Prominence Home Almadale 50330 User manual

9245 • 040517
56” CEILING FAN
Owner’s Manual
Model #50330
1
If a problem cannot be remedied or you are experiencing diculty in installation,
please contact the Service Department: 1-877-706-3267, 9 a.m.- 5 p.m. Central time.

PACKAGE CONTENTS
2
HARDWARE CONTENTS
13
14
15
16
17
1. Mounting Bracket
2. Downrod
3. Canopy
4. Canopy Cover
5. Yoke Cover
6. Motor Assembly
7. Switch Housing
8. Optional Light Kit
Housing
9. Pull Chain Extension
10. Blades (x 3)
11. Hardware Kit
12. Owner’s Manual
13. Motor Screw (x 6)
14. Mounting Bracket
Screw (x 4)
15. Downrod Set Screw (x 2)
16. Wire Connector (x 3)
17. Switch Housing Screw (x 3)
Unpack your fan and check the contents. You should
have the following items:
PACKAGE CONTENTS
HARDWARE CONTENTS
Note: Some extra hardware has been included. The quantity
listed above is the number required for installation.
1
2
3
4
5
6
7
8
9
10
11
12

MOUNTING OPTIONS
3
A. 13.75 in. B. 5.19 in. C. 2.40 in.
DIMENSION REFERENCE
B
C
A
Choose one of the following mounting options:
Downrod Mount is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer
downrod (not included).
Angled Ceiling Mount is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to
ensure proper blade clearance from the ceiling. If using the angle mount, check to ensure the ceiling angle is not
steeper than 16°.
Dual Mounting Options
Downrod Mount
Slope Ceiling Mount (Up to 16 degrees)

WARNING
READ ALL SAFETY INFORMATION AND INSTALLATION INSTRUCTIONS BEFORE YOU BEGIN INSTALLING THE
FAN AND SAVE INSTRUCTIONS.
All set screws of the fan must be checked and retightened where necessary before installation.
To reduce the risk of personal injury, do not bend the blade brackets when installing the brackets, balancing
the blades or cleaning fan. Do not insert foreign objects in between rotating fan blades.
Before changing the fan direction, turn o the fan and wait for the fan blades to stop completely.
If a stationary appliance is not provided with a supply cord and a plug, or with other means for
disconnection from the main supply having a contact separation of at least 3 mm in all poles, that means for
disconnection must be incorporated in the xed wiring in accordance with the wiring rules.
NOTE: The safeguards provided by these safety instructions and by the separate installation instructions
are not meant to cover all possible conditions and situations that may occur. It must be understood that
common sense, caution and care are factors which can not be built into this product. These factors must be
supplied by the person(s) installing, caring for and operating the fan.
TO AVOID RISK OF ELECTRIC SHOCK, BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE. TURNING OFF THE ELECTRICAL POWER
BY USING THE LIGHT SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRICAL SHOCK.
TO REDUCE THE RISK OF INJURY, INSTALL THE FAN SO THAT THE BLADES ARE AT LEAST 7 FEET (2.1
METERS) ABOVE THE FLOOR AND AT LEAST 18 INCHES (0.5 METERS) FROM THE TIP OF THE BLADES TO
THE WALL.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX
MARKED “ACCEPTABLE FOR FAN SUPPORT” AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET
BOX.
THE INSTALLATION HAS TO BE IN ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE, ANSI/NFPA
70-1999 AND LOCAL CODES. IF YOU ARE UNFAMILIAR WITH THE METHODS OF INSTALLING ELECTRICAL
WIRING, SEEK THE SERVICES OF A QUALIFIED LICENSED ELECTRICIAN.
SAFETY INSTRUCTIONS
4
IMPORTANT:
Before you begin installing or using the fan, carefully read the entire manual. If unsure about any part of the
installation, contact a qualied electrician.
Save all instructions.
NOTE: The fan weight is net weight: 13.34 lb (6,35 kg). Be sure the outlet box (not included) is securely attached
to the building structure and is marked “Acceptable For Fan Support”. Failure to do so can result in serious injury.

