Pr lighting Aqua 580 User manual

AQUA 580 BEAM

PR-2569

The user manual contains important information about the safe installation and use of a projector. Please read

andfollowthese instructions carefullyandkeepthemanual in asafeplaceforfuturereference.

PR LIGHTING LTD.

http://www.pr-lighting.com

INDEX

SAFETYANDWARNINGS…………………………………………………………………………………

INSTRUCTIONS……………………………………………………………………………………………

●CLEANINGANDMAINTENANCE………………………………………………………………………

●LUBRICATION……………………………………………………………………………………………

●TROUBLESHOOTING……………………………………………………………………………………

APPEARANCE………………………………………………………………………………………………

INSTALLATION ……………………………………………………………………………………………

●RIGGING …………………………………………………………………………………………………

●POWERCONNECTIONS ………………………………………………………………………………

●DMXCONTROLCONNECTIONS ………………………………………………………………………

●DMXTERMINATOR………………………………………………………………………………………

●ALIGNMENT/INSTALLATION/REPLACEMENTOFALAMP …………………………………………

●GOBOREPLACEMENT …………………………………………………………………………………

SETUPANDCONFIGURATION……………………………………………………………………………

●FRONTPANELOPERATION ……………………………………………………………………………

●DMXSTARTADDRESS …………………………………………………………………………………

●DMXWIRELESSCONTROL………………………………………………………………………………

●STAND-ALONEMODE …………………………………………………………………………………

●MASTER/SLAVEMODE…………………………………………………………………………………

OPERATION MENU…………………………………………………………………………………………

DMXPROTOCOL……………………………………………………………………………………………

SIGNSONTHETOUCHSCREEN…………………………………………………………………………

ERRORMESSAGES………………………………………………………………………………………

10.

TECHNICALDATA…………………………………………………………………………………………

11.

CIRCUITDIAGRAMANDPCB CONNECTIONS…………………………………………………………

●CIRCUITDIAGRAM………………………………………………………………………………………

●PCBCONNECTIONS………………………………………………………………………………………

12.

COMPONENTORDERCODES……………………………………………………………………………

ACCESSORIES

Thefollowing itemsaresuppliedwith theprojectorand pleasecheck:

Name

Quantity

Unit

Remark

Gclamps

Pcs

XLR connector

Set

Maleand female

Safetycord

User manual

Ω clamps

Pcs

Optional

Please note that as part of our ongoing commitment to continuous product development, specifications are

subject to change without notice. Whilst every care is taken in the preparation of the manual we reserve the

right to change specifications in the course of product improvement. The publishers cannot be held responsible

for the accuracy of the information herein, or any consequence arising from them.

Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and /

or the unit are in good condition before installation and use. Should there be any damage caused by

transportation, consult your dealer and do not use the unit. Any damage caused by improper use will not be

assumed by the manufacturer and / or dealer.

Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one yearstarting from

thedeliverydatebutthelight sourceisnot withinthewarranty.

1. SAFETYANDWARNINGS

NOTE

Before a projector’s installation, power-on, operation and maintenance, please carefully read

the safety information hereinafter!

Thefollowingsafety signsareusedinthe usermanual.

Warning

User

Manual

Electrical

shock

Goggles

Protective

Gloves

Flames

High

Temperature

● When unpacking , check if there is transportation damage before using the projector. Should there be any

damagecausedbytransportation,consultyourdealeranddonotuseit.

●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector

ashe/shelikes.

●Pleasebenotedthatthedamagecausedbychangingtheprojectoratwillisnot warranted.

●Do not hesitate to contact the dealer or the manufacturerifanyquestionsor advice.

● Theprojectoris forindoorand outdooruse,IP66.

● Itcanbeusedinhumidand dustyareas.And itcancontactwaterandothernon-corrosiveliquids.

●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while

beingoperated

●The projector is only intended for installation, operation and maintenance by qualified personnel. And the

operationmuststrictlyfollowthe procedures inthemanual

●No repairablepartsintheprojectoranddonotopencoversfor maintenancebyyourself.

