Powerfix Profi 284621 User manual

PRECISION TOOL HOLDER WITH LED
MAGNIFYING GLASS
PRECISION TOOL HOLDER
WITH LED MAGNIFYING GLASS
Operation and Safety Notes
FINOMMECHANIKAI
MŰSZERÉSZ KÉSZLET LED
NAGYÍTÓVAL
Kezelési és biztonsági utalások
KOMPLET ZA FINOMEHANIKE
Z LED-LUPO
Navodila za upravljanje in varnostna
opozorila
LED LUPA NA JEMNOU
MECHANIKU
Pokyny pro obsluhu a bezpečnostní
pokyny
FEINMECHANIKER-SET
MIT LED-LUPE
Bedienungs- und Sicherheitshinweise
SÚPRAVA NA JEMNÚ
MECHANIKU S LED LUPOU
Pokyny pre obsluhu a bezpečnostné pokyny
IAN 284621

GB Operation and Safety Notes Page 5
HU Kezelési és biztonsági utalások Oldal 18
SI Navodila za upravljanje in varnostna opozorila Stran 31
CZ Pokyny pro obsluhu a bezpečnostní pokyny Strana 46
SK Pokyny pre obsluhu a bezpečnostné pokyny Strana 59
DE/AT/CH Bedienungs- und Sicherheitshinweise Seite 72

1 6 7
8
10
13
14
16
3
2 5
9
15
A
17
11
4
12
18
22
23
20 19
B
20

D
C
13
21
24
13
14 14 14

5GB
Introduction........................................................Page 6
Intended use.............................................................Page 6
Description of parts..................................................Page 7
Technical data..........................................................Page 8
Includes.....................................................................Page 8
Safety......................................................................Page 9
General safety information......................................Page 9
Safety instructions for batteries/
rechargeable batteries.............................................Page 10
Before initial use............................................Page 12
Inserting the batteries...............................................Page 12
Attaching the repair device .....................................Page 13
Mounting the magnifying glass...............................Page 13
Placement of the base..............................................Page 13
Use.............................................................................Page 14
Using the product.....................................................Page 14
Changing the batteries ............................................Page 14
Troubleshooting .............................................Page 15
Cleaning and maintenance...................Page 15
Disposal.................................................................Page 16

6 GB
Precision tool holder with
LED magnifying glass
Introduction
We congratulate you on the purchase of your new
product. You have chosen a high quality product.
The instructions for use are part of the product.
They contain important information concerning safety, use and
disposal. Before using the product, please familiarise yourself
with all of the safety information and instructions for use. Only
use the product as described and for the specified applications.
If you pass the product on to anyone else, please ensure that
you also pass on all the documentation with it.
Intended use
The product is designed for 2.5-/ 5-fold magnification of
objects. The integrated LEDs only serve for better contrast
and shadow-free visualization of the object to be enlarged.
In addition, the product has 2 fixing clamps and a soldering
iron holder. Other uses or changes to the product are consid-
ered to be contrary to the Intended use and may harbour risks
of injury and damage. The manufacturer does not accept any
liability for injury or damage resulting from use of this product
contrary to its Intended use. The product is intended for indoor
use only. The product is not intended for commercial use or
for use in other application.

7GB
Not suitable for ordinary lighting in household
room illumination.
Description of parts
1Precision engineer’s LED magnifying glass
2Lens (magnification 2.5/5 times)
3Battery compartment cover
4Battery compartment
5Ball joint
6Retaining screw (lens ball joint)
7Magnifying glass fixing clamp
8Retaining screw (magnifying glass height adjustment)
9On/off switch
10 Supporting rod (height adjustment)
11 Fixing clamp (repair device)
12 Retaining screw (repair device height adjustment)
13 Soldering iron holder
14 Base
15 Repair device
16 Retaining screw (repair device ball joint)
17 Retaining screw (repair device)
18 Alligator clips
19 Retaining screws (alligator clips)
20 LED lamps (Fig. B)
21 Batteries (Fig. C)
22 Supporting rod (holding Alligator clips)

