PR Lighting XR330 Framing User manual

XR330 Framing
PR-2357
This product manual contains important information about the safe installation and use of this projector.
Please read and follow these instructions carefully and keep this manual in a safe place for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/24
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS
STAND-ALONE MODE
MASTER/SLAVE MODE
6
7
7
OPERATION MENU 8
ERROR MESSAGES 13
REPLACING GOBOS 14
DMX PROTOCOL 15
LED INDICATION 18
MAINTENANCE 18
LUBRICATION 18
KEEPING THE PROJECTOR CLEAN 18
TROUBLESHOOTING 18
TECHNICAL DATA 19
ELECTRICAL DIAGRAM 22
COMPONENT ORDER CODES 23
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to
change without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change
specifications in the course of product improvement. The publishers cannot be held responsible for the accuracy of the
information herein, or any consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the
unit are in good condition before installation and use. Should there be any damage caused by transportation, consult
your dealer and do not use the unit. Any damage caused by improper use will not be assumed by the manufacturer and
/ or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
G clamps 2 Pcs
XLR Signal Cable 1 Set with plug and socket
Safety cord 1 Pc
User’s manual 1 Pc
Ωclamps 2 Pcs Optional

When unpa
c
b
e any dam
a
The project
o
humidity an
d
The project
o
The project
o
The project
o
ventilation s
l
Do not proj
e
Avoid direct
Do not atte
m
Electrical co
n
Before insta
l
It is essentia
l
Do not conn
e
Make sure t
h
Only handle
Keep the la
m
The project
o
shown in “i
n
Shields and
example by
c
Exterior sur
f
There is no
removed.
If you have
a
Always d
i
work !
c
king and befo
r
a
ge caused by t
r
o
r is for indoor
d
dust. Do not
a
o
r is not design
e
o
r is only inten
d
o
r must be inst
a
l
ots are blocke
d
e
ct the beam on
t
exposure to th
e
m
pt to dismantl
e
n
nection must
o
l
lation, ensure t
h
l
that each proj
e
e
ct this device
t
h
at the powe
r
-
c
the powe
r
-cor
d
m
p clean. Do n
o
o
r should alwa
y
n
stalling the pro
j
lens shall be
c
c
racks or deep
s
f
ace temperatur
e
user servicea
b
a
ny questions o
r
i
sconnectio
n
SA
F
r
e disposing of
r
ansportation, c
o
use only, IP20
.
a
llow contact w
i
e
d or intended t
o
d
ed for installa
t
i
o
a
lled in a loca
t
d
.
t
o infla
m
mable
e
light from the
e
and/or modif
y
o
nly be carried
o
h
at the voltage
a
e
ctor is correctl
y
t
o any other ty
p
c
ord is never cr
i
d
by the plug.
N
o
t touch the la
m
y
s be installed
w
j
ector” section.
c
hanged if the
y
s
cratches.
e
s of the lumin
a
b
le parts inside
r
suggestions,
d
n
from Po
w
F
E USAG
E
the carton che
c
o
nsult your de
a
.
Use only in d
r
i
th water or an
y
o
be mounted
di
o
n, operation a
n
t
ion with adeq
u
surfaces, mini
m
lamp. The ligh
t
y
the projector i
n
o
ut by qualifie
d
a
nd frequency
o
y
earthed and t
h
p
es of dimmer
ap
i
mped or dam
a
N
ever pull out t
h
m
p glass with ba
r
w
ith a second
a
y
have become
a
ire after 30 mi
n
the projector,
d
on’t hesitate to
w
er, when th
e
3/24
E
OF TH
E
c
k there is no t
r
a
ler and do not
u
r
y locations. K
e
y
other liquids.
di
rectly on to in
f
n
d maintenanc
e
u
ate ventilation
,
m
um distance i
s
t
is harmful to t
h
n
any way.
d
personnel.
o
f power suppl
y
h
at electrical in
s
ap
paratus.
a
ged by sharp e
d
h
e plug by tugg
i
r
e hand.
a
ry safety fixin
g
visibly damag
e
n
utes operation
do not open t
h
consult your d
e
e
device no
t
E
PROJE
C
r
ansportation d
a
u
se the apparat
u
e
ep this device
f
lammable surf
a
e
by qualified p
e
,
at least 50cm
s
3m.
h
e eye.
y
match the po
w
t
allation confo
r
d
ges. Never le
t
i
ng the powe
r
-
c
g
. A safety cor
d
e
d to such an
e
is 45℃, when
h
e housing an
d
e
aler or manuf
a
t
in use or
b
C
TOR
a
mage before
u
u
s.
away from rai
n
a
ces.
e
rsonnel.
from adjacent
w
er requireme
n
r
ms to all relev
a
t
the power-cord
c
ord.
d
is suppli
e
d f
o
e
xtent that the
i
steady state is
a
d
never operat
e
a
cture
r
b
efore clean
u
sing the projec
t
n
and moistur
e
wall surfaces.
n
ts of the projec
t
a
nt standards.
come into conta
c
o
r this; it shoul
d
i
r effectiveness
a
chieved 60℃,
e
the projector
n
ingor any
m
t
or. Should the
r
e
, excessive he
a
Be sure
t
hat
n
t
or.
c
t with other cabl
e
d
be attached
a
is impaired, f
o
with the co
v
e
r
m
aintenan
c
r
e
a
t,
n
o
e
s.
a
s
o
r
r
s
c
e

