RADWAG MA X2.IC.A Series User manual

X2
Synergy
MA X2.A Moisture Analyzer
MA X2.IC.A Moisture Analyzer
IMMU-21-12-02-19-EN
www.radwag.com
USER MANUAL

- 2 -
Congratulations and thank you for selecting RADWAG product.
You have purchased a device that has been designed and manufactured to give you years
of service.
Please read this user manual carefully, this shall guarantee reliable operation.
FEBRUARY 2019

- 3 -
CONTENTS
1. GENERAL INFORMATION ....................................................................... 7
2. BASIC SAFETY PRECAUTIONS................................................................ 9
2.1. Warning Symbols and Signals..................................................................9
2.1.1. Warning Descriptions ...............................................................................................................9
2.1.2. Warning Symbols .....................................................................................................................9
2.2. Precautions ...........................................................................................9
2.3. Intended Use....................................................................................... 11
2.4. Good Weighing Practice......................................................................... 11
2.5. Precautions ......................................................................................... 11
2.6. Warranty............................................................................................. 12
2.7. Supervision over Metrological Parameters ............................................... 12
2.8. Service Manual Significance................................................................... 12
2.9. Staff Competence................................................................................. 12
2.10.Protective Clothing ............................................................................... 13
3. TRANSPORT AND STORAGE............................................................. 13
3.1. Delivery Check..................................................................................... 13
3.2. Packaging............................................................................................ 13
4. UNPACKING AND INSTALLATION.................................................... 13
4.1. Place of Use......................................................................................... 13
4.2. Unpacking........................................................................................... 14
4.3. Levelling ............................................................................................. 14
4.4. Standard Delivery Components List ........................................................ 14
4.5. Maintenance Activities .......................................................................... 15
4.6. Connecting the Moisture Analyzer to the Mains ........................................ 16
4.7. Temperature Stabilization Time.............................................................. 17
4.8. Connecting Peripheral Equipment........................................................... 17
5. START-UP ....................................................................................... 18
6. OPERATION PANEL ......................................................................... 18
7. HOME SCREEN................................................................................. 19
7.1. Weighing Result Window ....................................................................... 19
7.2. Drying Process Window......................................................................... 20
8. OPERATING THE MENU ................................................................... 21
8.1. Menu Accessing.................................................................................... 21
8.2. Screen Scrolling................................................................................... 21
8.3. Soft Buttons List .................................................................................. 22
8.4. Running Software Functions .................................................................. 22
8.5. Return to Weighing............................................................................... 23
8.6. Buttons, Labels and Text Fields Configuration .......................................... 24
8.6.1. Quick Access Buttons ........................................................................................................... 26
8.6.2. Labels.................................................................................................................................... 28
8.6.3. Text Fields............................................................................................................................. 30
8.6.4. Bar Graphs............................................................................................................................ 32
9. WEIGHING...................................................................................... 33
9.1. Good Weighing Practice......................................................................... 33