●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned..

●Do notconnectthisdeviceto anytypeofdimmerpack.

●Afterlampswitchedon,theminimumdistancebetweentheprojectorandilluminatedsurfaceis 18m.

●lensandotheropticalpartsshallbereplacedimmediatelyiftheyhavedeformedorbeendamaged,otherwise the

lightoutputwillbe compromised.

●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a

projector whilecovers(housing)areoff.

●Keep thelamp cleanand do not touchit withbare hands.

●While operatingit, wearprotectiveitems.

●Anyelectricalconnectionmustbecarriedoutbyaqualifiedperson.

●Before installation,pleaseconfirmthe voltagesuppliedmatcheswhatisrequired fortheprojector.

●Eachprojectormustbeproperlyearthedand installedasper relatedelectrical standards.

●Do notusepower cord withitsinsulatordamagedandconnectthepower cord withothercables.

●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully

orbypullingthepower cable.

●Allpowercordsmustconform torelatedsafetyandregulations.

●Whilebeingoperated,theprojectorshouldnotbeunderrainsorinhumidity.

●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other

electricalparts’ lifewillbeshortened .

●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety

cord suppliedthroughthesafetycordholesfor safetysupport.

●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from

powermains.

●Afterrunningfor30minutes, thetemperatureofthehousingoftheprojectoris45℃.Afterstableoperation,

itstemperatureis75℃.

●While thelampisstrickenforthefirsttime,therewillbesmokeandstrangesmell.It’s normal and does not

mean theprojectorhassome defects.

●Do notmount theprojectordirectlyoninflammablesurface.

●Do notprojectthebeamstraightlyoncombustibleitemsand theminimumdistancebetweentheprojector

andilluminateditemsis18m.

●Aprojector should be installed with good ventilation and the minimum distance between the projector and

wallsis50cm.At thesametime,pleaseensurethefansandairinletsand outletsare workable.

2. INSTRUCTIONS

●CLEANINGANDMAINTENANCE

If a projector can’t start. Please check if the fuse is blown up. If it does, replace it with a new fuse with same ratings. And the

projector has over-temperature protective device. Ifthe temperature is too high, the protective device will be triggered to shut the

projector off. When it happens, please check if the fans run normally or fan shield is blocked by dust. After the issue is solved,

restarttheprojector.

The accumulation of oil, smoke and dust on the lens will compromise the light output. Cleaning a projector is verynecessary to

ensure a reliable use of it. Cooling fans need to be cleaned every 15days. Internal lens, reflectorand hotmirror need to be cleaned

periodicallyto optimize lightoutput.

Cleaning frequency is to bedecided byoperations and its environment. Use soft clothand normal detergent for glass for cleaning

work. It’s advised external optical system be cleaned every 20days and internal optical systems every 30/60days. Keep lens clean

anddo not touch optical parts with bare hands.

Special note:

It’s normal phenomena that there will be mild water mist on the lens while the waterproof product is in use.

●Beforeanymaintenance andcleaning,pleaseensuretheprojectisoff thepower.

●Onlyqualifiedpersonisallowed todo maintenance.

●During maintenanceandbeforemaintenance, the projectormustbe offpower.

●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens

whether itrunsornot.

●Do notusealcoholor otherorganicsolvent to cleanthehousingtoavoiddamage.

●Do notuseany solventwithchemical elementsto cleancolor filtersor hot mirror.

●LUBRICATION

To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and

focuslensbelubricatedevery2months.Highquality andhightemperaturelubricant/greaseisadvised..

●TROUBLESHOOTING

PROBLEM

ACTION

The projector doesn’t switch on

Checkthe fuseonthe power socket.

Checkthelamp.

Thelampisonbut the projector doesn’t respond

to thecontroller

Makesurethatthe fixture’s start address is right

Replace orrepair theXLRsignal cable.

