Proteco ASTER NEW User manual

AUTOMATION FOR SWING GATES
Installation Manual
ASTER NEW

INDEX
4
1. WARNINGS
2. DESCRIPTION AND INTENDED USE 5
2.1 Content 5
2.2 Technical features 5
2.3 Dimensions 5
2.4 Life line 6
3. INSTALLATION 6
3.1 Introduction 6
3.2 Preliminary checks 6
3.3 Electric layout 7
3.4 Installing the operator 7
8
8
9
9
3.4.1 Quotes from ground
3.4.2 Pillar quotes
3.4.3 Outward opening
3.4.4 Fixing the pillar bracket
3.4.5 Fixing the gate bracket
3.4.6 Wirings
10
11
4. MAINTENANCE
5. END USER GUIDELINES 12
5.1 Safety tip 12
5.2 Manual opera 12
5.3 Maintenance 13
5.4 Warranty 14
5.5 Disposal 14
5.5.1 Disposal of the syste 14

Connect the automation to the earth system, which must be efficient and properly carried out.
The installation of automatic doors and gates must comply with the Machine Directive 2006/42/CE, in particular EN
12453 and performed by qualified personnel only.
Make sure the main power line is equipped with state of the art safety grounding system; as well be sure the
whole installation is protected by a power cut switch and against overcurrent.
Make sure the area is clear from flammable gases and/or electromagnetic interferences: it could lead to very
dangerous injuries.
Switch the power and batteries OFF before any operation.
After installation, packaging and waste materials (cardboard, plastic, metal parts etc.) must be kept away from
children as they could be potentially harmfull.
Use only original spare parts. Any alteration to the system is prohibited.
Proteco Srl will not respond in case of using additional and/or fake spares.
Before commissioning the system, deliver the last pages of this manual to the user (section 5. END USER’S TIPS ).
Proteco S.r.l. reserves the right to make changes to the product without notice.
4
ASTER - rev. 13_02_2021
1. WARNINGS
This manual contains important information concerning personal safety.
An incorrect installation or an improper use may lead to severe injuries.
Read carefully and store for future use. Pay particular attention to this symbol .

2. DESCRIPTION AND INTENDED USE.
The ASTER operator is designed to automate swing gates.
The use of this product for purposes other than those described and installation executed in a manner other than as instructed
in this technical manual are prohibited.
All ASTER systems are locked, therefore no electric-lock is needed.
In case of power cut the gate operator can be easily released by manual operation. (See 5.2. Manual operation).
2.1 Content
DESCRIPTION CODE UNITS
1ASTER NEW - RH operator PAN....A0D 1
2ASTER NEW - LH operator PAN....A0S 1
3FITTINGS BAG
(For TI version - double gate) SSAB12 1
4CAPACITOR ............. 2
5RELEASE KEY SCH0190 2
2.2 Technical features
ASTER 3 ASTER 4 ASTER 5 ASTER 6
Power supply 24Vdc 230V-50Hz 115V-60Hz 24Vdc 230V-50Hz 115V-60Hz 24Vdc 230V-50Hz 115V-60Hz 230V-50Hz
Max. motor voltage 0,75A 1,7A 2,3A 0,75A 1,7A2,3A 0,75A 1,7A 2,3A 1,7A
Rated power 50W 280W 300W 50W 280W 300W 50W 280W 300W 280W
Capacitor --- 8µf 30µf --- 8µf 30µf --- 8µf 30µf 8µf
Thermal cut off --- 150°C 150°C --- 150°C 150°C --- 150°C 150°C 150°C
Rated thrust 2500N 2800N 3000N 2500N 2800N 3000N 2500N 2800N 3000N 2800N
IP rating 44 44 44 44 44 44 44 44 44 44
Revolutions 1600 rpm 1400 rpm 1700 rpm 1600 rpm 1400 rpm 1700 rpm 1600 rpm 1400 rpm 1700 rpm 1400 rpm
Max. opening angle 100° 100° 100° 110° 110° 110° 110° 110° 110° 120°
Opening time - 90° opening 15’’ 17’’ 14’’ 20’’ 22’’ 18’ 25’’ 27’’ 22’’ 32’’
Max. leaf weight 275Kg 350Kg 300Kg 250Kg 350Kg 300Kg 150Kg 250Kg 200Kg 250Kg
Max. leaf length 2,00m 2,00m 2,00m 2,50m 2,75m 2,75m 3,00m 3,50m 3,50m 4,00m
Duty cycle 80% 40% 40% 80% 40% 40% 80% 40% 40% 40%
2.3 Dimensions
ASTER 3 = 620 ASTER 4 = 720
ASTER 5 = 820 ASTER 6 = 920
ASTER 3 = 940 ASTER 4 = 1140
ASTER 5 = 1340 ASTER 6 = 1540
5
ASTER - rev. 13_02_2021
1
2
3
4
5
159 mm172 mm
117 55 104 55
53 97
Motor 24V
Motor 230/115V 64