- 4 -
9.2. Log In Operation.................................................................................. 33
9.3. Units................................................................................................... 34
9.4. Weighing Unit Selection ........................................................................ 34
9.5. Weighing Units Availability .................................................................... 35
9.6. Start Unit Selection .............................................................................. 35
9.7. Custom Units....................................................................................... 36
9.8. Zeroing............................................................................................... 36
9.9. Taring................................................................................................. 36
9.10.Weighing Profile................................................................................... 38
9.11.<WEIGHING> - Readout Mode Settings .................................................. 39
9.12.Proximity Sensors ................................................................................ 41
9.13.Autotare.............................................................................................. 41
9.14.Print Mode........................................................................................... 42
9.15.Minimum Sample Weight....................................................................... 43
9.16.Integration with Titrators ...................................................................... 45
10. MISCELLANEOUS PARAMETERS....................................................... 46
11. ADJUSTMENT .................................................................................. 48
11.1.Internal Adjustment ............................................................................. 48
11.2.External Adjustment............................................................................. 49
11.3.User Adjustment .................................................................................. 49
11.4.Adjustment Test................................................................................... 49
11.5.Automatic Adjustment .......................................................................... 49
11.6.Automatic Adjustment Time................................................................... 49
11.7.Report Printout .................................................................................... 50
11.8.Adjustment of the Drying Chamber Temperature...................................... 50
11.9.Temperature Test................................................................................. 52
12. PRINTOUTS CONTENT..................................................................... 53
12.1.Adjustment Report ............................................................................... 53
12.2.Drying Process Report Printout............................................................... 54
12.3.Other Printouts .................................................................................... 57
12.4.Non-standard printouts......................................................................... 59
12.4.1. Inserting Texts....................................................................................................................... 59
12.5.Variables............................................................................................. 62
13. WORKING MODES – General Information ....................................... 63
13.1.Working Modes Availability .................................................................... 63
13.2.Running Working Mode ......................................................................... 63
13.3.Working Mode Parameters..................................................................... 64
14. DATABASES..................................................................................... 64
14.1.Database Connected Operations............................................................. 64
14.2.Products.............................................................................................. 66
14.3.Operators............................................................................................ 66
14.4.Packaging............................................................................................ 66
14.5.Customers........................................................................................... 66
14.6.Drying Programs .................................................................................. 67
14.7.Drying Process Reports ......................................................................... 67
14.8.Ambient Conditions .............................................................................. 67
14.9.Weighings ........................................................................................... 68

- 5 -
15. SAMPLES PREPARATION................................................................. 69
15.1.Moisture Content Measurement Principle for Moisture Analyzer .................. 69
15.2.Sampling and Preparation ..................................................................... 69
16. SELECTION OF DRYING PROCESS PARAMETERS .................................... 71
16.1.Optimum Sample Mass ......................................................................... 71
16.2.Influence of Sample Mass on Measurement Repeatability .......................... 71
16.3.Drying Temperature ............................................................................. 72
16.4.Drying Profile Selection......................................................................... 72
16.5.Drying Time......................................................................................... 73
16.6.Drying Profile Analysis .......................................................................... 73
17. DRYING........................................................................................... 74
17.1.Mode Related Settings .......................................................................... 74
17.2.Drying – Quick Access Buttons............................................................... 75
18. DRYING PROCESS PERFORMED BY MEANS OF QUICK MENU ........... 75
18.1.Drying Profile and Drying Process Parameters.......................................... 76
18.2.Finish Mode ......................................................................................... 77
18.3.Unit of a Displayed and Printed Result..................................................... 78
18.4.Printout Interval................................................................................... 78
18.5.Drying Process Wizard .......................................................................... 79
19. DRYING PROCESS USING DRYING PROGRAMS DATABASE.............. 80
20. DRYING PROCESS ........................................................................... 81
20.1.End Result Prognosis ............................................................................ 85
21. COMMUNICATION ........................................................................... 88
21.1.RS232 ................................................................................................ 88
21.2.ETHERNET Settings .............................................................................. 88
21.3.Wi-Fi Settings ...................................................................................... 88
21.4.USB Ports............................................................................................ 91
22. PERIPHERALS ................................................................................. 94
22.1.Computer............................................................................................ 94
22.2.Printer ................................................................................................ 96
22.3.Record of Measurement Data Onto a USB Flash Drive ............................... 99
22.4.Barcode Scanner.................................................................................100
22.5.Ambient Conditions Module ..................................................................100
23. AMBIENT CONDITIONS................................................................. 100
24. COMMUNICATION PROTOCOL ....................................................... 103
24.1.List of Commands................................................................................103
24.2.Response Format ................................................................................104
24.3.Manual Printout / Automatic Printout .....................................................119
25. PERIPHERAL DEVICES................................................................... 120
26. ERROR MESSAGES......................................................................... 120
27. MOISTURE ANALYZER MEANS OF OPERATION .............................. 121
28. MAINTENANCE ACTIVITIES .......................................................... 121
28.1.Cleaning Moisture Analyzer Components ................................................121
28.2.Cleaning Temperature Sensor...............................................................122
28.3.Troubleshooting ..................................................................................122