8 GB
23 Locking screws (tightening Alligator clips)
24 Ribbon (inside battery compartment)
Technical data
Operating voltage: 4.5 volts
Batteries: 3 x 1.5V , AAA type
Max. power rating: 2x 0.06W
Bulbs: 2x LED (not replaceable)
Magnification/
magnifying glass: 2.5/5 times
Dimensions: approx. 20.5 x 12 x 17cm (W x H x D)
Chromaticity
coordinate: X < 0.27 or X > 0.530; Y < -2.3172 X
+ 2.3653 X–0.2199 or Y > -2.3172 X
+ 2.3653 X - 0.1595
Includes
Immediately after unpacking please check the package con-
tents for completeness and if all parts and the product are in
good condition. Do not under any circumstances use the
product if the delivery is incomplete.
1 Precision LED Magnifying Glass
3 Batteries, 1.5V , AAA
1 Operating Instructions

9GB
Safety
General safety information
KEEP ALL THE SAFETY ADVICE AND INSTRUCTIONS IN
A SAFE PLACE FOR FUTURE REFERENCE!
DANGER OF DEATH
AND ACCIDENTS FOR TODDLERS AND
CHILDREN! Never leave children unsupervised
with the packaging material. The packaging material
represents a danger of suffocation. Children frequently
underestimate the dangers. Always keep children away
from the packaging material. This is not a toy.
This product can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge
if they have been given supervision or instruction concern-
ing use of the product in a safe way and understand the
hazards involved. Children shall not play with the prod-
uct. Cleaning and user maintenance shall not be made
by children without supervision.
CAUTION! RISK OF INJURY! Please do not use this
product if you find that it is damaged in any way.
Check whether all of the parts are correctly fitted. If the
product is not correctly assembled there is a danger of
injury.
Keep the product away from humidity.

10 GB
CAUTION! RISK OF EYE INJURIES! Never look
through the product into the sun or other sources of light.
Severe eye injuries may be the result.
CAUTION! DANGER OF FIRE!
Never expose the product to direct sun-
light or other sources of light. Never
leave the product unattended. Other-
wise there is a danger of fire resulting
from concentrated rays of light and concentrated heat.
The product must be stored in a dark environment.
Do not subject the product to any extreme temperatures
or severe mechanical stress. Otherwise this may result in
deformation of the product.
Make sure that the lens 2does not come into contact
with sharp or pointed objects. Otherwise this may result
in damage to the product.
Do not leave the soldering gun (separate device) unat-
tended whilst on. The soldering iron holder 13 is only
suitable for holding the soldering iron for a limited time.
Safety instructions for batteries/
rechargeable batteries
DANGER TO LIFE! Keep batteries/ rechargeable bat-
teries out of reach of children. If accidentally swallowed
seek immediate medical attention.
DANGER OF EXPLOSION! Never re-
charge non-rechargeable batteries. Do not
short-circuit batteries/rechargeable batteries

11GB
and/or open them. Overheating, fire or bursting can be
the result.
Never throw batteries/rechargeable batteries into fire or
water.
Do not exert mechanical loads to batteries/rechargea-
ble batteries.
Risk of leakage of batteries/rechargeable
batteries
Avoid extreme environmental conditions and temperatures,
which could affect batteries/rechargeable batteries, e.g.
radiators/direct sunlight.
Avoid contact with the skin, eyes and mucous membranes.
In the event of contact with battery acid, thoroughly flush
the affected area with plenty of clean water and seek
immediate medical attention.
WEAR PROTECTIVE GLOVES! Leaked or
damaged batteries/rechargeable batteries
can cause burns on contact with the skin.
Wear suitable protective gloves at all times if such an
event occurs.
In the event of a leakage of batteries/ rechargeable
batteries, immediately remove them from the product to
prevent damage.
Only use the same type of batteries/ rechargeable bat-
teries. Do not mix used and new batteries/rechargeable
batteries.
Remove batteries/ rechargeable batteries if the product
will not be used for a longer period.

