Qiagen TissueLyser II User manual

General
instructions
авіаів Do
not
use
spray
bottles
to
spray
cleaning
or
disinfectant
liquids
onto
surfaces of
the
TissueLyser
II.
Spray
bottles should be used
only
for
the
TissueLyser
Adapter
Sets
and
Grinding
Jar
Sets.
If
solvents
or
saline, acidic,
or
alkaline solutions
are
spilt
on
the
TissueLyser
II,
wipe
the
spilt liquid
away
immediately.
Follow
manufacturer's
safety
instructions
for
handling cleaning
agents.
Follow
manufacturer's
instructions
for
soaking
time
and
concentration
of
cleaning
agents:
exposure
for
longer
than the recommended
soaking
time
can
damage
the
TissueLyser
II,
TissueLyser
Adapter
Sets,
and
Grinding
Jar
Sets.
Toxic
fumes
Do
not
use
bleach
to
clean
or
disinfect
used labware. Bleach
in
contact
with
salts
from
the
buffers
used
can
produce
toxic
fumes.
WARNING
A
Damage
to
the
instrument
Do
not
use
bleach,
solvents,
or
reagents
containing
acids, alkalis,
or
abrasives
to
clean the
TissueLyser
II.
CAUTION
A
Damage
to
the
instrument
Avoid
spilling
water
or
chemicals
onto
the
TissueLyser
II.
Damage
caused
by
water
or
chemical
spillage
will
void
your
warranty.
CAUTION
A
Remove
the
TissueLyser
Adapter
Set
or
Grinding
Jar
Set
from
the
clamps
of
the
TissueLyser
II.
Switch
on
the
TissueLyser
II.
Set
the oscillation
frequency
to
30
Hz.
Press
the
"START"
key.
TissueLyser
II
User
Manual
05/2016
37

•
•
Raise the transparent hood. The drive motor should switch itself off, and "F04" should
арреаг іп the display.
Lower the transparent hood. The drive motor should поІ switch itself оп again .
Іf there is а defecl, conlact QIAGEN Т echnical Services to request гераіг of the instrument.
Тissuelyser Adapter Sets and Grinding Jar Sets may become worn, depending оп the frequency
of use and the samples disrupted. This may lead to damage to the clamps of the Tissuelyser 11.
Check the Tissuelyser Adapter Sets and Grinding Jar Sets regularly for wear and Іеаг, and
герІасе if necessary.
Tissuelyser 11 User Manual 05/2016

Troubleshooting Guide
Error codes displayed Ьу the Tissuelyser 11
"FOl" displayed
Drive motor of Tissuelyser 11
overloaded
"F02" displayed
Drive motor of Тissuelyser 11 not
starting
"FОЗ" displayed
Specified oscillation frequency
exceeded
"F04" displayed
Transparent hood not lowered
"F05" displayed
Keys held down fог too long
"F06" displayed
Speed sensor defective
"F07" displayed
Solenoid switch defective
Tissuelyser 11 User Manual 05/2016
Comments and suggestions
When the drive motor is overloaded, the Tissuelyser 11 switches itself off to allow
the drive motor to сооІ. А display on the Тissuelyser 11 alternates between "FOl"
and the remaining cooling time in minules (e.g., "03" indicates З minutes).
After the cooling time has elapsed, switch the TissueLyser 11 off and then оп
again Ьеfоге continuing to operate the instrument.
lf the drive motor does not slart after the "START" key has been pressed, contact
QIAGEN Technical Services Іо request instrument гераіг. The drive motor may
Ье blocked, ог the motor ог speed sensor may Ье defective.
lf the specified oscillation frequency is exceeded, the Tissuelyser 11 switches itself
off and "FОЗ" is displayed. Contact QIAGEN Technical Services !о request
instrument гераіг. The speed sensor may Ье defective.
То protect the operator, the drive motor of the Тissuelyser 11 will only start if the
transparent hood has been lowered. lf the "START" key is pressed while the
hood is raised, "F04" is displayed and the drive motor does по! slart. Іf the
hood is raised while the Tissuelyser 11 is in operation, the drive motor switches
itself off and "F04" is displayed. То cancel the "F04" display, press the "STOP"
key.
Іf one ог mоге keys оп the keypad аге pressed and held down fог mоге than
15 seconds, the drive motor of the Tissuelyser 11 switches itself off and "F05" is
displayed. This is а safety mechanism to prevent unwanted changes іп the
operation of the Тissuelyser II should оп object land оп the keypad. То cancel
the "F05" display, switch the Tissuelyser 11 off and then оп again.
lf one of the magnets сопІгоІІіпg the speed of the Tissuelyser 11 is missing ог
defective, the instrument switches ilself off and "F06" is displayed. Contact
QIAGEN Technical Services !о request instrument гераіг.
Іf there is а defect in the саЬІе fог the solenoid switch, which monitors the
raising of the transparent hood, the Тissuelyser 11 switches itself off and "F07" is
displayed. Contact QIAGEN Technical Services to request instrument героіг.

AppendixA
Technical data
QIAGEN reserves the right to change specifications at апу time.
Environmental conditions
Operating conditions
Power
Overvoltage
category
Air temperature
Relative humidity
РІасе of operation
Altitude
Pollution level
100-240 V АС, 50-60 Hz, 150 W
Mains supply voltage fluctuations аге not to exceed 10% of nominal
supply voltages
11
5-40
°
С (41-1 04
°
F} •
Maximum 80%
(for temperatures up to З 1
°
С; linearly decreasing down to а relative
humidity of 50% at 40
°
С)
For indoor use опІу
Up to 2000 m (6500 ft.)
2
Т ransportation conditions
Аіг temperature
Relative humidity
Storage conditions
Аіг temperature
Relative humidity
Mechanical data
Dimensions
-25
°
С to 60
°
С (-1 З
°
F to 140
°
F) іп manufacturer's package
Maximum of 75% (noncondensing)
5-40
°
С (41-104
°
F) in manufacturer' s package
Maximum of 85% (noncondensing}
Height: 266 mm (up to 524 mm with the hood raised)
Width: 371 mm
*The instrument can also Ье operated а! 4°С under noncondensing conditions.
Tissuelyser 11 User Manual 05/2016

Mass
Oscillation
frequency
Noise characteristic
values
Depth: 461 mm
Арргох. 26 kg (without Tissuelyser Adapter Set ог Grinding Jar Set
installed)
3-30 Hz
The поіsе characteristic values аге also influenced Ьу the properties of the
sample to Ье disrupted.
Sound power level Lwл = 71.4 dB(A)
Emission value related to workplace L
p
дeq = 61 dB(A)
Waste Electrical and Electronic Equipment (WEEE}
This section provides information about disposal of waste electrical апd еІесtгопіс equipment Ьу
users.
The crossed-out wheeled Ьіп symbol (see below) indicates that this product must поt Ье disposed
of with other waste; it must Ье taken to ап approved treatment facility ог to а designated
соІІесtіоп роіпt fог recycling, according to ІосаІ laws апd regulations.
The separate соІІесtіоп апd гесусІіпg of waste еІесtгопіс equipment at the time of disposal helps
to conserve natural resources апd ensures that the product is recycled іп а mаппег that protects
human health апd the environment.
-
Recycling сап Ье provided Ьу QIAGEN upon request at additional cost. Іп the European Uпіоп,
іп ассогdапсе with the specific WEEE recycling requirements апd where а replacement product is
Ьеіпg supplied Ьу QIAGEN, free гесусІіпg of its WEEE-marked еІесtгопіс equipment is provided.
Tissuelyser 11 User Manual 05/2016