- 6 -
29. ACCESSORIES................................................................................. 123
30. MOISTURE ANALYZER INFO .......................................................... 123

- 7 -
1. GENERAL INFORMATION
Dimensions:
Connectors:
1. power supply connector
2. USB 2 type B connector
3. USB 1 type A connector
4. ETHERNET connector
5. COM connector
Diagrams of connection cables:
Moisture analyzer –
computer cable (RS232)

- 8 -
Moisture analyzer - printer
cable (EPSON)
TECHNICAL SPECIFICATIONS
Moisture analyzer type
MA
50/1.X2.A
MA
50.X2.A
MA
110.X.A
MA
210.X2.A
MA
50/1.X2.IC.A
MA
50.X2.IC.A
MA
110.X.IC.A
MA
210.X2.IC.A
Max capacity
50 g
50 g
110 g
210 g
Reading unit
0.1 mg
1 mg
1 mg
1 mg
Tare range
- 50 g
- 50 g
- 110 g
- 210 g
Maximum sample weight
50 g
50 g
110 g
210 g
Moisture content
readability
0.0001% 0.001 %
Moisture content
repeatability
+/- 0.05% (sample ~2g), +/- 0.01% (sample ~10g)
Drying temperature range
Max. 160 °C
Max. 250 °C (WH)
Heating module
IR emitter (NP)
halogen lamp (NH or WH)
metal heater (NS)
Drying method
4 drying profiles: standard, fast, step, mild
Finish mode
3 modes: automatic, time-defined, manual
Operating temperature
+10 °C - +40 °C
Power supply
230V 50Hz AC
Display
5” colour capacitive touch screen
Weighing pan dimensions
ø 90 mm, h = 8 mm
Drying chamber
dimensions
120 x 120 x 20 mm
Net/gross weight
~4.9 / 6.4 kg
Packaging dimensions
470×380×336 mm
Power consumption
6W during weighing
max 450W during drying
Ingress protection
IP 41
All moisture analyzers are equipped with auto opened/closed drying chamber lid.
Moisture analyzers of MA xx.X2.IC.A series are additionally equipped with mechanism of
auto adjustment.

- 9 -
2. BASIC SAFETY PRECAUTIONS
2.1. Warning Symbols and Signals
Safety precautions are marked with special descriptions and warning signs. They inform
and warn an operator of possible dangers.
Ignoring the safety warnings may cause injuries, damage of the moisture analyzer,
its inappropriate operation and errors of measurements.
2.1.1. Warning Descriptions
WARNING
Medium risk danger that can lead to a serious injury or death.
CAUTION
Low risk danger that can lead to moisture analyzer damage or
dysfunction, loss of data or minor or moderate injury.
NOTE
Critical information on the moisture analyzer.
2.1.2. Warning Symbols
Electrocution
Acid/Corrosion
Potential danger
Flammable or explosive substances
Toxic substances
Hot surface
2.2. Precautions
WARNING!
The use of the moisture analyzer regardless of both, safety information and service
manual guidelines may cause health damage and even death.
WARNING:
Nominal voltage for a moisture analyzer is 230V AC. It means that safety
usage precautions for low voltage devices must be abide by while
operating the device. Three-core power supply cable with grounding pin
comes standard with a moisture analyzer. If necessary, an extension cord
can be used as long as it meets the applicable standards and has a
protective ground conductor. Intended disconnection of the grounding
cable is forbidden.
Voltage range for moisture analyzers marked with AC 230V symbol: 220
V–240 V, 50/60 Hz,
CAUTION:

- 10 -
Drying chamber cannot be opened during operation (drying process). It is
due to the fact that a halogen lamp and its glass shield may reach the
temperature of up to 400°C.
When setting up the moisture analyzer leave enough space to prevent heat
from building up and to keep your analyzer from overheating. Leave about
20 cm around the instrument and about 1 m above.
Air vents that are located in the housing cannot be covered, sealed or
blocked in any other way.
Do not put any flammable substances on, under or near the moisture
analyzer.
Be particularly careful when removing the sample from the drying chamber.
The sample itself, the drying chamber, shields and the weighing pan can
still be extremely hot.
In case of any maintenance work (cleaning the inside of the drying
chamber), the moisture analyzer must be switched off.
Wait until all the components have cooled down.
Do not perform any modification to the heating module.
Same types of samples require taking particular safety precautions.
They can pose a danger for people and objects. It is always the user who is liable
for possible damages caused by the use of an inappropriate sample.
CAUTION:
Corrosion Substances that release aggressive vapours (e.g. acids) during
the heating process. In this case, it is recommended to work with small
samples. Otherwise, vapours can condense on cold housing parts and
cause corrosion.
WARNING:
Fire or explosion Flammable or explosive substances, substances
containing solvents or releasing flammable or explosive gases or vapours.
Perform a risk analysis when in doubt relating to the sample characteristics
before carrying out the procedure. For this type of samples apply the drying
temperatures as low as possible to prevent flames or explosion. During the
analysis it is necessary to wear protective glasses and gloves. The
samples should be relatively small.
Under no circumstances can the instrument be left unsupervised!
WARNING:
Substances containing toxic and caustic or corrosive components
Substances that release toxic gases or vapours can cause irritations (eyes,
skin or respiratory system), illnesses or even death. Dry such substances
only in fume cupboards.
Under no circumstances should the instrument be used in an area with any risk of
explosion.
The moisture analyzer is not designed to operate in hazardous areas.

- 11 -
2.3. Intended Use
The moisture analyzer of MA X2 series is designed to determine: relative moisture
content in small samples of various substances, dry mass content in small samples and
mass of weighed objects.
The moisture analyzer ensures fast and precise determination of sample's moisture
content.
With use of a graphic touch screen the operation and measurement is simplified. A
moisture analyzer can be used to determine moisture content of different materials. At
the initial stage of measurement, the device precisely determines the mass of an object
placed on instrument’s weighing pan. As the mass reading is stabilized, the sample is
quickly heated by a halogen lamp, an IR emitter or a metal heater causing humidity
evaporation from the tested sample. While sampling, the moisture analyzer is
continuously checking the loss of mass, and on calculation, it displays current moisture
content in a tested sample.
Compared to conventional methods of humidity content determination of various
substances, application of moisture analyzer considerably shortens measurement time
and simplifies testing procedure.
MA X2 moisture analyzer allows setting multiple parameters which influence the
procedure of moisture content determination in a sample, such as: temperature, time,
drying modes, etc.
2.4. Good Weighing Practice
CAUTION!
Do not open the drying chamber during drying process. Moisture analyzer features a
halogen lamp which is a very powerful heat source. Thus, operator should pay special
attention no to touch those elements of a moisture analyzer that get hot while drying
procedure (i.e.: disposable pan, pan handle, and inner shields of the drying chamber).
Remember that some of tested samples may become dangerous if heated (appearance
of poisoning vapours, danger of ignition or explosion).
MA X2 moisture analyzer is not intended for dynamic weighing. Even if small amounts of
a sample are added to or taken off the weighing pan, the mass readout should only be
taken on stabilization of measurement result (upon displaying pictogram).
Do not place any magnetic materials on the weighing pan. This can cause damage of
the measuring system of the instrument.
Be sure to avoid impact shock and overloading the moisture analyzer in excess of the
prescribed maximum measuring range (max capacity), minus any possible tare weight
that has been applied.
Never use the moisture analyzer in an environment endangered by explosion!
This moisture analyzer is not adjusted for operation in explosive areas.
There must not be any modification made to the moisture analyzer.
2.5. Precautions
RADWAG moisture analyzer adheres to all binding safety regulations. Nevertheless there
are exceptional circumstances that may cause danger.
Do not open the instrument’s housing. Inside there are no parts that would require
maintenance, repair or replacement carried out by an operator. In case of any problems,
contact RADWAG service or a distributor.
Use the device only as intended. Follow this user manual in terms of installation and
configuration of the device.