12 GB
Risk of damage of the product
Only use the specified type of battery/rechargeable
battery!
Insert batteries/rechargeable batteries according to
polarity marks (+) and (-) on the battery/rechargeable
battery and the product.
Clean the contacts on the battery/ rechargeable battery
and in the battery compartment before inserting!
Remove exhausted batteries /rechargeable batteries
from the product immediately.
Before initial use
Note: Remove all packaging materials from the product.
Inserting the batteries (Figure C)
Remove the battery compartment cover 3from the
battery compartment 4by pulling in the direction of
the arrow.
Insert the three batteries supplied 21 into the battery
compartment 4.
Note: Ensure the ribbon 24 is under the batteries and
the batteries with the correct polarity. This is shown in the
battery compartment 4.
Push the battery compartment cover 3in the opposite
direction to the arrow back to its original position in order
to close the battery compartment 4.

13GB
Attaching the repair device
Insert the ball joint of the repair device 15 into the
corresponding recess of the fixing clamp 11 .
Fix the repair device 15 in place by tightening the
fastening screw 16 clockwise.
Tightening the retaining screws 17 in clockwise direction
for holding the supporting rod 22 properly.
Turn the locking screws 23 tightly for fixing the Alligator
clips 18 properly.
Push the fixing clamp 11 onto the mounting rod 10 , set
the desired height and tighten the fastening screw 12
clockwise.
Mounting the magnifying glass
Insert the ball joint 5into the corresponding recess
and tighten the fastening screw 6for the ball joint 5
clockwise (Fig. A).
Push the fixing clamp 7on to the mounting rod 10 and
set the desired height. Tighten the fastening screw 8by
turning it clockwise.
Placement of the base (Figure D)
The soldering iron holder 13 could be installed on either
right or left side on base 14 with screwdriver (not in-
cluded) as an option for left or right-handed user.

14 GB
Use
Using the product
Turn the retaining screws 19 on the alligator clips 18 in a
clockwise direction. Clamp the item to be repaired with
the alligator clips 18 in the repair device 15 .
Move the On/Off switch 9into position “ON” to
switch on the LEDs 20 .
Note: The LED bulbs 20 are non-replaceable.
Point the precision engineer’s LED magnifying glass 1
with the LED lamps 20 at the clamped work piece.
Release the alligator clips 18 in order to remove the
work piece.
Move the On/Off switch 9into position “OFF” to
switch off the LEDs 20 .
Changing the batteries
Pull the battery compartment cover 3in the direction of
the arrow to remove it from the battery compartment 4.
Use the ribbon to remove the old batteries.
Place the new batteries 21 of type 1.5V , AAA into
the battery compartment 4.
Note: Ensure the correct polarity. This is shown in the
battery compartment 4.
Push the battery compartment cover 3back in the
opposite direction to the arrow back in order to close the
battery compartment 4.

15GB
Troubleshooting
= Problem
= Cause
= Solution
The LED lamps 20 do not light up.
The batteries 21 are flat.
Replace the used batteries 21 with new ones
(see: “Changing the batteries”).
The batteries 21 have been inserted incorrectly.
Check the correct polarity of the batteries 21
(see: “Inserting the batteries”).
Cleaning and maintenance
CAUTION! Clean the precision engineer’s LED magnify-
ing glass 1very carefully in order to avoid scratches.
Do not use corrosive or abrasive cleaners under any
circumstances.
Use a cleaning cloth for cleaning the product. Moisten it
a little if necessary.
Use a dry, fluff-free cloth for cleaning the lens.
Never immerse the product in water or other liquids under
any circumstances.
If you are not using the product, store it in such a way
that the precision engineer’s LED magnifying glass 1is
not scratched. Wrap the product in a soft cloth.

16 GB
QDisposal
The packaging is made entirely of recyclable
materials, which you may dispose of at local
recycling facilities. The Green Dot is not valid for
Germany.
b
a
Observe the marking of the packaging materials
for waste separation, which are marked with
abbreviations (a) and numbers (b) with following
meaning: 1–7: plastics/20–22: paper and
fibreboard/ 80–98: composite materials.
The product and packaging materials are recycla-
ble, dispose of it separately for better waste treat-
ment. The Triman logo is valid in France only.
Contact your local refuse disposal authority for
more details of how to dispose of your worn-out
product.
To help protect the environment, please dispose of
the product properly when it has reached the end
of its useful life and not in the household waste.
Information on collection points and their opening
hours can be obtained from your local authority.
Faulty or used batteries/ rechargeable batteries must be
recycled in accordance with Directive 2006/66/EC and its

