RADWAG PUE C/31H User manual

Quick Start
•PUE C/31H
Indicator
ITKB-07-01-12-20-EN

1. CONTENT
Indicator
×1
To view the full user manual, go to the website or scan the QR code:
PUE C/31H
radwag.com/en/manuals/751

2. NOTES AND WARNINGS
+40 °C
+104°F
-10 °C
+14 °F
Operate the indicator in a room free from dust where the temperature ranges
-10–40 °C (14–104 °F) and where the relative humidity is below 80%. Potential
temperature change shall occur gradually and slowly.
Place the scale on a table or a wall bracket ensuring stability. For the most stable
and repeatable results it is recommended to use an anti-vibration table.
Place the scale away from heat
sources. Avoid exposing the scale to
the sunlight.
Avoid exposing the scale to the influ-
ence of a magnetic field. Do not weigh
magnetic substances.
Not intended for use within EX zones.
Not intended for weighing explosive or
flammable substances.
3. PREPARING FOR WORK
3.1. Indicator Temperature Stabilization
Prior to switching the scale on let it
reach room temperature (estimated
stabilization time: 8 hours).
Connect the indicator
to the mains.
1 2
3.2. Start-Up
Press ON/OFF key to start the indicator.
The indicator is ready for operation!

dwt C
˚
oz%pcs
mom kg
ct GNlb
Net
4. PANEL AND SCREEN
4.1. Keypad
Switching
on / off
4.2. Home Screen
Sending result to a
computer or report
printout / ENTER
Weighing result
window, information
and communication
field.
Result stabilization
pictogram
Zeroing
pictogram
Navigating /
Zeroing
Navigating /
Taring
Selecting working
mode / ESC
5.1. Working Mode Accessibility
5. BASIC OPERATIONS
Press key to select „P2.rEAd” parameter
and press key.
1 2
g
Simultaneously press + keys
to enter the home screen.

Press key to select “4.1.FFun” parameter
and press key.
Press key to select “P4.Func” parameter
and press key.
Press key to select “4.2.Funi” parameter
and press key.
Press key to select „YES” parameter and
press key to save settings.
5 6
Net
kg
Net
kg
3 4
Net
kg
Net
kg
Follow the above procedure to configure other working modes.
5.2. Working Modes
Press key to enter the menu.
1
g
2
Net
kg
Press key to select “P4.Func” parameter
and press key.

5.3. Unit Selection
When [kg] is the main unit, you can select the following units:
g (gram), ct (carat), lb (pound).*
Press key to select a working mode and
press key to confirm.
3
Net
kg
4
Net
kg
1 2
Net
kg
Net
kg
3 4
For detailed description of working
modes and their settings refer to
the full user manual.
• Weighing
• Parts counting
• +/- control
• Percent weighing
• Peak hold
• Totalizing
Working modes list:
Simultaneously press + keys to enter
the home screen.
Press key to select „P2.rEAd” parameter
and press key.
Press key to select “P.3.Unit” parameter
and press key.
Press key to select “3.1.Stun” parameter
and press key.
Press key to select “4.1.FFun” parameter
and press key.
g

5

* Unit pound (lb) is not available for verified scales.
Press key to select mass unit and press
key to confirm.
GZW &
ə
R]SFV
PRPNJ
FW *1OE
1HW
7
J
0
Computer Printer Barcode
scanner Power supply
Additional
display
6. CONNECTING PERIPHERALS

7. CLEANING AND MAINTENANCE
7.1. Notes and Warnings
7.2. Cleaning Tips
Avoid using aggressive cleaning
agents (e.g. solvents, cleansers
containing chlorine, corrosive
substances or bleach).
Avoid using cleansers containing
abrasive substances or scouring
preparations.
Make sure that no dust or liquid
enters the sockets and the inside
of the indicator.
Prior to cleaning it is necessary to
disconnect the scale from the mains.
Unplug the connector from the
electrical socket.
For cleaning use only soft cloths made
of microfiber. Do not use any abrasive
cloths or any material that may scratch
the surface!
Apply the cleanser onto the cloth first.
Avoid applying the cleanser directly
onto the device!
• STAINLESSSTEELELEMENTS,ALUMINUMcan be cleaned with a soft cloth slightly moistened
with a solution of water and a mild detergent (e.g. soap or dishwashing liquid).
• Cleanplasticcomponentsusing a soft cloth slightly moistened with a solution of water
and a mild detergent (e.g. soap or dishwashing liquid).
•Dry cleaned elements using soft and dry cloth or use dust-free paper
towel to absorb the remaining moisture
.•Donotinstallthecomponentsuntiltheyarecompletelydry.

www.radwag.com