4/24
INSTALL THE PROJECTOR
!
Safety Cord
Handle
Clamp
Digital
Control
Panel
Warning
Please run the safety cord
through two holes for safety.
Take 2 clamps and the safety cord out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to
each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the WARNING on the underside of
the base as shown above) To pass the SAFETY CORD through the HOLES for safety! Always ensure that the projector is firmly
anchored to avoid vibration and slipping whilst functioning. Always ensure that the structure that you are going to mount the projector
to is secure and strong enough to support the weight of a XR 1000 Framing
WARNING:
1. The projector MUST be lifted or carried by the HANDLES instead of clamps.
2. For safety the safety cord should afford 10 times the Projector’s weight.
FITTING THE LAMP
Lock the yoke before
fitting/replacing
the lamp. Just as Shown by
Figure 1, after Opening the cover
at the rear of the projector by
loosening 8 fastfit screws, you can
open the head. To adjust the lamp
as per Figure 2. Take out the lamp
as per the figure 3.
Before lamp installation, tighten its
power wires well. Lamp in and
out are opposite orders
Note: don’t touch the internal
surface of the reflector and the
burner of the lamp with bare hands
so as not to impair the beam
output.
Important: Always read
"Instructions for use" enclosed
with the lamp.
1.open the fan after unfastening
four scews on both sides
of the fan.
2.use cross screw driver
to loosen the tightening
screw on one side of the lamp
2.Take the lamp out after pushing
it downward after removing two lamp
wires on its other side.
Figure2：lamp adjustment 3.use cross screw driver
to adjust two screws to adjust
the lamp's position
1.unfasten the tightening
screw on one side of the
lamp
Figure 1：8 pcs of fastfit screws Figure3：Removal of Lamp

5/24
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Before connection with mains power, make sure that the voltage and frequency marked on the rating plate of the projector match what
are supplied. It is recommended that each projector be supplied separately so that they may be individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation conforms to all
relevant standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with
each wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the
projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. XLR plugs and sockets
mustn’t be connected in any way other than mentioned in the above figure. The XR330Framing accepts digital control signals in
protocol DMX512 (1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second
fixture’s DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX
terminator as shown in the figure below.
DMX Controller
DMX512
Input Output DMX teminator
Input Output Input

6/24
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This prevents
electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is then plugged
into the output socket on the last projector in the chain. The connections are illustrated below.
SETUP OPTIONS-PROJECTOR CONFIGURATION
W-DMXDMX
Projector configuration can be set conveniently via push button and LCD display.
Launch the projector and press button ENTER for more than 2 seconds to unlock the panel, the LCD will show the function menu of
the projector, each main menu has its submenus and each submenu has a specific function. For details, please see the
“OPERATION MENU” section.
Press button UP or DOWN if you want to browse through the various Setup Options.
Press button ENTER to save your settings or enter the submenu.
Press button UP or DOWN to change values(plus or minus)
Press button FUNC, it will return to the upper menu. If button FUNC not pressed, the default will show display status automatically.
TO SET THE DMX START ADDRESS
Each XR 330 Framing must be given a DMX start address so that the correct projector responds to the correct control signals. This
DMX start address is the channel number from which the projector starts to “listen” to the digital control information being sent out
from the controller. The XR 330 Framing has 3 DMX modes. There are standard mode ,short mode and extended mode. For
example standard mode has 34channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 035, No. 3 projector’s
address 051, No. 4 projector’s address069, and so on.
Launch the projector. Press button ENTER more than 2seconds to unlock panel.
Press button ENTER to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; after powered on next time, the default will be last value saved
Press button FUNC, it will return to the upper menu.
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2

