Promeba PC-750 Series User manual

USER GUIDE
ELECTRIC STRETCHER SERIE PC-750 //
STRETCHER SUPPORT SERIE PB-720
Review 01/16

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
3
01 INTRODUCTION
01.1 Using this manual 05
01.2 Technical data sheet 06
02 INSTALLATION
02.1 Transport and unpacking 10
02.2 Anchorage points 11
02.3 Connection to the mains power supply 12
02.4 Stretcher’s launch 13
03 OPERATION
03.1 Commands of the support PB-720 14
03.2 Commands of the support PB-725 15
03.3 Commands of the stretcher PC-750 16
03.4 Commands of the stretcher PC-755 17
03.5 Elements of the manual system PB-720 / PB-725 18
03.6 Elements of the manual system PC-750 / PC-755 19
03.7 Loading and unloading operation 20
03.8 Control panel 21
03.9 Breakdowns 22
03.10 Troubleshooter 23
04 MOUNTING AND COMPONENTS
04.1 Main exploded of stretcher PC-750 / PC-755 24
04.2 Main exploded of support PB-720 / PB-725 25
04.3 Bill of lower ensamble PC-750 / PC-755 26
04.4 Exploded views of lower ensamble PC-750 / PC-755 27
04.5 Bill of upper ensamble PC-750 28
04.6 Exploded views of upper ensamble PC-750 31
04.7 Bill of upper ensamble PC-755 32
04.8 Exploded views of upper ensamble PC-755 33
04.9 Bill of control panel set PC-750 / PC-755 34
04.10 Exploded views of control panel set PC-750 / PC-755 35
04.11 Bill of extensible frame set PC-750 / PC-755 36
04.12 Exploded views of extensible frame set PC-750 / PC-755 37
04.13 Bill of batteries cabinet set PC-750 / PC-755 38
04.14 Exploded views of batteries cabinet set PC-750 / PC-755 39
04.15 Bill of left handrail ensamble PC-750 40
04.16 Exploded views of left handrail ensamble PC-750 41
04.17 Bill of right handrail ensamble PC-750 42
04.18 Exploded views of right handrail ensamble PC-750 43
04.19 Bill of headrest set of stretcher’s loading PC-750 / PC-755 44
04.20 Exploded views of headrest set of stretcher’s loading PC-750 / PC-755 45
04.21 Bill of stretcher’s bed set PC-750 46
04.22 Exploded views of stretcher’s bed set PC-750 47
INDEX

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
4
04.23 Bill of platform ensamble PB-720 48
04.24 Exploded views of ensamble platform PB-720 49
04.25 Bill of platform ensamble PB-725 50
04.26 Exploded views of platform ensamble PB-725 51
04.27 Bill of supplement ensamble PB-720 52
04.28 Exploded views of supplement ensamble PB-720 53
04.29 Bill of xed support stretcher system PB-720 54
04.30 Exploded views of xed support stretcher system PB-720 55
04.31 Bill of xed support stretcher system PB-725 56
04.32 Exploded views of xed support stretcher system PB-725 57
04.33 Bill of removable support stretcher system PB-720 / PB-725 58
04.34 Exploded views of removable support stretcher system PB-720 / PB-725 61
04.35 Bill of set plate references PB-720 / PB-725 62
04.36 Exploded views of set plate PB-720 / PB-725 63
04.37 Bill of anchor point set references PB-720 / PB-725 64
04.38 Exploded views of anchor point set PB-720 / PB-725 65
04.39 Bill of loading head set references PB-720 / PB-725 66
04.40 Exploded views of loading head set PB-720 / PB-725 67
05 ELECTRICAL CIRCUIT DIAGRAM
05.1 Printed circuit board 68
05.2 Electrical wiring diagram 69
06 GENERAL MAINTENANCE 71
07 LEGAL NOTICES 72
08 PRODUCT WARRANTY 73
MODEL PC-750
STANDARD STRETCHER
MODEL PC-755
INCUBATOR STRETCHER
MODEL PB-720
SUPPORT WITH CABINET FOR
SCOOP STRETCHER
MODEL PB-725
SUPPORT WITHOUT CABINET
FOR SCOOP STRETCHER
INDEX