Theprojector functions intermittently

Makesurethefanisworkingwellorfansandtheirshieldsarenotblocked

Beam appearsdim, Lowinbrightness

Make surethelamp is within itslifespan

Remove dustorgreasefrom thelenses.

Theprojectimageappears to have ahalo

Carefullycleanthelamp,opticallensesandothercomponents.

HeavilyDefectiveBeam

Checkif lensareingoodcondition(notcracked)

Cleandustorgrease on thelens.

3. APPEARANCE

1. FrontLens

2.Tilt Lock

3. PanLock

4. Base

5. FrontLensCover

6. UpperHeadCover

7. ChamberCover

8. LowerHeadCover

9. FanCover

10. PanLatch

11.TiltHandle

RearPaneloftheBase

1.Waterproofpowersocket

2.Waterprooffuseholder

3.Waterproof5-pinXLRSocket(Male)

4.Waterproof5-pinXLRSocket(Female)

5.WaterproofEthernetPort

6.WaterproofDMX Wireless Receiver(Only

forprojectorrequestedforwirelesscontrol)

7. Gore-Tex membrane

FrontPaneloftheBase

1. Return Key

2. UPKey

3. DownKey

4. Enter Key

4. INSTALLATION

●RIGGING

Before moving a projector, Please lock Pan and Tilt. Before its operation, please unlock them. It’s forbidden to run a

projectorwithpowerwhileit islocked.

Take 2 clamps and the safetycord out fromthe package and mount 2 clamps on the underside of fixture with 2 retainers attached

to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the

underside of the base as shown above) To pass the SAFETYCORD through the HOLES for safety! Always ensure that the

projector is firmlyanchoredto avoid vibrationand slippingwhilst functioning. Always ensurethatthe structurethatyouare going

to mountthe projectortois secureandstrong enoughtosupporttheweightofaXR1000 Framing.

WARNING:

●The projectorMUSTbe liftedorcarried by theHANDLESinsteadofclamps.

●.For safety the safety cord should afford 10 times the Projector’s weight.

●POWERCONNECTION

Connectthe powercordasfollows:

L(live)=brown

E(earth)=yellow/green

N(neutral)=blue

Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each

projectorbeconnected with powerseparatelyso thattheymaybeindividuallyswitchedonand off.

●The earth wire(yellow/green) must be connected to the ground. And electrical connection must be in

accordancewiththe standardsconcerned.

●Ifany questionsabouttheelectricalinstallation,do notcontinuebutconsulta qualifiedelectrician.

Control Panel

Handle

Clamp

Safety Cord Warning

Please run the safety cord

through the two safety cord

holes to ensure safety safety

cord holes

●DMXCONTROLCONNECTION:

Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with

each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the

projector)or5pinXLRplugs and sockets.The XLR'sareconnected asshowninthefigureabove.

Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets

mustn’t be connected in anywayotherthan mentioned in the abovefigure.TheXR330BWSacceptsdigitalcontrol signalsinprotocol

DMX512(1990).

Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second

fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX

terminatorasshowninthefigurebelow.

●DMXTERMINATOR

In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents

electricalnoise fromdisturbingandcorruptingtheDMXcontrolsignals.

The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged

intotheoutputsocketonthelastprojectorinthechain.Theconnectionsare illustratedbelow.

DMX Teminator

DMX

Controller

Input Output Input Output Input

120

DMX TERMINATOR

CONNECTION

Connect a 120 (OHM) resistor

across pins 2 and 3 in an XLR plug

and insert into the DMX out socket

on the last unit in the chain. PIN 3

PIN 2

● ALIGNMENT/INSTALLATION/REPLACEMENTOFALAMP

Please hold the projector well before adjustment/installation/replacement oflamp. As shown in figure1, remove fan cover ofthe head

andheatsink.