2.4 Life line
The life of the gearmotor may be affected by multiple waste factors.
The life expectation can be calculated using the criteria outlined in
the below table.
In order to get the waste rate add together all values that comply
with the installation scenario and according to the accessories
fitted.
ATTENTION:
If the waste rate obtained is beyond 10, move to a superior
version in order to fulfill the expected performances.
ASTER 3
NEW
ASTER 4
NEW
ASTER 5
NEW
ASTER 6
NEW
Max. width 1,5 m 1 1 0,5 0,5
Max. width 2 m 1,5 1 1 0,5
Max. width 2,5 m 2,5 1,5 1 1
Max. width 3 m 3 2,5 1,5 1
Max. width 4 m 3,5 3 2,5 2
Max. weigth 200 Kg 1,5 1 1 0,5
Max. weigth 250 Kg 2 1,5 1,5 0,5
Max. weigth 300 Kg 2,5 2,5 2 1
Max. weigth 350 Kg 3 3 2,5 1,5
Windy areas 3 3 3 3
Paneled leaf 1,5 1,5 1,5 1,5
Outside temperatures often
beyond 40° or below 0°
1 1 1 1
Follow the waste rate line of the graph to get the estimated duty
cycles.
Duty cycles obtained may be compromised if the maintenance plan
is not carefully respected.
Duty cycles are determined on the base of design analysis,
project calculations and tests carried out at factory (gates
opening at 90°).
Therefore duty cycles achieved as well as the waste rate are a
mere estimation.
ATTENTION!
Any other use other than that described and in environmental
conditions other than those indicated in this manual is to be
considered improper and prohibited.
For a proper installation, strictly follow the following procedure,
respecting the below chronological order:
3.2 Preliminary checks
Before proceeding to installation, it is necessary to double check
the good condition of every component and make sure the site is
suitable for installation purposes.
- All components must be integral and suitable to use.
- Make sure the area around the system is clear enough to allow
eazy and safe manual operation.
- Make sure weight, dimensions and gate features are suitable to
the model you have choosen.
- Make sure the gate area is fitted with ground stops both in
opening and closing.
- Make sure the gate is mechanically free of friction.
- Make sure the automation fixing area is compatible with the
dimensions of the brackets and that there is sufficient space to
carry out manual operation easily and safely.
- Make sure the automation positioning area is not subject to
flooding.
- Make sure the electric circuit is connected to a state of the art
safety grounding.
- Make sure the fixing surfaces of the photocells are flat and
allow correct alignment between transmitter and receiver.
6
ASTER - rev. 13_02_2021
WASTE RATE
CYCLES
3. INSTALLATION
3.1 Introduction
ATTENTION!
Matrix must be installed by qualified personnel only,
complying with law regulations and instructions
contained in this manual.
7