17GB
amendments. Please return the batteries/rechargeable bat-
teries and/or the product to the available collection points.
Environmental damage through
incorrect disposal of the batteries/
rechargeable batteries!
Batteries/rechargeable batteries may not be disposed of
with the usual domestic waste. They may contain toxic heavy
metals and are subject to hazardous waste treatment rules
and regulations. The chemical symbols for heavy metals are
as follows: Cd = cadmium, Hg = mercury, Pb = lead. That is
why you should dispose of used batteries/rechargeable
batteries at a local collection point.

18 HU
Bevezető..............................................................Oldal 19
Rendeltetésszerű használat....................................Oldal 19
A részek megnevezése...........................................Oldal 20
Műszaki adatok ......................................................Oldal 21
Csomagolás tartalma..............................................Oldal 21
Biztonság.............................................................Oldal 22
Általános biztonsági tudnivalók.............................Oldal 22
Az elemekre/akkukra vonatkozó
biztonsági tudnivalók..............................................Oldal 23
Az üzembevétel előtt................................Oldal 25
Az elemek behelyezése..........................................Oldal 25
A javító szerkezet felszerelése ...............................Oldal 26
A nagyító felszerelése ............................................Oldal 26
Állvény elhelyezése ................................................Oldal 27
Használat............................................................Oldal 27
A termék használata...............................................Oldal 27
Az elemek cseréje...................................................Oldal 27
Hibák elhárítása...........................................Oldal 28
Tisztítás és ápolás........................................Oldal 28
Mentesítés ..........................................................Oldal 29

19HU
Finommechanikai műszerész
készlet LED nagyítóval
Bevezető
Gratulálunk új termékének vásárlása alkalmából.
Ezzel a döntésével vállalatunk értékes terméke
mellett döntött. A használati utasítás ezen termék
része. A biztonságra, a használatára és a megsemmisítésre
vonatkozó fontos tudnivalókat tartalmazza. A termék haszná-
lata előtt ismerje meg az összes használati és biztonsági
tudnivalót. A terméket csak a leírtak szerint és a megadott
felhasználási területeken alkalmazza. A termék harmadik
személy számára való továbbadása esetén kézbesítse vele
annak a teljes dokumentációját is.
Q
Rendeltetésszerű használat
A termék a tárgyak 2,5/5-szeres nagyítására szolgál. A be-
épített LED-ek a jobb kontrasztot és a nagyobbítandó tárgy ár-
nyékmentes megjelenítését szolgálják. A termék kiegészítőleg
2 rögzítő kapoccsal és egy forrasztópáka tartóval is rendelkezik.
A termék bármilyen más alkalmazása vagy megváltoztatása
nem rendeltetésszerűnek minősül, és sérülésveszélyt illetve ká-
rosodást okozhat. A nem rendeltetésszerű használatból eredő
károkért a gyártó nem vállal jótállást. A termék kizárólag bel-
téri üzemeltetésre alkalmas. A termék nem keresekedelmi, vagy
más célú alkalmazásra készült.

20 HU
Ez a termék nem alkalmas háztartások központi
fényforrásaként.
Q
A részek megnevezése
1finommechanikai-LEDes nagyító
2lencse (nagyítása 2,5-/5-szörös)
3elemrekesz fedél
4elemrekesz
5gömbcsukló
6rögzítő csavar (nagyító gömbcsuklója)
7nagyító rögzítő kapcsa
8rögzítő csavar (nagyító magasság-beállítás)
9be-/kikapcsoló
10 tartórúd (magasság-beállítás)
11 rögzítő kapocs (javító szerkezet)
12 rögzítő csavar (javító szerkezet magasságbeállítás)
13 forrasztópáka tartó
14 láb
15 javító szerkezet
16 rögzítő csavar (javító szerkezet gömbcsuklója)
17 rögzítő csavar (javító szerkezet)
18 krokodil kapcsok
19 rögzítő csavarok (krokodil kapcsok)
20 LED-es lámpák (B ábra)
21 elemek (C ábra)
22 tartórúd (a krokodilcsipesz tartásához)