Removal/Installationoflampasshowninfigure2

Adjustthelampasshowninfigure3

Beforetheremoval of thelamp, unplugthelamp wires.And pluglamp wiresaftera newone is in.

●Don’t touch the internal surface of the reflector and the burner of the lamp with bare hands so as not to impair the

beam output. There is aprotruding metal wire inthe lamp, while installation do not damage it. Hold the lamp body

well before its removal. It’s forbidden to use forceontheceramicstand,otherwiseitwill loosenorfall off.

●Pleaseread "Instructions" enclosedwiththe lamp

●While adjusting thelamp, it is forbidden to carryout the functions not associated with lamp adjustment.

Figure1:loosen4 screwsofthefancoveroftheheadbefore removingit.Thenloosenthescrewsofheatsinkandremove it

andthefan.

Figure2:Unplugthelampwires, pushthe upperclipping platetowardthe springwithforce,butpushthelamp inthe

opposite directiontill itisofftheplate,thentakethelamp outobliquely.Thesame appliestoitsinstallation.

Figure3:Afterthereplacementofthelamp,pleaseensurefirstthelampisclippedwellbeforeplugginglampwires.Turnthe

lamp on and adjust the lamp’s positiontothemiddle.Afterthat, installtheheatsink,fanandfancover.

1. After theprojectoris powered on, disablethe following functioninthe menu:services-factorymode-lamp fansensor, thenshut

itfrompower

2. Loosenthe4screwsofthefancover and removeit.

3. Loosen4 screwsofthe fanplate,remove the fanand the clumpweight,loosen10screwsofthe heat sink and removeit.

4. Pushthe upperclippingplateofthe lamptowardsthespring,and atthesametimepusthelamptowardsthe opposite tillitisoff

theplateandremoveitobliquely,

5. Theinstallationofthelampisthesame as itsremoval

6. Checkifthe lampwiresarepluggedwell,thenturnonthelampfor adjustment

7. After theadjustmentofthe lamp,activatethe followingfunctioninthemenu:services-factorymode-lamp fansensor.Thenshut

itfromthepower

8. Check if the sealsare goodor not. Ifnot, replace themwith good ones. Ifno, installthe heatsink, fan and fancoverinthe

oppositesequencesastheremoval.

9. After installation,powerit on.Theprojectorwillexecute the totalreset.After that, the projectorcanbe used normally.

●GOBOREPLACEMENT

Rotating gobo wheel

Rotator

Gobo

Gobo spring

Rotator

Replacement of the Gobos:

Open the chamber cover after loosening 4 screws.

Select the rotator for replacement of gobo. Push

the rotator at the opposite side of its gear till it is

off the holder of the rotating gobo wheel. Remove

the rotator gently . After replacement of the gobo,

place the rotator into the wheel and ensure it is in

the right position and not loose.

示例2：拔下灯泡线,然后

将上压片向拉簧方向用力

推，灯泡往相反的方向推，

待灯泡脱离上压片时倾斜

取出，装灯泡同理.

示例1：松开后盖4颗螺丝，

取下后盖，再松开散热器

螺丝，取下散热器和尾部

风机

示例3：换泡完毕，先确定灯

泡是否卡稳，再插上灯泡线，

亮泡，调整灯泡居中，完毕

锁上散热器，风机以及后盖.

灯泡上压片

灯泡压片

DANGER!

Beforereplacementofgobos,the projectormust beoff the power.

5. SETUPANDCONFIGURATION

●FRONTPANELOPERATION

To browse through or change the projector ’s settings, press ENTER key for more than 3s(press ENTER key after power on) to

unlock the screen , then press UP/DOWN key to enter the projector ’s function menus. Each main menu has its sub-menus. And

eachmenustandsforspecial function. Forthe details,please seethefollowing6th point ”Operation Menu”.:

1. At the page to set the fixture’s functions, press UP or DOWN keyto selectthe functions desired.

2. While menu operations, the FUNC keyto escape, and ENTER key is used to confirm. Press ENTER key to save the changes

orenterintothe sub menus.Press UP or DOWN keyto changethenumbers(minusorplus).