7/24
STAND-ALONE MODE
Operate the projector without connecting with a controller, enable the master mode through the operation panel, the
projector will run in Stand-Alone mode automatically.
DMX address can be set at any number within 512.
MASTER/SLAVE MODE
Many projectors can run synchronously in the Master/Slave mode by linking them with each other. First,
connect the first fixture’s DMX output to the second fixture’s DMX input using XLR-XLR control cable and then connect the second
fixture’s DMX output to the third fixture’s DMX input, and so on until all projector are connected in this way. Eventually connect the
last fixture’s DMX output to a DMX terminator. Set 1st projector as the master and others are Slaves.
Start Addresses of all Slaves are 001; Operation mode of the Master can be set any mode for a Master’ and Slaves’ operation mode can
be set accordingly.
After Powered on, the group will run in Master/Slave Mode
Input Output DMX terminator
Master Slave Input
Input Output Input

8/24
OPERATION MENU
First Menu Secondary Menu Third Menu Fourth Menu
DMX Address DMX Address=XXX
Reset Are You Sure
Config Settings
DMX Mode
Standard
Extended
Short
Lamp Control
By Control Channe
l
By Power On
By DMX Present
Loss of DMX
When DMX is Lost
Normal time out
When DMX is Lost
Hold Last Value
Fan Operate Mode
Fan Operate Mode
Normal
Fan Operate Mode
Quieter
Fan Operate Mode
Hot Environment
Factory Settings
(Press button
DOWN/UP/ENTER at the same
time to enter the sub-menu)
Fixture Type
(WARNING: Never change the fixture
type ,otherwise the system will be
damaged!)
Option Settings
Color Positions
Color Positions
STEPPED
Color Positions
LINEAR
F-Gobo Positions
F-Gobo Positions
STEPPED
F-Gobo Positions
LINEAR
Pan DMX Invert
Pan DMX Invert
OFF
Pan DMX Invert
ON
Tilt DMX Invert
Tilt DMX Invert
OFF
Tilt DMX Invert
ON
Pan Tilt Swap
Pan Tilt Swap
OFF
Pan Tilt Swap
ON
Dimmer Invert
Dimmer Invert
OFF
Dimmer Invert
ON
Iris Invert
Iris Invert
OFF
Iris Invert
ON

9/24
Zoom Invert
Zoom Invert
OFF
Zoom Invert
ON
CYM Invert
CYM Invert
OFF
CYM Invert
ON
Defaults
Defaults
OFF
Defaults
Restore Defaults
Display Options
Display Mode
Display
On Always
Display
Off After Delay
Display Invert
Display Invert
OFF
Display Invert
ON
Display Dimming
Disp Dim Level
Min
Disp Dim Level
1
Disp Dim Level
2
Disp Dim Level
3
Disp Dim Level
4
Disp Dim Level
5
Disp Dim Level
6
Disp Dim Level
7
Disp Dim Level
8
Disp Dim Level
9
Disp Dim Level
Full
Display Contrast
Display Contrast
XX(1~21)
Information
Lamp Hours Lamp Hours=
XX
Reset Lamp Hours
Are You Sure(UP/DOWN)
Total Hours Total Hours=
XX
Temperature
Display Board Display Board=
XX℃
Driver Board 1 Driver Board 1=
XX℃
Driver Board 2 Driver Board 2=
XX℃
Driver Board 3 Driver Board 3=
XX℃
Driver Board 4 Driver Board 4=
XX℃
Pan and Tilt Pan and Tilt=
XX℃
Head Sensor Head Sensor=
XX℃
Software Version Display Board Display Board=
X.X.X