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
5
01.1 Using of manual
The manual provides using and maintenance instruc-
tions of the product, as well as the way of xing minor
faults that could appear.
It is recommended before the operation of the product
to read carefully this manual in order to avoid damages
caused by a misuse.
Do not lose this document, it should be accessible to
any doubt that could appear by medical personnel.
Remember that a good use and maintenance are ne-
cessary for the proper operation of the product.
Each product incorporates an identication sticker with
the serial number and the model. Keep these numbers
so that they can be indicated to the dealer if necessary.
01 INTRODUCTION

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
6
01.2 Technical data sheet
MEASUREMENTS AND FEATURES // PC-750 STANDARD STRETCHER
LENGHT 2000 mm POWER SUPPLY 12 V. CC.
WIDTH 590 mm USING UP POWER 48A
HEIGHT MIN/MAX 420-1300 mm TRENDELEMBURG 30º
FOWLER 17º INCLINATION OF THE BACK 75º
WEIGHT 72 Kg LOAD HEIGHT 920 mm
MAX. LOAD 300 Kg LOADING TIME 120 min
OP. TEMPERATURE -20º/+40º OPERATOR REQUIRED 2
01 INTRODUCTION

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
7
MEASUREMENTS AND FEATURES // PC-755 INCUBATOR STRETCHER
LENGHT 2000 mm POWER SUPPLY 12 V. CC.
WIDHT 575 mm USING UP POWER 48A
HEIGHT MIN/MAX 390-1270 mm OPERATOR REQUIRED 1
WEIGHT 65 Kg LOAD HEIGHT 920 mm
MAX. LOAD 300 Kg LOADING TIME 120 min
OP. TEMPERATURE -20º/+40º TRAY MESUREMENTS 1765x525 mm
01 INTRODUCTION
575
2000
1765
525
390
235
1110
1270
2375
375

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
8
MEASUREMENTS AND FEATURES // PB-720 SUPPORT WITH CABINET
LENGHT 2000 mm POWER SUPPLY 12 V. CC.
WIDHT 590 mm USING UP POWER 48A
HEIGHT MIN/MAX. 420-1300 mm TRENDELEMBURG 30º
FOWLER 17º INCLINATION OF THE BACK 75º
WEIGHT 120 Kg LOAD HEIGHT 920 mm
MAX. LOAD 300 Kg LOADING TIME 120 min
OP. TEMPERATURE -20º/+40º OPERATOR REQUIRED 2
6001970
1340
2040
01 INTRODUCTION

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
9
MEASUREMENTS AND FEATURES// PB-725 SUPPORT WITHOUT CAB.
LENGHT 2000 mm POWER SUPPLY 12 V. CC.
WIDHT 575 mm USING UP POWER 48A
HEIGHT MIN/MAX 390-1270 mm OPERATOR REQUIRED 1
WEIGHT 80 Kg LOAD HIGHT 920 mm
MAX. LOAD 300 Kg LOADING TIME 120 min
OP. TEMPERATURE -20º/+40º TRAY MESUREMENTS 1765x525 mm
1959
2030
600
1340
01 INTRODUCTION

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
10
02 INSTALLATION
02.1 Transport and unpacking
First carefully remove the packaging to prevent the da-
mage of the product. Take the wooden cover away and
use a crane to move vertically.
1. Transport with a crane (high load)
· Thread tapes through the upper platform for its trans-
port (as shown in graphs).
· Transport the load level following all the precepts and
regulations for the transport of suspended loads.
2. Transport with a forklift
· Place a pallet or a at surface under the stretcher su-
pport and transport it transversely.
· Do not load the stretcher support directly on the fork-
lift without a pallet or at support surface.
· Do not load the support stretcher longitudinally on
the forklift if a suciently long base is not available.
· Every set has been throughly inspected leaving the
factory. To ensure that it has not been damaged during
the transport, it is requested to carefully examine the
interior and exterior, and in case of nding any dama-
ge, communicate immediately to the installer.
· The stretcher and support set should be levelled for an
optimum performance.
TRANSPORT WITH A CRANE
FIX THE TAPES TO LEVEL THE LOAD WEIGHT
TRANSPORT WITH A FORKLIFT
USE ALWAYS A FLAT SUPPORT SURFACE

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
11
02 INSTALLATION
02.2 Anchorage points
Before putting the stretcher support into operation,
ensure that each and every anchorage points are pla-
ced and clasped.
ANCHORE FOR PB-720 · PB-725
(8 anchorage points)
180mm MÍNIMO
441mm MÁXIM
185
592
102
102 1274
159
2042
256
12,5 (X8)
LIMIT AMBULANCE FLOOR
FREE ZONE TO THE FLOOR
LIMIT AMBULANCE WALL
***IMPORTANT TO ITS INSTALLATION***
SREWS TO ATTACH ON THE FLOOR M12 S/NORMA DIN-7991 (8 UNITS)
BEFORE DRILLING ON THE FLOOR OF THE AMBULANCE, VERIFY THAT THE LATE-
RAL MOVEMENT OF THE STRETCHER SUPPORT ARE PLACED ON 0 POSITION.
KEEP THE MINIMUM LIMITS INDICATED ON THE PLAN AND ENSURE OF AFFIXING
THE SET ON THE REINFORCED CHASSIS AREA.
THE ELECTRIC INSTALLATION OF THE SET MUST BE COMPLETED WITH THE ELEC-
TRICAL SYSTEM OF THE AMBULANCE DISCONNECTED.
READ THE INSTRUCTIONS MANUAL IN CASE OF ANY DOUBTS DURING THE INSTALLATION.
USE SCREWS DIN-7991 - M12 - 10.9

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
12
02 INSTALLATION
02.3 Connection to the mains power supply PB-720 / PB-725
To make the connection follow the steps below.
Be particularly careful when the connecting the stretcher support to the required voltage of 12V and
do not leave cables in passageways and or moving elements. It can provoke breakages, cuts and
system failures.
A
Current cable 12V. CC.
Remove the plastic end of the BROWN
(+) y BLUE (-) cables with a thread pee-
ler to make the connection.
C
Use a power strip and a athead srew-
driver to connect the BROWN (+) y
BLUE (-) wires together with the outlet
of the ambulance.
To make the connection locate the black cable placed on the front side of the
support stretcher.
MAKE SURE YOU HAVE THE POWER LINE PROPERLY PROTECTED AND ENSURE THE POWER
ALONG THE LINE IS STABLE.
B

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
13
02 INSTALLATION
02.4 Stretcher’s launch PC-750 / PC-755
In order to start to use the electric stretcher, it is necessary to charge the batteries. For that, locate the
box in the back of the stretcher according to the photo (A) and open the frontal cover by the lock.
Pull two batteries out and pressuring the trigger in the frontal of the bases of the anchor as it is shown
at photo (B), move the battery to the left and remove it.
Straightaway charge to the maximum the two batteries with their PROMEBA’s charger supplied.
(APPROXIMATELY 30 MIN. ARE ENOUGH)
A
Charge only the batteries of the stretcher with the charger supplied by PROMEBA, otherwise the
batteries could be damaged and lose their guarantee.
B
External charger for PROMEBA’s batteries. High-performance battery for PROMEBA’s stretcher.

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
14
03.1 Commands of the SUPPORT PB-720
1. Removable handle to pull the support
2. Anchor point to lock the stretcher
3. Accomodation cabinet for scoop stretcher
4. Loading point for stretcher
5. Central hooks for stretcher
6. Removable lateral lever for folding the stretcher support
7. Removable bearing for stretcher support
8. Pull handle the rail from inside the ambulance
9. Guides for engagement operation
10. Lever to movement side
11. Safety hooks to grip the stretcher
03 OPERATION
4
7
10
1
2
6
8
10 4 2
3
9
5
11

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
15
03 OPERATION
03.2 Commands of the SUPPORT PB-725
1. Removable handle to pull the support
2. Anchor point to lock the stretcher
3. Loading point for stretcher
4. Central hooks for stretcher
5. Removable push botton to fold the support stretcher
6. Removable bearing for stretcher support
7. Pull handle the rail from inside the ambulance
8. Guides for engagement operation
9. Lever to movement side
10. Safety hooks to grip the stretcher
11. Support unit extra low
3
6
9
1
2
5
7
9 3 11
8
4
10
11

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
16
03.3 Commands of the STRETCHER PC-750
1. Foldable and reclining handrails
2. Retractable belts on the backrest
3. Touch control panel in the middle
4. Batteries cabinet with lock
5. Four lockable wheels
6. Telescopic frame for maneuvering
7. Bed with fowler and trendelemburg
8. Folding and adjustable IV pole
9. Powerful LED lighting on the sides
10. Emergency switch
11. Belts with front locking push botton
12. Automatic integrated charging system
2
5
11
3
8
4
1
6
03 OPERATION
7
9
10
12
71012

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
17
03 OPERATION
03.4 Commands of the INCUBATOR STRETCHER PC-755
1. Stainless steel tray for incubator
2. Touch control panel in the middle
3. Batteries cabinet with lock
4. Four lockable wheels
5. Telescopic frame for maneuvering
6. Powerful LED lighting on the sides
7. Emergency switch
8. Automatic integrated charging system
4
1
2
3
5
6
7
8
578

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
18
1640
300
03 OPERATION
03.5 Elements of the manual system
SUPPORT PB-720 / PB-725
LATERAL DISPLACEMENT
Hand lever
Operate the lever located on the rear of the right side
of the support, making a slight eort with foot and ac-
companing that movement by sliding with hands.
The total lateral displacement is 300 mm.
LONGITUDINAL DISPLACEMENT
Hand lever
Operate the lever located on the front of the right side
of the support by applying a slight eort with the foot
and accompanying this movement by sliding your
hands.
The total longitudinal displacement is 1640 mm.
IMPORTANT:
To load the stretcher, the support stretcher ALWAYS
must be placed totally pull out of the ambulance.

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
19
03.6 Elements of the manual system
STRETCHER PC-750 / PC-755
03 OPERATION
Foldable and reclining handrails
Stretch the lateral knob to fold the handrail or
pressure on red botton to recline.
Batteries cabinet with lock
To open the batteries cabinet, use the lock with
the key provided.
Bed with fowler and trendelemburg position
The bed set has two red buttons for adjust the
position.
Adjust the backrest inclination
Have 6 positions. Pressure the red handle and
accompany the backrest to desire position.
Four lockable wheels
Spin the red handle to block or unblock the turn
of the stretcher’s wheels.
Folding and adjustable IV pole included
Spin the wing nut to raise the IV pole and twirl
the upper ring. Unfold it.
Adjust maximum high of the stretcher
To adjust the maximum high of the stretcher loo-
sen the screw and spin to desired position.
Telescopic frame
Place the backrest in the vertical position, trigger
by lateral knob and pull out or close the frame.
Powerful LED lighting on the sides
Press the button LIGHTS from control panel for
activate the lights in the blinking or xed mode.
1
4
7
2
5
8
3
6
9
Emergency switch for lowering the stretcher
If you had to fold the stretcher in the manual
way, you will pull the emergency lever to fold it.
Belts with front locking push button
To unfasten the belts, push the red button. You
must always fasten the patient.
Automatic integrated charging system
When you keep the stretcher on the support, the
batteries of the stretcher will start to charge.
10 11 12

USER GUIDE // STRETCHER PC-750 + SUPPORT PB-720
Review 01/16
20
03 OPERATION
03.7 Loading and unloading operation
Starting from the position in which the support has been left after the loading of the
stretcher into the ambulance (1):
UNLOADING
· Pull the lever of the anchor point towards the left (A).
· Automatically the stretcher will be free. Push it out the ambulance (B) until the su-
pport are totally extract (2).
· Use the control panel to power the stretcher. WAIT 2 SECONDS to activate the system
and later push the UP button (C).
· Once the stretcher will be in its highest position, which will be free (4).
· Move away the stretcher in straight line until being completely out of the support.
· Again, pick the support up into the ambulance by the lever placed on right side (C).
LOADING
· Pull the support out the ambulance by lever of the anchor point (A).
· Push the support by lateral handles until its maximum.
· Move the stretcher closer towards the support in straight line (5) make sure the whe-
els are placed like the image (D).
· Push the DOWN button on the control panel of the stretcher (E) and after push right
lateral lever of the support (C) to put the set into the ambulance.
· Secure the stretcher is fasten on the anchor point (A) and anchor point is on close
position.
· Verify the stretcher are charging, pushing the POWER button.
A
C
3
2
1
4
5
B
D
C
UP
E
DOWN
THE FRONT WHEELS OF THE STRETCHER
MUST BE LOCKED WHEN THE LOADING/
UNLOADING OPERATION ARE EXECUTED.
ON THE CONTRARY, IT IS POSSIBLE IM-
PORTANT ELEMENTS OF THE STRETCHER
COULD BE DAMAGED.