Press FUNC keyto go to the upplermenu. If no keyispushed, the systemwillgo back to initial status automatically.

●DMX STARTADDRESS

Each projector mustbegiven aDMX start address so that the correctprojectorresponds to the correct controlsignals. This DMX start

address is the channel number from which the projector starts to “listen” to the digital control information being sent out from the

controller. The projector has 3DMX modes. There are standard mode ,short mode and extended mode. For example standard mode

has 26 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 027, No. 3 projector’s address 053,No. 4

projector’s address 079, andso on.

Switch on the Projector . Press ENTER key more than 3 seconds to unlock panel, then press UP or DOWN key to enter into the

fixture’s operation menus.

Select DMXAddressiconand pressENTERkeyonthedisplayand select DMXaddressatthe2nd levelmenu fortheaddresssetting.

Press UP or DOWN keyfor theDMXaddress desired.

Press ENTER keytoconfirm.

Press the FUNC keytogo back tothe upperlevelmenu.

●DMXWIRELESSCONTROL

Theprojector haswirelesscontrolfunctionwith wirelessreceivermoduleandantenna forremote control.

Thesetupofitisbelow:

1. Press ENTER for more than 3s to unlock the control panel, then press UP or DOWN key to enter into the operation

menu and select “Config Settings”.

2. Select “Wireless Only” from the menu of “Signal Select”.

Only after the projector is linked with a transmitter, can it receive wireless signal sent by the transmitter. If unlinking it,

Press “Enter” for the menu of Un-link Wireless under the upper level menu of Config Settigns ,then the fixtureis unlinked

with thewirelesstransmitter.

●STAND-ALONEMODE

Operate the projector without connecting with a controller, enable the master mode through the operation panel, the

projector will run in Stand-Alone mode automatically.

DMX address can be set at any number within 512.

●MASTER/SLAVEMODE

Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,

connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR controlcable and then connect the second

fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the

last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.

StartAddresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can

besetaccordingly.

AfterPoweredon,the group will runinMaster/Slave Mode

6.OPERATIONMENU

1st

LEVEL

2ndLEVEL

3rdLEVEL

4thLEVEL

5thLEVEL

Address

DMXAddress

1-512

Reset

Total Reset

ReallyReset?

ConfirmorCancel

Pan&TiltReset

ReallyReset?

ConfirmorCancel

ColourSystemReset

ReallyReset?

ConfirmorCancel

GoboReset

ReallyReset?

ConfirmorCancel

Dimmer/Shutterreset

ReallyReset?

ConfirmorCancel

Fo.Fr.Pr.Reset

ReallyReset?

ConfirmorCancel

DMXChannel Mode

Short Mode

Input Output

Master Slave Slave

Input Output Input

DMX

Controller

DMX Teminator

Config

Settings

StandardMode

ExtendedMode

ViewSelectedMode

Lamp Control

OFF/ ON

On ByPower On

OFF/ ON

ControlByDMX

OFF/ ON

Lamp ECOPower

OFF/ ON

SignalSelect

XLROnly

XLRFirst

WirelessOnly

WirelessFirst

WirelessIn/XLR Out

LossofDMX

Normaltimeout

Hold LastValue

DisplayConfig

DisplayMode

OffAfterDelay

OnAlways

DisplayInvert

InvertOFF

InvertON

InvertAuto

LanguageSetting

English\Chinese

Touch Calibration

TemperatureUnit

CelsiusDegree

FahrenheitDegree

Un-LinkWireless

Really Un-Link?

ConfirmorCancel

Factory Defaults

RestoreDefaults?

