RADWAG PUE C315 User manual

Quick Start
•PUE C315
Indicator
ITKB-08-01-12-20-EN

To view the full user manual, go to the website or scan the QR code:
radwag.com/en/manuals/EHG

*The type of plug may vary depending on the country.
2. NOTES AND WARNINGS
-10 oC
+14oF
+104o
F
+40 o
C
Operate the indicator in a room free from dust where the temperature ranges
-10–40 °C (+14–104 °F) and where the relative humidity is below 80%.
Potential temperature change shall occur gradually and slowly.
Place the scale on a table or a wall bracket ensuring stability. For the most stable
and repeatable results it is recommended to use an anti-vibration table.
Place the scale away from heat
sources. Avoid exposing the scale to
the sunlight.
Avoid exposing the scale to the influ-
ence of a magnetic field. Do not weigh
magnetic substances.
Not intended for use within EX zones.
Not intended for weighing explosive or
flammable substances.
1. CONTENT
Power supply*
×1
PUE C315
Indicator
×1

3.2. Indicator Start-Up
Press ON/OFF key to start the indicator.
The indicator is ready for operation!
4. PANEL AND SCREEN
4.1. Keypad
Switching
on / off
Sending result to a
computer or report
printout / ENTER
Navigating /
Zeroing
Navigating /
Taring
Selecting working
mode / ESC
3. PREPARING FOR WORK
3.1. Indicator Temperature Stabilization
Prior to switching the device on let it
reach room temperature (estimated
stabilization time: 8 hours).
Connect the power
supply to the mains.
1 2

4.2. Home Screen
Weighing result
window, information
and communication
field.
Result stabilization
pictogram.
Zeroing
pictogram.
5.1. Working Mode Accessibility
5. BASIC OPERATIONS
Press key to select “P3.Func” parameter
and press key.
Press key to select “3.1.1.Acc” parameter
and press key.
Press key to select „YES” parameter and
press key to save settings.
When „3.1.UUGG” parameter is enabled, press
key.
5
1 2
g
3 4
Follow the above procedure
to configure other working
modes.
Simultaneously press + keys
to enter the home screen.

5.2. Working Modes
5.3. Unit Selection
When g (gram ) is the main unit, you can select the following units:
g (gram), ct (carat), lb (pound). *
Press key to enter the menu. Press key to select working mode and
press key to confirm.
1
g
2
1 2
g
3 4
* Unit pound (lb) not available for verified scales.
For detailed description of working
modes and their settings refer to
the indicator’s full user manual.
• Weighing
• Parts counting
• +/- control
• Percent weighing
• Peak hold
• Totalizing
Working modes list:
Simultaneously press + keys
to enter the home screen.
Press key to select
‘P9.Unit’ parameter and press key.
Press key to select
“9.2.Unin” parameter and press key.
Press key to select
mass unit and press key to confirm.

6. CONNECTING PERIPHERALS
Computer
Computer
Printer
Printer
Barcode
scanner
Power
supply
Additional
display
PUE C315

7. CLEANING AND MAINTENANCE
7.1. Notes and Warnings
7.2. Cleaning Tips
Avoid using aggressive cleaning
agents (e.g. solvents, cleansers
containing chlorine, corrosive
substances or bleach).
• Clean plastic components using a soft cloth slightly moistened with a solution of water
and a mild detergent (e.g. soap or dishwashing liquid).
•Dry cleaned elements using soft and dry cloth or use dust-free paper
towel to absorb the remaining moisture.
• Do not install the components until they are completely dry.
Do not use cleansers containing
abrasive substances or scouring
preparations.
Make sure that no dust or liquid
enters the sockets and the inside
of the indicator.
Prior to cleaning it is necessary to
disconnect the scale from the mains.
Unplug the connector from the
electrical socket.
For cleaning use only soft cloths made
of microfiber. Do not use any abrasive
cloths or any material that may scratch
the surface!
Apply the cleanser onto the cloth first.
Avoid applying the cleanser directly
onto the device!

www.radwag.com