3.3 Electric layout
Motor 230V/115V Motor 24V
AOperator 3 x 1,5 mm² + Terra 2 x 1,5 mm²
BControl unit 2 x 1,5 mm² + Terra 2 x 1,5 mm² + Terra
CRX photocell 4 x 0,5 mm² 4 x 0,5 mm²
C¹ TX photocell 2 x 0,5 mm² 2 x 0,5 mm²
DKey switch 2 x 0,5 mm² 2 x 0,5 mm²
EAntenna RG58 RG58
FBlinker 2 x 0,5 mm² 2 x 0,5 mm²
GRadio receiver 2 x 0,5 mm² 2 x 0,5 mm²
NB: Cables necessary for the installation of the system (not included)
may vary according to the quantity and type of accessories and
devices fitted.
7
ASTER - rev. 13_02_2021
•Switch the POWER OFF before starting any wiring.
•Fit a power cut switch to protect the electric plant against
overcurrent.
The standard requires a separation of contacts of at least 3
mm in each pole(EN 60335-1).
•The installation requires skills in the electrical and mechanical
fields; it must only be performed by qualified personnel able to
release the declaration of conformity (type A) on the whole
installation (Machine Directive 2006/42/CEE, attachment IIA).
•The main electric plant shall comply with the oustanding
regulation and shall be state of the art carried out.
•The power supply lines to the motors, control unit and
accessories must be separated in order to avoid possible
interferences that could generate system malfunctions.
•The electric cable coming out of the actuator must not be
stretched but make a wide downward curve to avoid the
backflow of water inside the actuator itself (see the picture
above).
3.4 Installing the operator
Check the orientation of the motors, left or right hand, referring to
picture A. If hinges are positioned on the right (property view), the
motor will be right hand, and viceversa.
Make sure the gate is fitted with ground stops both in opening
and closing (picture B).
Picture A

ASTER 3: A=150 B=150
ASTER 4: A=200 B=200
ASTER 5: A=250 B=250
ASTER 6: A=300 B=300
Required height
400 mm min.
30 mm
ASTER 3: D= max 125 mm
ASTER 4: D= max 175 mm
ASTER 5: D= max 225 mm
ASTER 6: D= max 275 mm
Picture D
ASTER 6 NEW (90°)
D275 250 225 200 175 150 125 100 75
A210 240 280 275 300 300 330 370 410
B335 330 305 310 285 290 265 240 215
Bracket 80 80 80 110 110 140 140 140 140
Minimum leaf
length
1320 1300 1280 1280 1260 1270 1240 1220 1200
ASTER 5 NEW (90°)
D225 200 175 150 125 100 75 50 25
A165 190 200 200 200 200 250 300 345
B305 280 255 260 265 240 215 190 165
Bracket 80 80 80 110 140 140 140 140 140
1150 1130 1130 1130 1140 1120 1100 1070 1050
ASTER 3 NEW (90°)
D125 100 75 50 25 0
A110 150 145 140 135 160
B205 150 155 160 165 140
Bracket 80 50 80 110 140 140
860 840 840 850 850 830
ASTER 6 NEW (110°)
D150 125 100 75
A250 260 280 275
B260 235 210 215
Distance between
hinge and pillar 80 70 60 50
Bracket 110 110 110 140
1300 1280 1250 1260
ASTER 4 NEW (90°)
D175 150 125 100 75 50 25 0
A115 140 165 160 155 180 210 240
B255 230 205 210 215 190 165 140
Bracket 80 80 80 110 140 140 140 140
1000 980 980 970 970 970 950 930
30 mm
NB: for an opening angle of 90° the
minimum recommended distance between
the hinge and the pillar is 30 mm.
ASTER 6 NEW (120°)
D125 100 75
A290 285 185
B175 180 280
100 90 70
Bracket 50 80 110
1250 1260 1260
ASTER 5 NEW (110°)
D100 75 50 25
A220 220 215 235
B210 185 190 165
70 60 50 40
80 110 140 140
1100 1100 1200 1200
8
ASTER - rev. 13_02_2021
3.4.1
Brackets must be positioned at a minimum height of (picture B).
If the gate is particularly light, fit the operator as closer as possible
to gate centerline.
Picture B
3.4.2
The ideal approach is to fix the brackets complying with the
measures A and B as indicated in the below table for an opening
angle of 90° (picture C/D).
If the ideal scenario of A and B is not applicable, then refer to the
below table to get some other possible combinations according
to the width of the pillar.
Values are expressed in mm. The Aster New can replace the
previous model ensuring the same excursions and the same
opening angles, without having to replace the existing ones.
Quotes from ground
Pillar quotes
Minimum leaf
length
Minimum leaf
length
Minimum leaf
length
Minimum leaf
length
Distance between
hinge and pillar
Minimum leaf
length
Bracket
Distance between
hinge and pillar
Minimum leaf
length