ConfirmorCancel

Option

Pan/TiltSettings

PanDMXInvert

OFF/ ON

Settings

TiltDMXInvert

OFF/ ON

PanTiltSwap

OFF/ ON

XYFeedback

OFF/ ON

Pan/Tilt mode

Speed/Time

Note: "Speed Mode"means

PanandTilt willmovefrom

PointAtoPointBattheir

respectivemaximum

speeds."TimeMode" means

bothPanandTilt willarriveat

designatedpointat thesame

time. It'sadvised TimeModebe

used iftheprojector runscircles

orinobliquelines.

InvertSettings

DimmerInvert

OFF/ ON

CYMInvert

OFF/ ON

Information

ViewDMXValues

Channel Value

Strobe XXX

Dimmer XXX

CYMMacro XXX

Cyan XXX

Yellow XXX

Magenta XXX

CTO XXX

ColorWheel XXX

Fixed GoboWheelXXX

Rot. GoboWheel1XXX

Rot. Gobo1RotationXXX

Prism1 XXX

Prism1Rotation XXX

Prism2 XXX

Prism2Rotation XXX

Focus XXX

Pan XXX

Tilt XXX

ControlFunction XXX

Lamp Hours

XXXH

Reset Lamp Hours

Total Hours

××××H

Temperature

DisplayBoard=×××C

Pan&Tiltboard=×××C

DriverBoard1=×××C

DriverBoard2=×××C

HeadSensor=×××C

SoftwareVersion

PCB Sys Boot

DisplayBoard xxx xxx

Pan&Tiltboard xxx xxx

Tiltboard xxx xxx

DriverBoard1 xxx xxx

DriverBoard2 xxx xxx

ElectronicSN

XXXXXX

RDMDeviceLabel

XR550 Beam

ANSIE1.20RDM

FanStatus

Fan Speed Status

Lamp Fan1 xxx on/off

Lamp Fan2 xxx on/off

HeadFanxxx on/off

Gobo Fan xxx on/off

Lamp TFan xxx on/off

Lamp RFan xxxon/off

AccelerationSensor

X Axis:XXX

YAxis:XXX

ZAxis:XXX

Service

ManualEffectControl

StrobeXXX

DimmerXXX

DimmerFine XXX

CYMMacroXXX

Cyan XXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

MagentaFineXXX

CTOXXX

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel1XXX

Rot. Gobo1Rotation XXX

Rot. Gobo1RotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TileXXX

TiltFineXXX

Pan&Tilt Speed &Time

XXX

ControlFunctionXXX

FactoryMode

XXX

…

Operation

Mode

DMXMode

ChangeOperationMode?

ConfirmorCancel

MasterMode

PresetMemory

ChangeOperationMode?

ConfirmorCancel

UserMemory1

ChangeOperationMode?

ConfirmorCancel

UserMemory2

ChangeOperationMode?

ConfirmorCancel

Stand-AloneMode

PresetMemory

ChangeOperationMode?

ConfirmorCancel

UserMemory1

ChangeOperationMode?

ConfirmorCancel

UserMemory2

ChangeOperationMode?

ConfirmorCancel

StaticScene

ChangeOperationMode?

ConfirmorCancel

User

Memories

Edit UserMemory

Edit UserMemory1

Edit UserMemory2

（1~200Scenes）

SceneXX

（1~200Scenes）

StrobeXXX

DimmerXXX

DimmerFine XXX

CYMMacroXXX

CyanXXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

MagentaFineXXX

CTO XXX

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel1XXX

Rot.Gobo1Rotation XXX

Rot. Gobo1RotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TileXXX

TiltFineXXX

Pan&TiltSpeed &TimeXXX

ControlFun.

XXX

DelayTime XXX

Delaytimeunit ms/s/m

LinktoStep XXX

Edit Static Scene

StrobeXXX

DimmerXXX

DimmerFine XXX

CYMMacroXXX

Cyan XXX

Cyan FineXXX

YellowXXX

YellowFine XXX

MagentaXXX

MagentaFineXXX

CTO XXX

ColorWheelXXX

ColorWheelFineXXX

Fixed GoboWheel XXX

Rot. GoboWheel1XXX

Rot. Gobo1Rotation XXX

Rot. Gobo1RotationF.XXX

Prism1XXX

Prism1RotationXXX

Prism2XXX

Prism2RotationXXX

FocusXXX

FocusFineXXX

PanXXX

PanFineXXX

TileXXX

TiltFineXXX

Pan&Tilt Speed &Time

XXX

ControlFunction

XXX

InitUserMemory

Reset UserMemory1

Reset UserMemory?

