PROAIM FF-WRLS-DR User manual

Drive Wireless Follow Focus
(FF-WRLS-DR)
I N S T R UC T I O N M A NU AL
All rights reserved
No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permitted by
the applicable copyright statutes or in writing by the Publisher.

PROAIM DRIVE WIRELESS FOLLOW FOCUS 2
INTRODUCTION
Proaim presents its exclusive wireless Follow Focus that allows you to set up a wireless lens
control system on your camera equipped with a geared lens and either 15mm or 19mm support
rods. It assists the camera operators in adjusng the focus or focal distance (zoom) of the camera
shoong remotely. The Wireless Follow Focus can be used along with matching camera control
gear like DSLR rigs, sliders, Steadycam kits, cranes/ jibs / dolly, Easy Rigs etc. The high torque
motor and a fast reacon speed allows to keep your subject in focus no maer how it moves.
The High grade controller features four memory buons to record dierent focusing points that
can be used repeatedly and also can be randomly switched and combined wilfully.
CONTENTS OF SHIPPING BOX:
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below.
Controller
Quick lock
Buon Quick lock Buon
with Servo motor
9V baery charger 2 x baery
Follow focus
gear ring
2x universal black
plug
Screw driver
2 x Drive gear
2x Anteena
Baery charger
Receptor

PROAIM DRIVE WIRELESS FOLLOW FOCUS 3
ASSEMBLING OF PROAIM DRIVE WIRELESS FOLLOW FOCUS
Controller power switch & receiver power
switch:
 Controller power light is on for 2 seconds,
then o; red power light and green signal
light of the receiver are always on.
NOTE: To set frequency, press FREQ buon
the light starts to cycle through colors. Stop
on preferred color. Repeat for each unit,
matching the colors. Verify DATA light is solid
green.
Frequency: 433-434 MHz (US 900MHz)
Memory keys use methods:
 Adjust the focus wheel or dial to the
desired focus point and press the
memory buon 1 for 3 seconds; if the
indicator light on the buon is on and red
signal is blink for a while, it indicates the
success of this focus memory the move to
the next focus memory. At the same
me, press memory key 2,3 and 4, to
respecvely record the focus.
Applicable occasions:
 Wireless follow focus can completely zoom widely in steadicam movement lens and the or-
bital moon lens.
Note:
 It may be insensive in operaon, because the baery voltage is too low. Please replace the
baery mely.
 Infrared shuers are divided into canon and Nikon. Tell the customer service sta about your
camera model when purchase.
 Insert the Anteena onto the Controller and Receptor.

PROAIM DRIVE WIRELESS FOLLOW FOCUS 4
The dial funcon:
 When adjust the desired focus the focus
posion can be recorded manually by
engraving lines.
Infrared wireless shuer funcon:
 Only suitable for canon and Nikon
cameras.
Playback speed adjustment key :
 Uses the memory buon to switch the
focus and adjust speed. Adjusng the
speed knob can change the speed of the
motor (with the memory eect, dierent
shoong eects can be achieved and
speed can be changed during zoom).
Install the camera and follow focus ring:
 Mount the camera to head and install the focus ring on the lens focus ring.

PROAIM DRIVE WIRELESS FOLLOW FOCUS 5
The receptor and quick lock buon
installaon
 Aach the quick lock buon with
receptor with the help of screws and
ghten the screws with the help of
screw driver.
 Install receptor and quick lock buon : loosen the knob of quick lock buon and mount it onto
the 15mm rods.
Note : Infrared emission lights of the receiver should be aligned infrared receiver side of the SLR
cameras, or the infrared shuer does not work.
 Loosen the side knob of quick lock buon with motor and mount it on 15mm rods. Now
ghten the side knob to secure.
ATTACHING QUICK LOCK BUTTON WITH MOTOR

PROAIM DRIVE WIRELESS FOLLOW FOCUS 6
 Loosen the boom knob and adjust the
gear to match with the follow focus ring.
 Insert motor assembly power cord into
receiver outlet.
YOUR PROAIM DRIVE WIRELESS FOLLOW FOCUS
ALL DRESSED UP AND GOOD TO GO
(SHOWN WITH OTPIONAL ACCESSORIES)

PROAIM DRIVE WIRELESS FOLLOW FOCUS 7
WARRANTY
We oer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
crasmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
dues are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequenal damages resulng from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers aer the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. Aer that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without rst geng a response and geng the approval to send back
the item.
In case of any kind of dissasfacon, we urge you to Contact us immediately and we shall do our
Best to help you out. For any other assistance you can reach us via email.
For any other assistance you can reach us via email.