10/24
Driver Board 1 Driver Board 1=
X.X.X
Driver Board 2 Driver Board 2=
X.X.X
Driver Board 3 Driver Board 3=
X.X.X
Driver Board 4
Driver Board 4
=
X.X.X
Pan and Tilt Pan and Tilt=
X.X.X
View DMX Values DMX Channel
1=XXX
Electronic SN Electronic SN=
************
RDM Device Label
RDM Device Label
ANSI E1.20 RDM
Version X.X
Pan Encoder
Wiring Normal
Pan Err 0
Count 50880
Tilt Encoder
Wiring Normal
Tilt Err 0
Count 28080
Driver Faults
X Over Temp 0
Y Over Temp 0
X Fault 0
Y Fault 0
Test Modes
Factory Setup
Factory Setup
OFF
Factory Setup
ON
Self Test
Self Test
OFF
Self Test
ON
Lamp Manual Control
Lamp Status
On Command Sent
S= X C= X
Lamp On
Turn Lamp On
Turn Lamp Off
Wireless Options
Wireless Mode
Wireless Mode
XLRFirst
Wireless Mode
Wireless Only
Wireless Mode
XLR Only
Wireless Mode
Wireless To XLR
Wireless Mode
Wireless First
Un-Link Wireless Really Un-Link
Enter=Yes
Operation Mode
Operation Mod
e
=
DMX Mod
e
Operation Mode=
Master Mode
User’s Memory 1
User’s Memory 2
Preset Memory 1
Preset Memory 2

11/24
Preset Memory 3
Operation Mode=
Slave Mode
User’s Memory 1
User’s Memory 2
Preset Memory 1
Preset Memory 2
Preset Memory 3
Operation Mode=
Standalone Mod
e
User’s memory Edit user’s memory
User’s memory 1 Scene XX
（1~200scenes）
Shutters Shutters XXX
Dimmer Dimmer XXX
Slow Dimmer Slow Dimmer XXX
CYM Macro CYM Macro XXX
Cyan Cyan XXX
Yell ow Yell ow XX X
Magenta Magenta XXX
Color Wheel Color Wheel XXX
Iris Iris XXX
Iris Macro Iris Macro XXX
Fixed G-Wheel Fixed G-Wheel XXX
Rotating G-Wheel Rotating G-Wheel
XXX
Gobo Rotation Gobo Rotation XXX
G-Rotation slow G-Rotation slow XXX
Prism Out Prism Out XXX
Prism Rotation Prism Rotation XXX
Frost Frost XXX
Focus Focus XXX
Zoom Zoom XXX
Pan Pan XXX
Pan Fine Pan Fine XXX
Tilt Tilt XXX
Tilt Fine Tilt Fine XXX
Motors’ Speeds Motors’ Speeds XXX
（000~255）
Delay Delay XX
s
（0.25s~100min）
Shift to next scene Shift to scene
XXX（1~200）
User’s memory 2 Scene XX
（1~200scenes）
Shutters Shutters XXX
Dimmer Dimmer XXX
Slow Dimmer Slow Dimmer XXX
CYM Macro CYM Macro XXX
Cyan Cyan XXX
Yell ow Yell ow XX X
Magenta Magenta XXX
Color Wheel Color Wheel XXX
Iris Iris XXX
Iris Macro Iris Macro XXX
Fixed G-Wheel Fixed G-Wheel XXX
Rotating G-Wheel Rotating G-Wheel
XXX
Gobo Rotation Gobo Rotation XXX
G-Rotation slow G-Rotation slow XXX
Prism Out Prism Out XXX
Prism Rotation Prism Rotation XXX

12/24
Frost Frost XXX
Focus Focus XXX
Zoom Zoom XXX
Pan Pan XXX
Pan Fine Pan Fine XXX
Tilt Tilt XXX
Tilt Fine Tilt Fine XXX
Motors’ Speeds Motors’ Speeds XXX
（000~255）
Delay Delay XX s
（0.25s~100min）
Shift to next scene Shift to scene
XXX（1~200）
Single Scene
Shutters Shutters XXX
Dimmer Dimmer XXX
Slow Dimmer Slow Dimmer XXX
CYM Macro CYM Macro XXX
CMY Cyan Cyan XXX
CMY Yellow Yellow XXX
CMY Magenta Magenta XXX
Color Wheel Color Wheel XXX
Iris Iris XXX
Iris Macro Iris Macro XXX
Fixed G-Wheel Fixed G-Wheel
XXX
Rotating G-Wheel Rotating G-Wheel
XXX
Gobo Rotation Gobo Rotation
XXX
G-Rotation slow G-Rotation slow
XXX
Prism Out Prism Out XXX
Prism Rotation Prism Rotation
XXX
Frost Frost XXX
Focus Focus XXX
Zoom Zoom XXX
Pan Pan XXX
Pan Fine Pan Fine XXX
Tilt Tilt XXX
Tilt Fine Tilt Fine XXX
Motors’ Speeds Motors’ Speeds
XXX（000~255）
Clear User’s memory
User’s memory 1
Clear User’s memory
1？（Press buttons
2,3.4,ie buttons
UP/DOWN/ENTER to
execute the function）
User’s memory 1
cleared
User’s memory 2
Clear User’s memory
2？（Press buttons
2,3.4,ie buttons
User’s memory 2
cleared