ASTER 4 NEW (110°)
D50 0
A175 175
B140 140
40 30
80 140
925 920
ASTER 3 NEW (110°)
D25 0
A165 140
B120 140
40 30
140 140
810 800
Operator ASTER 3 ASTER 4 ASTER 5 ASTER 6
A115 115 115 115
B220 200 200 200
Distance from pillar 5 5 5 5
bracket 140 140 140 140
Min. leaf length 800 1000 1200 1200
Cut line
Picture F
Picture I
Picture G
Picture L
RH cap = RH motor
LH cap = LH motor
NB: Be carefull when fitting the cap. It
has to match the proper motor.
Picture M
9
ASTER - rev. 13_02_2021
5 mm
5 mm
5 mm
30 mm
> 30
12 mm
3.4.4 Fixing the pillar bracket
3.4.3 Outward opening
It's possible to have your gate opening outward (picture E/F)
Picture E
Fixing the pillar bracket.
In order to properly cut the bracket start 12 mm from the hole
center, as shown in the picture.
Fix the motor to the bracket following the below procedure:
• Remove screw from plastic cap (picture L - A).
• Fit the bracket to the motor (picture I).
• Fit the pin (picture L).
•Put the cap back and screw (fig. M).
Bracket
Distance between
hinge and pillar
Minimum leaf
length
Bracket
Distance between
hinge and pillar
Minimum leaf
length

Picture N
3.4.6
115V-60Hz
230V-50Hz 24V dc CONTACT
1Yellow - Green EARTH
2Grey NEUTRAL
3Black Brown OPENING
4Brown BlueCLOSING
ATTENTION!
The electric plant must be protected by a ground system,
in accordance to the current safety regulations.
Do not let the motor wire stretch during opening and
closing.
Capacitors are provided just with 230V and 115V motors.
Picture O
Picture P
Picture Q
Picture R
Picture S
10
ASTER - rev. 13_02_2021
2 cm
3.4.5 Fixing the gate bracket
Follow the below procedure to determine the bracket position on
the gate:
- Put the gate to CLOSING position.
- Unlock the operator (refer to section 5.2 Manual Operation).
- Extend the inox arm fully.
- Turn back the arm 2 cms. This avoids the motor to “leap forward”
(picture N).
- Press the plastic cap with little force, and gently slide it forward
(picture O).
- Insert the bracket in the motor and fit the pin (picture P).
- Mount the arm of the motor onto the gate. Ensure the arm is
perfectly straight. Check the manual opening of the leaf before
definitively fixing the bracket to make sure the gate can open fully
to your required angle.
- If the bracket position is the correct one, remove the pin (picture
R) and proceed to definitively fix it.
- Repeat steps shown in picture P and Q.
NB: Check the manual opening of the leaf before definitively fixing
the bracket to make sure the gate can open fully to your required
angle.
NB: If you wish to remove the pin, take the cap off, and push
using a screwdriver (Ø max 4,5 mm) until the pin is out.
Wirings
Attention!
An incorrect wiring could lead to failures and very
dangerous injuries. Therefore carefully follow the wiring
instructions contained in this manual.
Switch the power and batteries OFF before any wiring
operation.
The electric plant must be performed by qualified
personnel and must comply with the outstanding
regulations.

11
ASTER - rev. 13_02_2021
Release system test
Take note of each intervention performed and mark it in the section
END USER GUIDELINES, 5.3 Maintenance: maintenance services
and repairings shall be noted, and the owner of the system shall
keep them for future reference.
4. MAINTENANCE
ATTENTION!
Maintenance service must be carried out by qualified technical
personnel, in full compliance with the safety standards required by
the laws in force.
Maintenance has to be carried out every six months.
In order to proceed to maintenance service, follow the below
checks:
• Turn the POWER OFF.
• Check the good condition of any component.
• Check screw connections are properly tightened.
•Unlock the operator, and make sure the gate opens and closes
freely. Clean the inox arm using a dry cloth (no lubrication
needed).
• Put the gate to closing position, lock the operator and if
necessary repeat the programming procedure.
• In order to check the good operation of the release system put
the gate to closing position and unlock to motor.
The unlock operation has to be smooth and eazy.
• The gate has to move freely in both directions.
• The release key has to turn smoothly and eazily.