8 in.
5
ASSEMBLY INSTRUCTIONS
1
1. Turn OFF the electrical power at the main fuse or circuit
breaker.
4
3
Motor Screw
3. Remove the six motor screws from the top of the motor
assembly and save for blade installation.
4. Depending on the length of the downrod you choose,
you may want to cut the lead wires back to simplify wiring.
If you decide to cut back the lead wires, do so in the
following manner: Pull the lead wires completely through
the top of the downrod on the motor assembly. Measure 8
inches of lead wire and cut o the excess with wire cutters.
Then, strip 1/2 inch of insulation from the end of each wire
and twist the ends.
2
2. Install the mounting bracket to the outlet box (not
included) using the screws and washers provided with the
outlet box.
Warning: To reduce the risk of re electric shock,
or personal injury, mount to the outlet box marked
“acceptable for fan support” and use the mounting screws
and washers provided with the outlet box.

6
ASSEMBLY INSTRUCTIONS
Tab
Slot
Downrod
Mounting
Bracket
Black (Hot)
Wire Connector
White (Neutral)
Bare/Green (Ground)
Black Blue White Green
Mounting
Bracket
Screw
L-shaped Slot
Round Hole
Mounting
Bracket
7
5
6
5. Install the ball end of the downrod into opening in the
mounting bracket. Align one of the slots in the downrod
with the tab in the mounting bracket. The downrod
should not rotate in the mounting bracket if installed
properly.
DANGER: Failure to align the slot in the ball with tab may
cause the fan to fall, resulting in serious injury or death.
6. Connect household supply and fan wires according to
the diagram and these steps:
• Connect the Green wire from the downrod and mounting
bracket to the Bare/Green supply wire.
• Connect the White wire from the fan to the White supply
wire.
• Connect the Black and Blue wires from the fan to the
Black supply wire.
• Secure all wiring connections together with wire
connectors.
Note: If a second hot power wire is available from the
outlet box, connect it to the blue (light power) fan wire for
separate fan and light switches.
Important: After the connections have been made, the
wires should be turned upward and pushed carefully
up into the outlet box. Place the black and white wire
connections on opposite sides of the outlet box.
8. Align the two holes of the blade assembly over two
holes on the motor assembly. Insert two of the previously
removed motor screws through the holes in the blade
assembly and tighten the motor screws securely. Repeat
with the other two blade assemblies, making sure to
completely secure each blade assembly before moving to
the next.
To install an optional light kit with this fan, proceed to
page 8.
7. Raise the canopy, ensuring that the two mounting
bracket screws are aligned with the L-shaped slots in
the canopy. Then turn the canopy clockwise until the
mounting bracket screws are completely engaged in
the L-shaped slots. Install the two previously removed
mounting bracket screws and star washers in the round
holes. Securely tighten all mounting bracket screws.
8
Motor
Screw

7
ASSEMBLY INSTRUCTIONS
OPERATING INSTRUCTIONS
1
1. The pull chain has four positions to control the fan
speed. One pull is HIGH, two is MEDIUM, three is LOW and
four turns OFF the fan.
9. Attach the pull chain extension to the pull chain.
9
Pull Chain
Extension
10
17. Restore the power at the main fuse or circuit breaker.

8
I
2
OPTIONAL LIGHT KIT INSTRUCTIONS
1. To install the fan with an optional light kit, remove
the three tter plate screws from the sides of the switch
housing and set aside for later.
2. Remove the pull chain assembly by twisting the pull
chain ferrule counter clockwise. Remove the reverse
switch by removing the two small screws holding it in
place.
3. Connect the pull chain ferrule and the reverse switch to
the optional light kit housing.
4. Attach the light kit (sold separately) to the optional
light kit housing according to the manufuacturer’s
instructions. Then, reinstall the tter plate screws to secure
the optional light kit housing to the tter plate.
1
Fitter
Plate
Screws
Pull
Chain
Ferrule
Pull
Chain
Ferrule
Fitter Plate
Screw
Reverse
Switch
Screws
Reverse
Switch
Screws
3
4