13/24
UP/DOWN/ENTER to
execute the function）
Clear Single Scene
Clear single scene 1？
（Press buttons 2,3.4,ie
buttons
UP/DOWN/ENTER to
execute the function）
Single Scene 1
cleared
ERROR MESSAGES
In the course of launch, Projector examines automatically whether there are errors and if there are, it will display
information as follows:
Sensor Err S1-M1 Color wheel (1# drive board motor 1) error
Sensor Err S1-M2 CYM-Cyan (1# drive board motor 2) error
Sensor Err S1-M3 CYM-Yellow (1# drive board motor 3) error
Sensor Err S1-M4 CYM-Magenta(1# drive board motor 4) error
Sensor Err S2-M1 Rotating Gobo wheel (2# drive board motor 1) error
Sensor Err S2-M2 Gobo rotation (2# drive board motor 2) error
Sensor Err S2-M3 Framing module rotation- In (2 drive board motor 3) error
Sensor Err S3-M1 Focus (3# drive board motor 1) error
Sensor Err S3-M2 Zoom 1(3# drive board motor 2) error
Sensor Err S3-M4 Prism rotation (3# drive board motor 4) error
Over Temp Error Over Temp Error
Temp Sense Error Temp Sense Error
Head Fan 1 Fail Lamp Fan Fail
Head Fan2 Fail Head Fan1 Fail
Head Fan 3 Fail Gobo Fan Fail
Head Fan 4 Fail CMY Fan Fail
Pan Encoder Err Pan Encoder Err
Tilt Encoder Err Tilt Encoder Err
Pan Enc T Out Pan Enc T Out
Tilt Enc T Out Tilt Enc T Out
Pan Sensor Error Pan Sensor Error
Tilt Sensor Error Tilt Sensor Error
Pan Over Temp Pan Over Temp
Pan Driver Fault Pan Driver Fault
Tilt Over Temp Tilt Over Temp
Tilt Driver Fault Tilt Driver Fault
Pan Enc Rev Err Pan Enc Rev Err
Tilt Enc Rev Err Tilt Enc Rev Err

14/24
REPLACING GOBOS
rotator
gobo
garter spring
Replacement of rotating gobos:
disconnect from power, loosen the
four fastfit screws of the side cover
like figure 1, pull out the rotators
by finger as figure 2.
figure 1
figure 2
rotator
rotating gobo wheel

Dimmer Fine
Dimmer
MODE
EXTENDED
MODE
STANDARD
MODE
SHORT
15/24
DMX PROTOCOL
FUNCTION DMX DESCRIPTION
1 1 1 Strobe
000-010 Close
011-025 Open
026-225 Strobe speed from slow to fast
226-239 Macro 1
240-241 Macro 2
242-246 Macro 3
247-255 Open
2 2 2 000-003 Close
004-255 Linear dimming（0-100%）
3 3 0-255 Dimmer in 16 bit
3 4 4 CYM Macro
000-016 White
017-035 Yellow+ Magenta=Red
036-054 Yellow
055-073 Yellow +Cyan=Green
074-092 Cyan
093-110 Cyan + Magenta= Violet
111-128 Magenta
129-255 CYM color mixing from slow to fast
4 5 5 Cyan 000-255 Cyan (linear 0~100%)
6
Cyan in 16 Bit 000-255 Cyan 16 Bit
5 6 7 Yellow 000-255 Yellow (linear 0~100%)
8
Yellow in 16 Bit 000-255 Yellow in 16 Bit
6 7 9 Magenta 000-255 Magenta (linear 0~100%)
10
Magenta in 16 Bit 000-255 Magenta in 16 Bit
7 8 11 Color Wheel
000-008 White
009-016 Color 1
017-024 Color 2
025-032 Color 3
033-040 Color 4
041-048 Color5
049-056 Color6
057-064 Color7
065-073 Color8
074-082 Color9
083-091 Color10
092-100 Color11
101-109 Color12
110-118 Color13
119-128 CTO
129-191 Rotation ,Clockwise from slow to fast
192-255 Rotation, Anti-clockwise from slow to fast