- 12 -
Since use of the moisture analyzer conversely to safety precautions and service manual
guidelines may be hazardous to operator’s health and life, it is obligatory to read them
carefully:
•Use the moisture analyzer to determine humidity content in samples and to
determine mass of a tested sample; any other use of the moisture analyzer may be
dangerous both to the device and the operator,
•Before commissioning the moisture analyzer, make sure that the nominal power of
the device specified on its data plate is compatible with the supply in the mains to
which the moisture analyzer is to be plugged in,
•Halogen lamp and IR emitter can only be changed by an authorized service
employee,
•Protect moisture analyzer against contacts with liquids, it might lead to electrocution,
fire, emission of substances containing toxic or caustic vapour, emission of explosive
substances.
2.6. Warranty
The warranty does not cover:
•defects being an effect of not respecting service manual guidelines,
•using the moisture analyzer conversely to its intended use,
•any modifications of a moisture analyzer or cases when its housing has been
opened (damaged protective stickers),
•mechanical defects or defects caused by liquids, water and natural wear,
•defects caused by inappropriate setting or by electrical wiring failures,
•overloading of the measuring mechanism.
2.7. Supervision over Metrological Parameters
Metrological parameters need to be checked in determined time intervals. Inspection
frequency is conditioned by ambient conditions in which the moisture analyzer is used,
kind of carried out processes and adopted quality management system.
2.8. Service Manual Significance
It is very important to read the service manual carefully before switching on and starting
up moisture analyzer operation, even if you are experienced and have worked with this
type of instrument before.
2.9. Staff Competence
The moisture analyzer should be utilized and supervised only by users who are trained
and experienced in such type of instruments.
In order to use the moisture analyzer, first read the service manual. Keep these
instructions for the future reference.
Do not make any design modifications. Additional equipment compatible with the
moisture analyzer and spare parts should be supplied by RADWAG or an authorized
distributor.

- 13 -
2.10. Protective Clothing
While working with the instrument use protective clothing, this is to take safety precautions
against potential hazards source of which might be tested samples and ingredients.
Use the following while carrying out tests:
•protective apron,
•protective glasses,
•protective gloves (while working with hazardous chemical substances).
Before the use of the above-mentioned protective clothing, make sure that it has been
designed to be used with specific samples and that it is not damaged.
3. TRANSPORT AND STORAGE
3.1. Delivery Check
Upon delivery it is necessary to check the package and the device, make sure that your
package bears no signs of damage.
3.2. Packaging
Keep all package elements should your device be transported in the future. Remember
that only original packaging can be used for shipping purposes. Prior packing, uncouple
any cables, remove any separable components (weighing pan, shields, inserts). The
device components must be packed into an original packaging providing protection
against potential damage during transportation.
4. UNPACKING AND INSTALLATION
4.1. Place of Use
•Operate the device in a workroom free of vibrations and shakes, where there are no
air drafts nor dust. The workstation has to be located up to 2000 m above sea level.
•When setting up the moisture analyzer leave enough space to prevent heat from
building up and to keep your analyzer from overheating. Leave about 20 cm around
the instrument and about 1 m above.
•Make sure that the ambient temperature ranges between: +10°C ÷+40°C.
•Relative humidity cannot exceed 80% at the temperature of 31°C, decreasing
linearly to 50% of the relative humidity at the temperature of 40°C.
•Place the moisture analyzer either on a robust-design table or on a wall bracket,
which is both distant from heat sources and insusceptible to vibrations.
•Take special precaution while weighing magnetic objects, as part of the moisture
analyzer is a strong magnet.

