occurred
Keypad 6 control keys to program the drive, start and stop/reset.
Provided with independent memory
CONTROL PANEL
Graphic Display Optional graphical display with 3,5" TFT touch screen
Independent memory
Real time clock
OTHERS Perpetual calendar
CERTIFICATION CE, UL, cUL, cTick
* Possibility of increasing length. Consult with Power Electronics.