8 9 12
13
16/24
Iris 000-255 From Big to Small In size
Iris Fine 000-255 Iris in 16 Bit
9 10 14 Iris Macro
000-010 White
011-072 Iris Effect 1
073-136 Iris Effect 2
137-198 Iris Effect 3
199-214 Iris Effect 4
215-222 Iris Effect 5
223-230 Iris Effect 6
231-255 Fully Open
10 11 15 Rotating Gobo
Wheel l
000-012 White
013-025 Gobo 1
026-037 Gobo 2
038-050 Gobo 3
051-062 Gobo 4
063-075 Gobo 5
0760-88 Gobo 6
089-101 Gobo 7
102-114 Gobo 8
115-127 Gobo 9
128-155 Rotation （clockwise From slow to Fast）
156-183 ReverseRotation （anti-clockwise From slow to Fast）
184-191 Shake of Gobo 1
192-199 Shake of Gobo 2
200-207 Shake of Gobo 3
208-215 Shake of Gobo 4
216-223 Shake of Gobo 5
224-231 Shake of Gobo 6
232-239 Shake of Gobo 7
240-247 Shake of Gobo 8
248-255 Shake of Gobo 9
11 12 16 Gobo Rotation
000-128 Gobo Indexing(0~540degrees)
129-188 Rotation （Clockwise From slow to Fast）
189-195 Stop
196-255 Rotation （Anti-Clockwise From slow to Fast）
13 17 Gobo Rotation
Fin
e
0-255 Gobo Rotation in 16 Bit
12 14 18
Framing Blade1
(Left)
000-255 Linear light spot from big to small(blade
1/left)
19 000-255 Light spot 16 bit precision(blade 1/left)
13 15 20 Framing Blade1
(right)
000-255 Linear light spot from big to small(blade
1/right)
21 000-255 Light spot 16 bit precision(blade 1/right)
14 16 22 Framing Blade2
(Left)
000-255 Linear light spot from big to small(blade
2/left)
23 000-255 Light spot 16 bit precision(blade 2/left)

17/24
15 17 24 Framing Blade2
(right)
000-255 Linear light spot from big to small(blade
2/right)
25 000-255 Light spot 16 bit precision(blade 2/right)
16 18 26 Framing Blade3
(Left)
000-255 Linear light spot from big to small(blade
3/left)
27 000-255 Light spot 16 bit precision(blade 3/left)
17 19 28 Framing Blade3
(right)
000-255 Linear light spot from big to small(blade
3/right)
29 000-255 Light spot 16 bit precision(blade 3/right)
18 20 30 Framing Blade4
(Left)
000-255 Linear light spot from big to small(blade
4/left)
31 000-255 Light spot 16 bit precision(blade 4/left)
19 21 32 Framing Blade4
(right)
000-255 Linear light spot from big to small(blade
4/right)
33 000-255 Light spot 16 bit precision(blade 4/right)
20 22 34 Framing module
0°~90°rotation
000-255 Framing module 0°~90°rotation
23 35 000-255 Rotation 16 bit precision
21 24 36 Three-Facet
Prism
000-016 White
017-255 Prism
22 25 37
Prism Rotation
000-128 Prism Indexing
129-191 Rotation(Clockwise from slow to fast)
192 Stop
193-255 Rotation(Anti- Clockwise from slow to fast)
23 26 38 Frost Filter 000-255 Linear Frost
24 27 39 Focusing 000-255 Linear Focusing
40
Focusing Fine 000-255 Focusing in 16 bit precision
25 28 41 Zoom 00
0
-
255 Linear Zooming
42
Zooming Fine 00
0
-
255 Linear Zooming in 16 bit precision
26 29 43 Pan 000-255 Pan(0°~540°)
30 44 Pan Fine 000-255 Pan in 16 bit precision
27 31 45 Tilt 000-255 Tilt(0°~270°)
32 46 Tilt Fine 000-255 Tilt in 16 bit precision
33 47
Pan & Tilt Speeds 000-255 Pan & Tilt Speed from Fast to Slow
28 34 48 Control
000-047 Reserved
048-080 Reset
081-112 Reserved
113-144 Lamp Off ( Delay for 3 s)
145-168 Reserved
169-200 Lamp Half Power
201-223 Reserved
224-255 Lamp Full Power
Remark: Prism is prior to Frost