ConfirmorCancel

Reset UserMemory2

Reset UserMemory?

ConfirmorCancel

Reset Static Scene

Reset Static Scene?

ConfirmorCancel

Remarks:Lampfansensorisonlyused duringlamp adjustment

Open: the lamp is affected by the lamp fan. If the lamp fan fails, the lamp won’t be on.

Close: the lamp is not affected bythe lamp fan. Even if the lamp fan is not installed, the lamp will be on, but

PanandTiltarewithoutforce.

“Close” status is used only in emergency. If the lamp fan won’t run for long, it will cause harm to the

lamp.

After lamp adjustment, set the “lamp fan sensor as “Open” and activate total reset.

7.DMXPROTOCOL

Short

mode

Standard

mode

Extended

Mode

FUNCTION

DMX

DESCRIPTION

Strobe

000-010

011-025

Open

026-225

Strobe speed fromslowtofast

226-246

Randomstrobefromslowtofast

247-255

Open

Dimmer

000-035

036-255

Linear dimming（0-100%）

DimmerFine

000-255

Dimmerin16 bit

CYMMacro

000-016

White

017-035

Yellow+ Magenta=Red

036-054

Yellow

055-073

Yellow+Cyan=Green

074-092

Cyan

093-111

Cyan+Magenta=purple

112-128

Magenta

129-255

CYMcolormixingfromslowtofast

Cyan

000-255

Cyan(linear 0~100%)

CyanFine

000-255

Cyan in16 Bit

Yellow

000-255

Yellow(linear0~100%)

YellowFine

000-255

Yellowin16Bit

Magenta

000-255

Magenta (linear0~100%)

Magenta Fine

000-255

Magenta in16Bit

CTO

000-005

006-024

Diffuser

025-255

Linear CTO

CTO Fine

000-255

CTO in 16bit

ColorWheel

000-063

Indexing(0-360degrees)

064-068

Color1(Red)

069-073

Color2(LightGreen)

074-078

Color3(Blue)

079-083

Color4(Cyan)

084-088

Color5(Yellow)

089-093

Color6(Magenta)

094-098

Color7(Orange)

099-103

Color8(Green)

104-108

Color9(DarkBlue)

109-113

Color10(UV)

114-118

Color11(LightYellow)

119-123

Color12(DarkYellow)