Picture T
Picture U
Picture V
Picture Z
12
ASTER - rev. 13_02_2021
5. END USER GUIDELINES
Dear Customer, the following pages contain important information
for your safety and for complying with standing safety regulations.
Keep this manual for future reference.
5.1 Safety tips
Keep the operator away from children.
Children and people with reduced physical,
sensory, mental or limited experience and / or
knowledge can use automation only if provided
with supervision or specific instructions
regarding the safe use of the system.
The ASTER operator is designed to
automate swing gates.
The use of this product for purposes other
than those described and installation
executed in a manner other than as instructed
in this technical manual are prohibited.
Stay away from internal parts of
the automation: It's dangerous and there
are no components that can be repaired or
replaced by unqualified personnel.
Remote controls or other command devices
can be used only when the automation is
clearly visible and no dangerous situations
are detected.
Do not allow children to play within the system
area.
5.2 Manual operation
• Switch the POWER OFF.
• Lift the plastic cap acting on the right side of the operator
(picture T).
• Plug the release key and turn it 180° counter clockwise as
shown in picture U.
• The operator is now unlocked, manually open and close the
gate.
• Put the gate to closing position, lock the operator turning the
release key 180° clockwise.
•Reposition the plastic cap as shown in pictures V/Z.
Put a little force on the cap to reach the correct position.
•Switch the POWER ON.

DATE NOTES INSTALLER SIGNATURE OWNER SIGNATURE
5.3 Maintenance
To keep the automation safety and in good operation over time,
it is advisable to schedule a periodic maintenance plan with the
installer, or at least report any anomalous behaviors that may
require inspection.
In case of malfunctions it is advisable to contact the installer
who carried out the whole installation, rather than others.
Periodic maintenance and repairs must be reported by the
installer and the owner must keep them safe and available for
future reference.
End user may only take care of photocells and automation
housing cleaning.
Use the below table to note any intervention on the installation.
13
ASTER - rev. 13_02_2021

5.4 Warranty
5.5 Disposal
5.5.1 Disposal of the system
14
ASTER - rev. 13_02_2021
Any part of the system, including devices such as remote controls,
must be disposed in compliance with current legislation, as they
may be harmfull for the environment.
Most of the materials used are similar to solid urban waste and
can be handled accordingly.
They can be recycled through separate collection and disposed in
authorized centers.
Other components (electronic boards, batteries, etc.) may instead
contain polluting substances.
They must therefore be removed and delivered to companies
authorized for their recovery and disposal.
Before proceeding, it is always advisable to check the specific
regulations in force.
Disposal of packing
Packaging components (cardboard, plastics, etc.) are sare similar
to solid urban waste and can be handled accordingly without any
difficulty, simply by carrying out separate collection for recycling.
Before proceeding, it is always advisable to check the specific
regulations in force.
DO NOT POLLUTE THE ENVINRONMENT!
PROTECO products are covered by a 3-year limited warranty
from the production date printed on the product.
During this period, Proteco Srl offers a guarantee in case of
malfunction due to construction, material or assembly faults.
Warranty terms are applicable just if the instructions and
maintenance included in this manual are fully respected and
carried out.
Warranty is void when fake spares are used and doesn't respond
for faults due to incorrect installation.
Installation and any maintenance works are responsibility of the
person installing the system.
In no case and in no way will Proteco Srl be liable to the end user
for damages, including any loss of profits, savings or other
accidental or indirect damages, resulting from the use or inability to
use PROTECO products.
Any return without authorization number will be rejected.
The shipment of the returned product and the related costs are the
end user/buyer charge.
All defective products must be returned together with the proof of
payment to:
PROTECO Srl Via Neive 77, 12050 Castagnito (CN) - Italia
Warranty is void when:
- The product has been treated / stored under abnormal conditions
of use and maintenance.
- The product has been repaired, modified or altered.
- The product has been subject to misuse, neglect, electrical
problems, improper package, accident, or natural events.
- The product was installed improperly.
- The product warranty label is illegible or is missing entirely.
- The malfunction is due to improper installation or to natural and/
or accidental causes (eg: falls, oxidation, overvoltage).