18/24
LED INDICATION
Green
On DMX signal OK
Off No DMX signal
Flash DMX signal error
Yellow On Setting the panel
Blue On Power
Red/Green Red Slave mode or Self-Test Mode
MAINTENANCE
If the projector’s lens becomes damaged or broken it should be replaced. If the lamp becomes damaged or deformed in any way it
must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should
be changed at once, aged lamps run to the extremity of their life might explode. If the projector does not function, check the fuses on
the power socket of the projector, they should only be replaced by fuses of the same specification. The projector has overheat
protection device that will switch off the projector in case of overheating. Should it happen, check if the fans are blocked or not, or if
they are dirty, clean them before switching on the projector again.
Any maintenance work should only be carried out by qualified technicians.
LUBRICATION
To ensure the smooth rotation of the rotating gobos and movement of the lens for focusing, it is recommended that the bearings for
the rotating gobos and the 2 sliding tracks for the focusing lens holder be lubricated every two months. Use only high quality,
high-temperature grease .
KEEPING THE PROJECTOR CLEAN
To ensure the reliability of the projector it should be kept clean. It is recommended that the fans should be cleaned every 15 days.
The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output. Do NOT use any type of
solvent containing chemical elements on dichroic colour filters.
Cleaning frequency depends on the environment in which the fixture operates. A soft cloth and typical glass cleaning products
should be used in cleaning. It is recommended to clean the external optics at least once every 20 days and clean the internal optics at
least once every 30 / 60 days.
Do not use any organic solvent, e.g. alcohol, to clean the reflectormirror, dichroic colour filters or housing of the apparatus.
TROUBLESHOOTING
PROBLEM ACTION
The projector doesn’t switch on ¾Check the fuse on the power socket.
¾Check the lamp.
The lamp is on but the projector doesn’t respond
to the controller
¾Make sure that the fixture’s start address is right
¾Replace or repair the XLR signal cable.
The projector functions intermittently ¾Make sure the fan is working well or fans and their shields are not blocked
Beam appears dim, Low in brightness ¾Make sure the lamp is within its lifespan
¾Remove dust or grease from the lenses.
The project image appears to have a halo ¾Carefully clean the lamp, optical lenses and other components.
Heavily Defective Beam ¾Check if lens are in good condition(not cracked)
¾Clean dust or grease on the lens.

5-100% linearly adjustable with Macros
FROST:
IRIS:
Bi-directionally rotatable, and shakable at variable speeds
ROTATING GOBO WHEEL:
FRAMING MODULE:
COLORS:
Manufacturers Rated Lamp Life 1500 hours
Stepping/Linear color changing
1 Framing module: 4 framing blades
Rainbow effect with bi-directional and variable speeds
1 color wheel: 14colors+ open
SIRIUS HRI 330W XL
19/24
TECHNICAL DATA
VOLTAGES:
100V~240V AC，50/60Hz
POWER CONSUMPTION:
450W@220V
LAMP:
OSRAM
Colour Temperature 7500K
CMY linear mixing system with macros
0°~90°rotation ,images at different sizes and shapes, curtain effect.
1 Rotating gobo wheel:
9 interchangeable gobos+1white
Gobo diameter: Φ14.8mm
Gobo image diameter: Φ8mm
PRISM:
1pc,3-facet rotating Prism(bi-directional with variable speeds)
1pc frost filter
FOCUSING:
DMX linear Focusing
ZOOMING:
DMX linear Zooming
DIMMER/STROBE:

GROSS WEIGHT(in Flight Case):
DMX512, 3 pins and 5 pins interfaces
20/24
0-100% linearly adjustable/ Double shutter blades, 0.3~25 F.P.S
HEAD MOVEMENT:
Pan 540º, Tilt 270º with auto position correction
BEAMANGLE:
3.8°-35°, Linear Adjustment
CONTROL:
28channels in short mode, 34channels in standard mode and 48channels in extended mode
Self-test mode
OTHER FUNCTIONS:
Adjustable Pan & Tilt speed
Modular Structure for easy maintenance
DMX512 wirless signal
Optional DMX512 Transmitter
HOUSING:
High temperature ABS, IP20
NETWEIGHT:
22.5Kg
80Kg in flight case(2pcs/case) and accessories
27Kg in carton(1pc/ctn) and
SIZES: