Promeba PC-218 User manual

USER GUIDE
STRETCHER // PC-218
Review 12/18

USER MANUAL // STRETCHER PC-218
Review 12/18
3
01 INTRODUCTION
01.1 Using this manual
01.2 Technical data sheet
02 INSTALATION
02.1 Transporting and unpacking
03 OPERATING
03.1 Elements
03.2 Commands
03.3 Loading and unloading operation
03.4 Pushrod
04 MOUNTING AND COMPONENTS
04.1 General view STRETCHER PC-218
04.2 Set stretcher PC-218
04.3 Bunk set PC-218
04.4 Set guide rods PC-218
04.5 Telescopic hand grips PC-218
04.6 Standard rotating leg set with brake PC-218
04.7 Inverted rotating leg set with brake PC-218
05 GENERAL MAINTENANCE
06 LEGAL NOTICES
07 PRODUCT WARRANTY
INDEX
MODEL PC-218
STANDARD CONFIGURATION

USER MANUAL // STRETCHER PC-218
Review 12/18
5
01 INTRODUCTION
01.1 Using this manual
This manual provides using and maintenance instruc-
tions of the product, as well as the way of xing minor
faults that could appear.
It is recommended before the operation of the product
to read carefully this manual in order to avoid damages
caused by a misuse.
Do not lose this document, it should be accessible to
any doubt that could appear by medical personnel.
Remember that a good use and maintenance are ne-
cessary for the proper operation of the product.
Each product incorporates an identication sticker with
the serial number and the model. Keep these numbers
so that they can be indicated to the dealer if necessary.

USER MANUAL // STRETCHER PC-218
Review 12/18
7
01 INTRODUCTION
01.2 Technical data sheet
MEASURES AND FEATURES // PC-218
LENGHT 1920 mm INTERMEDIATE STOP 500-580 mm
WIDTH 580 mm FOLDED HEIGHT 300-330 mm
HEIGHT 800-880 mm MAX. LOAD 250 Kg
WEIGHT 40 Kg
880
580
800
330
300
1920

USER MANUAL // STRETCHER PC-218
Review 12/18
9
02 INSTALATION
02.1 Transporting and unpacking
First remove the packaging carefully to prevent dama-
ge to the exterior of the stretcher.
1. Transporting
· Always x the load, if piling up is necessary always
follow the scheme shown.
· Transport the leveled load and following all precepts
and rules for the transport of loads.
2. Unpacking
· Place the box on a at, stable surface and open the
seal being careful not to damage the inside.
· Remove the stretcher from the inside of the load as
shown in the scheme below.
Each stretcher has been minutely examined when lea-
ving the factory. To ensure that it has not been dete-
riorated during transport, please carefully inspect the
outside and the inside, and in case of nding any im-
perfection, immediately contact the installer.
For an optimum operation, the stretcher must be leve-
led.
PACKING UNIT
RRESPECT THE PACKING’S TRANSPORT POSITION
PRODUCT’S UNPACKING
ALWAYS USE A FLAT BASE SUPPORT

USER MANUAL // STRETCHER PC-218
Review 12/18
10
03 OPERATING
03.1 Elements PC-218
1. Wheels for vertical movement
2. Rear leg operating lever
3. Front leg operating lever
4. Third anchor point
5. Front rotating leg brake
6. Rear rotating leg brake
7. Front leg holding position operating lever
8. Telescopic handles
2
3
4
5
1
6
7
8

USER MANUAL // STRETCHER PC-218
Review 12/18
11
03.1 Elements PC-218
03 OPERATING
9 6 8

USER MANUAL // STRETCHER PC-218
Review 12/18
12
03 OPERATING
03.2 Commands PC-218
01. REAR LEGS UNLOCKING LEVER
Green, located on the stretcher’s left side. The legs of the
rear side will unlock by operating the lever in order to place
the stretcher in loading and unloading position.
02. FRONT LEGS UNLOCKING LEVER
Red, located on the stretcher’s right side. The legs of the
front side will unlock by operating it in order to place the
stretcher in loading and unloading position.
03. HOLDING POSITION LEVER
Red, located on the front right side. It allows a second posi-
tion which facilitates the loading of the patient.
01 02 03
01
02
03

USER MANUAL // STRETCHER PC-218
Review 12/18
13
03 OPERATING
03.3 Loading and unloading operation
LOADING
· Open the loading ramp of the bench/rail (A)
· Place the stretcher head-on in relation to the loading axle of the bench (A)
· Approach the stretcher until the front wheels have contact with the loading ramp (B)
· Operate the right lever (RED) to unlock the front wheels (C)
· Decisively push to slide the stretcher into the ambulance (D)
· As the rear leg approaches, press the left lever (GREEN) to release the legs (E)
· Keep pushing until the stretcher is fully loaded (E)
· Pay attention to the third anchor point, you may heard a CLICK (in case of being installed)
· Close the loading ramp
UNLOADING
· Open the loading ramp of the bench/rail
· Release the stretcher’s closure by operating the lever (in case of being installed)
· Pull the stretcher. It will slide outward, hold it with the hands
· Plegar la rampa de carga
A B
C D
E F

USER MANUAL // STRETCHER PC-218
Review 12/18
15
03 OPERATING
1
2
3
03.4 Pushrod PC-218
To adjust the tension of the drive cables, the stretcher has
three pushrod systems for its regulation:
1. HANDLE UNLOCKING BACK LEGS
2. HANDLE UNLOCKING FRONT LEGS
3. INTERMEDIATE STOP SHAFT

Standard rotating leg set with brake PC-218
Pág. 26

USER MANUAL // STRETCHER PC-218
Review 12/18
17
04.1 General view STRETCHER PC-218
04 MOUNTING AND COMPONENTS
3Bunk set PC-218
Pág. 20
2Set stretcher PC-218
Pág. 18
5Telescopic hand grips PC-218
Pág. 24
4Set guide rods PC-218
Pág. 22
Inverted rotating leg set with brake PC-218
Pág. 28
7
Standard rotating leg set with brake PC-218
Pág. 26
6

USER MANUAL // STRETCHER PC-218
Review 12/18
18
04.2 Set stretcher PC-218
04 MOUNTING AND COMPONENTS
28
2
2
2
2
5
32
11
35
36
30
29
14
16
24
34
10
52
38
6
7
3
20
33
34

USER MANUAL // STRETCHER PC-218
Review 12/18
19
04.2 Bill of materials SET STRETCHER PC-218
NUM. ELEMENT CODE - DESCRIPTION UNITS
1.01 PC2180-00012 - PERFIL SUPERIOR CAMILLA FUNERAL 2
1.02 PC6500-03460 - SUBCONJUNT MANETES EXTENSIBLES 4
1.03 PC6170-03092 - SUBCONJUNT TRAVESSER DAVANTER 1
1.04 PC6182-01042 - SUBCONJUNT TIRANT POTES
DAVANTERES
1
1.05 PC6180-01000 - CONJUNT GUIA VARILLES CAMILLA 1
1.06 PC6500-03070 AMORTITZER 220MM-70N 1
1.07 VASTEG PISTÓ STABILUS 7873FA 1
1.08 PC6500-03080 - AMORTITZER 320MM-70N 1
1.09 VASTEG PISTÓ STABILUS 6008YF 1
1.10 PC6100-03151 - TORRIO ENGANCHE 1
1.11 PC6170-01031 - CASQUELL POTES 4
1.12 PC6500-03050 - BRIDA PATÍ 2
1.13 PC6500-03060 - COIXINET GIR PATI 2
1.14 CD-RUEDA-100 - RODA 100x24 2
1.15 PC6180-00042 - PATI DAVANTER DRET CAMILLA 1
1.16 PC6170-03460 - TOPE LATERAL CAMILLA 2
1.17 PC6180-00052 - PATI DAVANTER ESQUERRA CAMILLA 1
1.18 PC6180-00062 - TUB TOPE POTA DAVANTERA 2
1.19 PC6180-02072 - SUBCONJUNT TIRANT POTES
POSTERIORS ESTRET
1
1.20 PC6270-03012 - CONJUNT SUPORT POTA POSTERIOR
ESTRETA
1
1.21 PC6180-00070 - BANDA PROTECTORA CAMILLA 2
1.22 PC6180-00080 - TERMINAL PERFIL ESQUERRA 2
1.23 PC6180-00090 - TERMINAL PERFIL DRET 2
1.24 PC6170-03330 - MANETA DESPLAÇADA ESQUERRA
INJECCIÓ
1
1.25 PC6270-03072 - SUFRIDERA SUPORT POTA 2
1.26 PC2180-00030 - FEMELLA SUBJECCIO PERFIL CAMILLA
FUNERAL PC-218
2
1.27 PC6180-00081 - CASQUELL 10x10x2mm CINCADO 1
1.28 PC2180-01000 - CONJUNT LLITERA CAMILLA FUNERAL 1
1.29 PC2180-00022 - SUPORT RODES LLITERA CAMILLA
FUNERAL
4
1.30 PC2180-00040 - TOPE NYLON RODA CAMILLA FUNERAL 4
1.31 PC6580-03002 - TOPE POTA POSTERIOR PC-658 2
1.32 PC2182-03000 - CONJUNT POTA INVERTIDA GIRATORIA
BLOQUEJABLE AMB FRE FUNERAL
1
04 MOUNTING AND COMPONENTS