- 14 -
4.2. Unpacking
Carefully take the device out of the packaging, remove the transport lock and gently place
the moisture analyzer at its workplace. Install the components, follow the diagram:
Install:
-drying chamber base insert (1),
-draft shield (2)
-weighing pan handle (3),
-weighing pan cross-shaped holder (4),
-disposable pan (5).
Positioning the cross-shaped holder:
When installing the cross-shaped holder (pan supporter)
pay special attention to the correct positioning of its
mandrel. The mandrel features a cut providing unique
positioning of the holder against the pan handle, thus
preventing their contact and friction.
Positioning the cross-shaped holder:
-assemble the holder onto the mandrel and turn it
slightly so that the mandrel cuts are located in their
unique and correct position,
-turn the mandrel gently so as not to damage moisture
analyzer’s measuring system.
4.3. Levelling
It is necessary to level the instrument prior connecting it to the mains. To
level the moisture analyzer turn its feet until an air bubble takes central
position.
4.4. Standard Delivery Components List
•Moisture analyzer.
•Drying chamber base insert
•Drying chamber shield.
•Weighing pan handle
•Cross-shaped holder
•Disposable pan
•Power cord
•User manual - CD version.

- 15 -
4.5. Maintenance Activities
Maintenance activities:
1.Disassemble the weighing pan and other detachable components (the components
differ depending on the weighing instrument model, read section: UNPACKING AND
INSTALLATION). Be careful while installing the components so as not to cause any
damage to the moisture analyzer mechanism.
2.In order to ease cleaning of glass anti-draft chamber panes, it is permissible to remove
them following the below instruction.
Caution:
In case of heavy dust occurring at the place of moisture analyzer operation, it is
recommended to commission an inspection of the device to be carried out by RADWAG
service every 6 months.
Cleaning the weighing pan while still installed may cause damage of the measuring system.
Cleaning ABS components:
To clean dry surfaces and avoid smudging, use clean non-colouring cloths made of cellulose
or cotton. You can use a solution of water and detergent (soap, dishwashing detergent, glass
cleaner). Gently rub the cleaned surface and let it dry. Repeat cleaning process if needed.
In the case of hard to remove contamination, e.g. residues of adhesive, rubber, resin,
polyurethane foam etc., you can use a special cleaning agents based on a mixture of
aliphatic hydrocarbons that do not dissolve plastics. Before using the cleanser for all
surfaces we recommend carrying out tests. Do not use cleansers containing abrasive
substances.
Cleaning anti-draft chamber panes:
Select dissolvent depending on a dirt. Never soak the glass panes in alkaline solutions since
they interact with glass and may cause damage. Do not use cleansers containing abrasive
substances.
For organic dirt use acetone first, next use water or detergent. For other than organic dirt use
diluted acid solutions (soluble salts of hydrochloric or nitric acid) or base solutions
(ammonium or sodium base).
To remove ACIDS use protophilic solvent (sodium carbonate), to remove BASE use
protogenic solvent (mineral acid of various concentration).
In case of heavy contamination use brush and detergent, nevertheless avoid detergents
containing large and hard molecules which could potentially scratch glass panes.
At the end of the cleaning process rinse the pane using distilled water.
Use soft brush with wooden or plastic handle exclusively in order to avoid risk of scratches.
Do not use wire brush.
Rinsing is a necessary cleaning process stage allowing to remove remaining soap,
detergents and other cleansers from the panes prior their reinstallation.

- 16 -
After preliminary cleaning process stage, rinse the pane using running water first, distilled
next.
Avoid drying the panes either using paper towel or forced air circulation since some fibres,
grains or contamination of other type could permeate into the panes thus causing weighing
errors.
We do not recommend using driers when drying measuring glass tools.
It is a frequent treatment to leave glass components on a rack to dry.
Cleaning stainless steel components:
Avoid using cleansers containing any corrosive chemicals, e.g. bleach (including chlorine).
Do not use cleansers containing abrasive substances. Always remove the dirt using
microfiber cloth to avoid damage of protective coating.
In case of a daily maintenance:
1. Remove the dirt using cloth dipped in warm water.
2. For best results, add a little bit of dishwashing detergent.
Cleaning powder-coated components:
For preliminary cleaning process stage you need running water or wet sponge featuring
large holes, this will help you to remove loose, heavy dirt.
Do not use cleansers containing abrasive substances.
Next, using cloth and cleanser-water solution (soap, dishwashing liquid) gently rub the
cleaned surface.
Avoid using cleanser without water since it may result with damage of the cleaned surface,
please mind that large amount of water mixed with cleanser is a must.
Cleaning Aluminium Components
While cleaning aluminium components use products acid by nature, e.g. spirit vinegar,
lemon. Do not use cleansers containing abrasive substances. Avoid using hard brush, this
may cause scratches. It is recommended to use microfibre cloth.
While polishing the surface use circular movements. Use clean, dry cloth to make the
surface shine.
4.6. Connecting the Moisture Analyzer to the Mains
The moisture analyzer can be plugged to the mains only by means of an original
power cord, which comes standard with the instrument. Rated voltage (specified on
the device’s data plate) must be compatible with the mains rated voltage.
The power cord can be connected only to a socket with a ground contact. Plug the power
cord to the moisture analyzer. The moisture analyzer’s power plug is located at the back of
its housing.