9
If you have diculty operating your new ceiling fan, it may be the result of incorrect assembly, installation or
wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please
check the Troubleshooting section below. If a problem cannot be remedied or you are experiencing diculty in
installation, please contact customer service: 1-877-706-3267, 9 a.m.- 5 p.m. Central time.
PROBLEM SUGGESTED REMEDY
1. Fan does not start 1. Check main and branch circuit fuses or circuit breakers.
2. Check power supply wire connections to fan and switch wire connections in
switch housing.
CAUTION: Make sure main power is turned o.
3. Make sure the reverse switch pushed completely left or right. Fan will not
operate when switch is in the middle.
4. Make sure that the wall control is turned ON.
1. Make sure all screws in motor housing are snug, but not overtightened.
2. Make sure the screws which attach the blade arm to the motor are tight.
3. Make sure wire connectors in switch housing are not rattling against each other
or against the interior wall of the switch housing.
CAUTION: Make sure main power is turned o before entering switch housing.
4. If using a light kit, be sure the glass shades are nger tight. Check to be sure light
bulb are snug in sockets and not touching glass shade(s). If vibration persists
from glass, remove glass and install a 1/4 in. wide rubber band on glass neck to
act as an insulator. Replace glass and tighten screws against rubber band.
5. Some fan motors are sensitive to signals from Solid State variable speed controls.
DO NOT USE a Solid State variable speed control.
1. Ensure all blades are screwed rmly into blade arms.
2. Ensure all blade arms are tightened securely to motor.
3. Ensure canopy and mounting bracket are tightened securely to outlet box and
outlet box is mounted rmly to ceiling joist.
4. Switch one blade with a blade from the opposite side. Or balance the fan using a
balancing kit.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
1. Make sure the reverse switch is in the left position.
2. Change to higher fan speed by pulling the fan pull chain.
2. Fan is noisy
3. Fan wobbles
5. Weak airow:
TROUBLESHOOTING

LIMITED LIFETIME WARRANTY
To obtain Service, please contact the Service Department:
1-877-706-3267, 9 a.m.- 5 p.m. central time.
Model Name: 56” Ceiling Fan
Model No: 50330 - Brushed Nickel
10
Subject to the limitations set forth below, Hong Kong China Electric appliance Company (HKC)
warrants the fan motor for this ceiling fan to be free from defects in workmanship and material
for the life of the product. Also, subject to the limitations below, HKC warrants all ceiling fan parts
(“ceiling fan parts” excludes the motor and parts made in whole or in part with glass) to be free
from defects in workmanship and material for a period of one year after the date of purchase by the
original purchaser at retail.
All claims must be made by the original purchaser, whether such purchaser purchased the product
through a store or contractor. Ceiling fan part defects must be reported within the rst year from
the date of purchase. Parts made in whole or in part with glass and the nishes of metal and other
surfaces are not warranted.
Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any
part caused by ordinary wear and tear, accident, misuse, or improper installation, is not covered by
this warranty. HKC assumes no responsibility whatsoever for fan installation. Any service performed
by a non-licensed electrician will render the warranty invalid.
HKC’s sole responsibility shall be to repair or replace the motor, parts, or product within the terms
stated above. HKC shall not be liable for any loss or damage of any kind, including any incidental
or consequential damages resulting directly or indirectly, from any breach of warranty, express or
implied, or any other failure of this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages so this limitation may not apply to you.
If the original purchaser ceases to own the fan, this warranty is voided.
Should the purchaser encounter a problem with your fan related to defects in workmanship or
materials within the warranty period associated with the defective part, HKC agrees to replace
the defective part without charge, or at its option, to replace the ceiling fan with a comparable or
superior model.
HKC’s warranties are limited to the written warranties set out in this HKC ceiling fan limited lifetime
warranty. All other express and implied warranties, including, without limitation, the implied warranty
of tness for a particular purpose and the implied warranty of merchantability are disclaimed. Some
states do not allow the disclaimer of implied warranties, so this disclaimer may not apply to you.
To obtain warranty service, please write down your model number and call Customer Service
at 1-877-706-3267. Please have a copy of the receipt as proof of purchase.