124-127

White

128-191

Rotation,Clockwisefromslowtofast

192-255

Rotation,Anti-clockwisefromfasttoslow

ColorWheelFine

0000-255

ColorWheelin16Bit

Fixed Gobo

Wheel

000-019

White

020-025

Gobo1

026-031

Gobo2

032-037

Gobo3

038-043

Gobo4

044-049

Gobo5

050-055

Gobo6

056-061

Gobo7

062-067

Gobo8

068-073

Gobo9

074-079

Gobo10

080-085

Gobo11

086-091

Gobo12

092-097

Gobo13

098-103

Gobo14

104-109

Gobo15

110-115

Gobo16

116-121

Gobo17

122-127

Gobo18

128-155

Clockwiserotation fromslowtofast

156-183

AntiClockwiserotationfromslowto fast

184-187

Shakeeffect 1fromslow tofast

188-191

Shakeeffect 2fromslowto fast

192-195

Shakeeffect 3fromslow tofast

196-199

Shakeeffect 4fromslowto fast

200-203

Shakeeffect 5fromslow tofast

204-207

Shakeeffect 6fromslowto fast

208-211

Shakeeffect 7fromslow tofast

212-215

Shakeeffect 8fromslowto fast

216-219

Shakeeffect 9fromslowto fast

220-223

Shakeeffect 10fromslow tofast

224-227

Shakeeffect 11fromslowtofast

228-231

Shakeeffect 12fromslow tofast

232-235

Shakeeffect 3fromslowto fast

236-239

Shakeeffect14fromslow tofast

240-243

Shakeeffect 15fromslowto fast

244-247

Shakeeffect 16fromslow tofast

248-251

Shakeeffect 17fromslowto fast

252-255

Shakeeffect 18fromslowto fast

RotatingGobo

Wheell

000-015

White

016-031

Gobo1

032-047

Gobo2

048-063

Gobo3

064-079

Gobo4

080-095

Gobo5

096-111

Gobo6

112-127

Gobo7

128-156

Rotation （clockwiseFromslowtoFast）

157-185

ReverseRotation（anti-clockwise From slow to

Fast）

186-195

ShakeofGobo1fromslowtofast

196-205

ShakeofGobo2fromslowtofast

206-215

ShakeofGobo3fromslowtofast

216-225

ShakeofGobo4fromslowtofast

226-235

ShakeofGobo5fromslowtofast

236-245

ShakeofGobo6fromslowtofast

246-255

ShakeofGobo7fromslowtofast

Gobo Rotation

000-128

GoboIndexing(0~540degrees)

129-188

Rotation （Clockwise FromslowtoFast）

189-195

Stop

196-255

Rotation （Anti-ClockwiseFromslowtoFast）

Gobo Rotation

Fine

000-255

GoboRotation in16Bit

Prism1

000-016

Open

017-127

Prism1

128-255

Prism2

Prism1 Rotation

000-128

PrismIndexing

129-191

Rotation(Clockwisefromslowtofast)

192

Stop

193-255

Rotation(Anti-Clockwisefromslowtofast)

Prism2

000-016

White

017-127

Prism3

128-255

Frostin

Prism2 Rotation

000-128

Prism2 Indexing

129-191

Rotation(Clockwisefromslowtofast)

192

Stop

193-255

Rotation(Anti-Clockwisefromslowtofast)

Focus

000-255

Linear focus

FocusFine

000-255

Focusin16bitprecision

Pan

000-255

Pan(0°~540°)

PanFine

000-255

Panin16bit

Tilt

000-255

Tilt(0°~270°)

Tilt Fine

000-255

Tilt in16bit

Pan &TiltSpeeds

000-255

Pan&Tilt SpeedfromFast to Slow

Control

000-019

Reserved

Keep in the DMX range for more than 5S to activate the following

functions.Ifpower-off,the followingareinvalid.

020-024

Graphic DisplayOn

025-029

Graphic DisplayOff

030-034

Reserved

035-039

Lamp ECOPower

040-044

Lamp FullPower

045-089

Reserved

090-094

Pan&Tilt Speed Mode

095-099

Pan&TiltTimeMode

100-129

Reserved

130-139

Lamp On

140-149

Pan&Tilt Reset

150-159

ColorSystemReset

160-169

Gobo Wheel Reset

170-179

Dimmer/ShutterReset

180-189

Zoom/Frost/Focus/PrismReset

190-199

Reserved

200-209

Total Reset

210-229

Reserved

230-239

Lamp Off

240-255

Reserved

1. The projector can’t be turned on within 1 minute after the lamp-off.

2.Fanerrorcancauselamp-off.

8.SIGNSONTHETOUCHSCREEN

Lamp comtrol

OptionSettings

Chinese-English

Information

Error messages

Service

Address

OperationMode

Reset

UserMemories

ConfigSettings

9.ERRORMESSAGES

Thesystemcandetectsomeerrorsduringthereset,if displayed,touch to viewtheerror.

The errormessagesare as follows:

Name

Type

Correction

Pan

Timeout/magnetSensor/Encoder