Promeba PB-420 Series User manual

USER GUIDE
STRETCHER SUPPORT // PB-420 SERIES
Review 01/15

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
3
01 INTRODUCTION
01.1 Using this manual 05
01.2 Technical data sheet 06
02 INSTALLATION
02.1 Transport and unpacking 11
02.2 Anchorage points 12
03 OPERATION
03.1 Commands 15
03.2 Elements of the manual system 21
03.3 Loading and unloading operation 23
03.4 Scoop stretcher fastening 24
03.5 Spine board fastening 24
03.6 Tensors 25
04 MOUNTING AND COMPONENTS
04.1 Main exploded view SERIE PB-420 27
04.2 Main exploded view PB-420 28
04.3 Main exploded view PB-420/1 30
04.4 Main exploded view PB-420/2 32
04.5 Main exploded view PB-420/3 34
04.6 Main exploded view PB-420/4 36
05 GENERAL MAINTENANCE 38
06 LEGAL NOTICES 39
07 PRODUCT WARRANTY 40
INDICE
MODEL PB420
WITH LODGING FOR SCOOP STRETCHER
OR SPINAL BOARD AND LATERAL SHIFT
MODEL PB420/1
WITH LATERAL SHIFT
MODEL PB420/2
WITH LODGING FOR SCOOP
STRETCHER OR SPINE BOARD
MODEL PB420/3
BASIC FIXED PLAN
MODEL PB420/4
DOUBLE BASIC FIXED
PLAN WITH LODGING
FOR SCOOP STRETCHER
AND SPINAL BOARD

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
5
01.1 Using this manual
This manual provides using and maintenance instruc-
tions of the product, as well as the way of xing minor
faults that could appear.
It is recommended before the operation of the product
to read carefully this manual in order to avoid damages
caused by a misuse.
Do not lose this document, it should be accessible to
any doubt that could appear by medical personnel.
Remember that a good use and maintenance are ne-
cessary for the proper operation of the product.
Each product incorporates an identication sticker with
the serial number and the model. Keep these numbers
so that they can be indicated to the dealer if necessary.
01 INTRODUCTION

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
6
01 INTRODUCTION
01.2 Technical data sheet
MEASURES AND FEATURES // PB-420
LENGHT 2090 mm SIDE MOVEMENT 300 mm
WIDTH 600 mm MAX. LOAD 220 Kg
HEIGHT 170 mm
WEIGHT 45 Kg
170
600
2090

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
7
MEASURES AND FEATURES // PB-420/1
LENGHT 2010 mm SIDE MOVEMENT 300 mm
WIDTH 600 mm MAX. LOAD 220 Kg
HEIGHT 70 mm
WEIGHT 40 Kg
01 INTRODUCTION
70
600
2010

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
8
01 INTRODUCTION
MEASURES AND FEATURES // PB-420/2
LENGHT 2025 mm WEIGHT 42 Kg
WIDTH 600 mm MAX. LOAD 280 Kg
HEIGHT 100 mm
2025
100
600

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
9
01 INTRODUCTION
MEASURES AND FEATURES // PB-420/3
LENGHT 2010 mm WEIGHT 35 Kg
WIDTH 600 mm MAX. LOAD 280 Kg
HEIGHT 55 mm
600
55
2010

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
10
01 INTRODUCTION
MEASURES AND FEATURES // PB-420/4
LENGHT 2020 mm WEIGHT 45 Kg
WIDTH 600 mm MAX. LOAD 220 Kg
HEIGHT 200 mm
600
2020
200

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
11
02.1 Transport and unpacking
First carefully remove the packaging to prevent the da-
mage of the outside of the stretcher support.
1. Transport with a crane (high load)
· Thread tapes through the upper platform for its trans-
port (as shown in graphs)
· Transport the load level following all the precepts and
regulations for the transport of suspended loads.
2. Transport with a forklift
· Place a pallet or a at surface under the bench and
transport it transversely.
· Do not load the bench directly on the forklift without
a pallet or a at support surface.
· Do not load the bench longitudinally on the forklift if
a suciently long base is not available.
· Every bench has been thoroughly inspected leaving
the factory. To ensure that it hasn’t been damaged du-
ring the transport, it is requested to carefully examine
the interior and exterior, and in case of nding any da-
mage, communicate immediately to the installer.
· The bench should be levelled for an optimum perfor-
mance.
02 INSTALLATION
TRANSPORT WITH A CRANE
FIX THE TAPES TO LEVEL THE LOAD WEIGHT
TRANSPORT WITH A FORKLIFT
USE ALWAYS A FLAT SUPPORT SURFACE

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
12
02 INSTALLATION
02.2 Anchore points
Before putting the bench into operation, ensure that
each and every anchorage points are placed and
clasped.
ANCHORAGE FOR STRETCHER SUPPORT PB420
(8 anchorage points)
ANCHORAGE FOR STRETCHER SUPPORT PB420/1
(8 anchorage points)
1274 102102
12,5
159
1274 102 102
12,5
159

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
13
02 INSTALLATION
ANCHORAGE FOR STRETCHER SUPPORT PB420/2
(10 anchorage points)
ANCHORAGE FOR STRETCHER SUPPORT PB420/3
(10 anchorage points)
ANCHORAGE FOR STRETCHER SUPPORT PB420/4
(10 anchorage points)
800
522
400 250 150
11
800400 250
522
150
11
522
400 800 250 150
11

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
15
03.1 Commands PB-420
1. Stainless steel ramp
2. Lodging for scoop stretcher
3. Ramp gradient regulator
4. Lateral shift base
5. Lateral shift operation lever
1
4
2
3
5
1 2 3 4 5
03 OPERATION

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
16
03.1 Commands PB-420/1
1. Stainless steel ramp
2. Lateral shift base
3. Lateral shift operation lever
1 2 3
1
2
3
03 OPERATION

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
17
03.1 Commands PB-420/2
1. Stainless steel ramp
2. Lodging for scoop stretcher
3. Ramp gradient regulator
1 2 3
1
2
3
03 OPERATION

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
18
03.1 Commands PB-420/3
1. Stainless steel ramp
1
1
03 OPERATION

USER GUIDE // STRETCHER SUPPORT PB-420 SERIES
Review 01/15
19
03.1 Commands PB-420/4
1. Stainless steel ramp
2. Lodging for scoop stretcher
3. Lodging for spine board
4. Ramp gradient regulator
1
2
4
3
1 2 3 4
03 OPERATION