- 17 -
Moisture analyzer display shows name and software number first, next an indication 0.000 g
(moisture analyzers with readability of 1 mg) or 0.0000 g (moisture analyzers with readability
of 0.1 mg). If the indication is different than zero, press key.
4.7. Temperature Stabilization Time
Before start of the measuring processes, it is necessary to wait until the moisture analyzer
reaches thermal stabilisation.
Moisture analyzer stored in much lower temperatures, than the workroom temperature,
before being plugged to the mains (e.g. during winter period) must be subjected to thermal
stabilisation. The thermal stabilisation period takes about 4 hours. During the thermal
stabilization, the indications on the screen can change. Potential workroom temperature
change shall occur gradually and slowly in the course of the weighing instrument operation.
4.8. Connecting Peripheral Equipment
Use only accessories and peripheral equipment recommended by the manufacturer. The
moisture analyzer must be disconnected from the mains before connecting or disconnecting
any peripherals (printer, PC computer, computer keyboard of USB type, additional display).
Upon connecting the peripherals, plug the moisture analyzer to the mains.

- 18 -
5. START-UP
•Plug the power adapter to a socket, next connect the connector to port located at
the back of the housing.
•Press key located in the top right hand corner of the panel.
•Upon completed start-up, the home screen is displayed automatically.
•The moisture analyzer runs with no operator logged in. In order to start operation it
is necessary to carry out logging procedure (for detailed logging procedure read
later sections of this service manual).
6. OPERATION PANEL
Key
Description
Press to switch the moisture analyzer ON/OFF
Press to zero the moisture analyzer
Press to tare the moisture analyzer
Press to confirm modifications/ to send the weighing result to a printer
or a computer
Function key <Esc>, press to abort parameter modifications or exit to
previous menu level
Function key <Home>, press to exit to home screen
Programmable proximity sensors, press to enable operation of freely
selected functions

- 19 -
7. HOME SCREEN
7.1. Weighing Result Window
The home screen can be divided into 3 sections:
•Top section displaying data on active working mode (pictogram and name),
metrologically important data and button enabling selection of functions available for
a particular working mode:
The top bar displays the following information:
Working mode name and symbol.
Symbol informing that wireless communication is on.
Symbol informing that communication with a USB flash
drive is on.
Symbol informing that PC keyboard is connected.
Symbol informing that printer is connected via USB.
Symbol informing that communication with a PC
computer is on.
Symbol informing that data is saved to moisture
analyzer memory.
Symbol informing that the moisture analyzer connects
with E2R system.
Symbol informing that the weighing profile is active.
•Section presenting the weighing result:
•Section comprising supplementary information on currently performed operations,
and function buttons:

- 20 -
Caution:
Data and buttons contained in the workspace are freely configurable.
For detailed instruction read section 8 of this user manual.
7.2. Drying Process Window
The home screen can be divided into 3 sections:
•Top section displaying data on active working mode (pictogram and name),
metrologically important data and button enabling selection of functions available for
a particular working mode:
•Section presenting the weighing result:
•Section comprising supplementary information on currently performed operations,
and function buttons:
Caution:
Data and buttons contained in the workspace are freely configurable.
For detailed instruction read section 8 of this user manual.